LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Acura >> 2003 >> 3.2CL Base >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls - System & Component Testing >> Idle Control System >> Power Steering Pressure Switch Signal >> 3.2CL & 3.2TL
April 5, 2026: LEMON Manuals is launched! Read the announcement.

3.2CL & 3.2TL

  1. Turn ignition switch on. Measure voltage by backprobing between PCM 32-pin harness connector "A" terminal No. 26 (Green wire) and PCM 25-pin harness connector B terminal No. 20 (Brown/Yellow wire - A/T) or ECM 31-pin harness connector "A" terminal No. 26 (Brown/Yellow wire) and ECM 31-pin harness connector E terminal No. 20 (Green wire - M/T). See Figure or Figure . If voltage is less than one volt, go to next step. If voltage is one volt or more, go to step  3 .
  2. Start engine. Turn steering wheel to full lock. Measure voltage by backprobing between PCM 32-pin harness connector terminal No. 26 (Green wire) and PCM 25-pin harness connector terminal No. 20 (Brown/Yellow wire - A/T) or ECM 31-pin harness connector E terminal No. 20 (Green wire) and ECM 31-pin harness connector "A" terminal No. 26 (Brown/Yellow wire - M/T). See appropriate wiring diagram under ENGINE PERFORMANCE in WIRING DIAGRAMS. If battery voltage is not present, go to next step. If battery voltage is present, Power Steering Pressure (PSP) switch signal is okay.
  3. Turn ignition switch off. Disconnect PSP switch 2-pin wire harness connector. Connect fused jumper wire between PSP switch 2-pin harness connector terminals. Turn ignition switch on. Measure voltage by backprobing between PCM 32-pin harness connector terminal No. 26 (Green wire) and PCM 25-pin harness connector terminal No. 20 (Brown/Yellow wire - A/T) or ECM 31-pin harness connector E terminal No. 20 (Green wire) and ECM 31-pin harness connector "A" terminal No. 26 (Brown/Yellow wire - M/T). If voltage is less than one volt, replace PSP switch. If voltage is one volt or more check for following:
    • An open in Green wire between PCM harness connector and PSP switch 2-pin harness connector.
    • An open in Black wire between ground terminal G201 and PSP switch 2-pin harness connector.

    Repair as necessary.

  4. Turn ignition switch off. Disconnect PSP switch 2-pin harness connector. Turn ignition switch on. Measure voltage by backprobing between PCM 32-pin harness connector terminal No. 26 (Green wire) and PCM 25-pin harness connector terminal No. 20 (Brown/Yellow wire - A/T) or ECM 31-pin harness connector E terminal No. 20 (Green wire) and ECM 31-pin harness connector "A" terminal No. 26 (Brown/Yellow wire - M/T). If battery voltage is not present, go to next step. If battery voltage is present, replace PSP switch.
  5. Turn ignition switch off. Disconnect PCM 32-pin harness A connector (A/T) or ECM 31-pin harness E connector (M/T). Check continuity between ground and PCM 32-pin harness connector terminal No. 26 (Green wire) or ECM 31-pin harness connector E terminal No. 20 (Green wire). If continuity is present, repair short in Green wire between PCM/ECM harness connector and PSP switch 2-pin harness connector. If continuity is not present, cut temporary key from a non-immobilizer key blank and tape donor vehicle key to it backwards in order to deactivate immobilizer system during testing. Substitute known-good PCM, then recheck. If symptom or indication goes away, replace original PCM.
scientia non olet · About LEMON Manuals