DTC P2101: Throttle Actuator System Malfunction

CAUTION: Do not insert your fingers into the installed throttle body when you turn the ignition switch ON (II) or while the ignition switch is ON (II). If you do, you will seriously injure your fingers if the throttle valve is activated.

NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information (see GENERAL TROUBLESHOOTING INFORMATION ).

Turn the ignition switch ON (II).
Clear the DTC with the HDS.
Do the ETCS TEST in the INSPECTION MENU with the HDS.
Check for Temporary DTCs or DTCs with the HDS.
Is DTC P2101 indicated?

YES - Go to step 7.

NO - Go to step 5.
Test-drive the vehicle for several minutes in the range of these recorded freeze data parameters:
- ENGINE SPEED
- VSS
- APP SENSOR
Check for Temporary DTCs or DTCs with the HDS.
Is DTC P2101 indicated?

YES - Go to step 7.

NO - Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the throttle body and at the throttle actuator control module, then clean the throttle body (see THROTTLE BODY CLEANING ).
Turn the ignition switch OFF.
Disconnect the intake air duct from the throttle body.
Turn the ignition switch ON (II).
Clear the DTC with the HDS.
Do the ETCS TEST in the INSPECTION MENU with the HDS.
Visually check the throttle valve operation.
Does the throttle valve operate smoothly?

YES - Clean the throttle body (see THROTTLE BODY CLEANING ), then go to step 21 and recheck. If DTC P2101 is indicated, go to step 18.

NO - Go to step 13.
Turn the ignition switch OFF.
Disconnect the throttle body 6P connector.
Disconnect the throttle actuator control module 16P connector.
Connect throttle body 6P connector terminals No. 5 and No. 6 with a jumper wire.

Fig 1: Connecting Throttle Body 6P Connector Terminals No. 5 And No. 6 With Jumper Wire
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Check for continuity between throttle actuator control module 16P connector terminals No. 1 and No. 8.

Fig 2: Checking Continuity Between Throttle Actuator Control Module 16P Connector Terminals No. 1 And No. 8
Courtesy of AMERICAN HONDA MOTOR CO., INC.

Is there continuity?

YES - Substitute a known-good throttle actuator control module (see THROTTLE ACTUATOR CONTROL MODULE REPLACEMENT ), then go to step 20 and recheck. If DTC P2101 is not indicated, replace the original throttle actuator control module (see THROTTLE ACTUATOR CONTROL MODULE REPLACEMENT ), then go to step 20. If DTC P2101 is indicated, go to step 18.

NO - Repair open in the wires between the throttle body and the throttle actuator control module (motor drive lines), then go to step 20.
Turn the ignition switch OFF.
Replace the throttle body (see THROTTLE BODY REMOVAL/INSTALLATION ).
Reconnect all connectors.
Turn the ignition switch ON (II).
Reset the ECM/PCM with the HDS.
Do the ECM/PCM idle learn procedure (see ECM/PCM IDLE LEARN PROCEDURE ).
Test-drive the vehicle for several minutes in the range of these recorded freeze data parameters:
- ENGINE SPEED
- VSS
- APP SENSOR
Check for Temporary DTCs or DTCs with the HDS.
Is DTC P2101 indicated?

YES - Check for poor connections or loose terminals at the throttle body and the throttle actuator control module, then clean the throttle body (see THROTTLE BODY CLEANING ), and go to step 1.

NO - Troubleshooting is complete. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTCs troubleshooting.