LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Acura >> 2007 >> RL >> Repair and Diagnosis >> Accessories & Equipment >> Seats >> Driver Position Memory System (DPMS) >> Power Seat Control Unit Input Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Power Seat Control Unit Input Test

NOTE: Before testing, troubleshoot the multiplex integrated control system first using B-CAN System Diagnosis Test Mode A (see TROUBLESHOOTING - B-CAN SYSTEM DIAGNOSIS TEST MODE A ).
  1. Turn the ignition switch OFF.
  2. Remove the driver's seat (see FRONT SEAT REMOVAL/INSTALLATION ).
    NOTE: Be careful not to scratch the interior trim.
  3. Disconnect the 40P connector (A) and 18P connector (B) from the power seat control unit (C).
    Fig 1: Identifying 40P Connector, 18P Connector And Power Seat Control Unit
    G05497332Courtesy of AMERICAN HONDA MOTOR CO., INC.
  4. Inspect the connector and socket terminals to be sure they are all making good contact.
    • If the terminals are bent, loose or corroded, repair them as necessary and recheck the system.
    • If the terminals look OK, go to step 5.
  5. With the connectors still disconnected, make the input test at the connectors.
    • If any test indicates a problem, find and correct the cause, then recheck the system.
    • If all the input tests prove OK, go to step 6.
      WIRE CAVITY CHART

      Cavity Wire Test condition Test: Desired result Possible cause if desired result is not obtained
      A37 BLU Under all conditions Check for continuity between the A37 terminal and power sunshade control unit 5P connector No. 3 terminal. There should be continuity. An open in the wire
  6. Reconnect the connectors to the power seat control unit, and make these input tests at the connectors.
    • If any test indicates a problem, find and correct the cause, then recheck the system.
    • If ail the input tests prove OK, the control unit must be faulty; replace it.
      WIRE CAVITY CHART

      Cavity Wire Test condition Test: Desired result Possible cause if desired result is not obtained
      A9 BLK Under all conditions Measure the voltage to ground: There should be less than 0.5 V.
      • Poor ground(G601)
      • An open in the wire
      B4 BLK
      B18 BLK
      A35 BLK/YEL Ignition switch ON (II) Measure the voltage to ground: There should be battery voltage.
      • Blown No. 21 (10A) fuse in the driver's under-dash fuse/relay box
      • An open in the wire
      B37 BLU Under all conditions Measure the voltage to ground: There should be battery voltage.
      • Blown No. 15 (40A) fuse in the under-hood fuse/relay box
      • Blown No. 7 (10A) fuse in the driver's under-dash fuse/relay box
      • An open in the wire
      B1 RED Under all conditions Measure the voltage to ground: There should be battery voltage.
      • Blown No. 20 (40A) fuse in the under-hood fuse/relay box
      • Blown No. 16 (20A) fuse in the driver's under-dash fuse/relay box
      • An open in the wire
      B8 BLU Under all conditions Measure the voltage to ground: There should be battery voltage.
      • Blown No. 20 (40A) fuse in the under-hood fuse/relay box
      • Blown No. 14 (20A) fuse in the driver's under-dash fuse/relay box
      • An open in the wire
      A31 BLK/BLU Shift lever in P position Measure the voltage to ground: There should be less than 1 V.
      • Faulty transmission range switch
      • An open in the wire
      Shift lever out of P position Measure the voltage to ground: There should be about 10 V. A short to ground in the wire
scientia non olet · About LEMON Manuals