Steering And Wheel Alignment - Service Information

• Servotronic
  • Notes
  • Introduction
  • Brief description of components
    • Notes
    • System functions
    • Initialisation of the Servotronic
    • Recording of the speed
    • Supplying the Servotronic valve with power
    • Undervoltage detection and overvoltage detection
  • Switch-on conditions
• Kinematic Diagnosis System and environment
  • Notes
  • 1. Foreword
    • 1.1 Objectives
    • 1.2 Further development of the BMW Kinematic Diagnosis System
    • 1.3 Technical Data
    • 1.4 Scope of delivery
    • 1.5 Accessories required
    • 1.6 Accessories recommended
  • 2. Measuring options using the BMW Kinematic Diagnosis System
    • 2.1 Front axle
    • 2.2 Rear axle
    • 2.3 Other measuring options
  • 3. System description
    • 3.1 BMW Kinematic Diagnosis System 1, based on the Beissbarth ML4000
  • 1. Mobile workstation
  • 2. Mobile compact cabinet
    • Notes
    • 3.2 Computer
    • 3.3 Graphical tablet
    • 3.4 Equipment cabinet
    • 3.5 Remote display
    • 3.6 Measuring sensors with CCD camera
    • 3.7 BMW Quick-acting clamp
    • 3.8 Rotating / sliding plates
    • 3.9 Sensor pins
    • 3.10 Spoiler adapter
    • 3.11 Quick-clamping units
    • 3.12 Retainers
  • 4. Workstation
    • 4.1 Environment
    • 4.2 Preconditions for alignment
    • 4.3 Measuring tolerance
    • 4.4 Levelling the measuring station
  • 5. Chassis-related terms
    • 5.1 Toe-differential angle
    • 5.2 Camber
    • 5.3 Toe-in
    • 5.4 Castor
    • 5.5 Geometrical drive axis / symmetrical axis
    • 5.6 Wheel displacement angle
    • 5.7 Kingpin offset
  • 6. Wheel suspension
    • Notes
    • 6.1 Rigid axle suspension
    • 6.2 Independent wheel suspension
  • 7. Wheel alignment / procedure
    • 7.1 Measuring options
    • 7.2 Preparatory work
    • 7.3 Initial / final measurement
    • 7.4 Printing out the data
  • 8. Special features
    • 8.1 Free wheel alignment
    • 8.2 System settings
  • 9. BMW Kinematic Diagnosis System comparison (Bosch - Beissbarth)
  • 10. Control modification (menu)
    • 10.1 Remote control with display
    • 10.2 Brief operating instructions
    • 10.3 Display support
  • 11. Updating the software / setpoint data
  • 11.1 Requirements
    • Notes
    • 11.2 Procedure (Beissbarth)
    • 11.3 Procedure (Bosch)
  • 12. Creating, copying and editing setpoint data
    • 12.1 Copying
    • 12.2 Creating
    • 12.3 Editing
  • 13. Special functions
    • 13.1 Customer-specific printer report header
    • 13.2 Adjusting options
    • 13.3 Rotating plate test
    • 13.4 Viewing and deleting customer entries from database
  • 14. Modifications within program
  • 15. Faults
    • 15.1 Tyre faults
    • 15.2 Front axle faults
    • 15.3 Rear axle faults