LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Buick >> 2017 >> Encore Base >> Repair and Diagnosis >> Body & Frame >> Windows >> Fixed And MOVEABLE Window System >> Diagnostic Information and Procedures >> Power Windows Malfunction >> Circuit/System Testing
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Circuit/System Testing

Test 1

    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems Off
  2. Disconnect the electrical connector: M74D Window Motor - Driver
  3. Test for less than 10 Ω between the test points: Ground circuit terminal 1 & Ground
    • If 10 Ω or greater 
    1. Disconnect Ground Connection
    2. Test for less than 2 Ω between the test points: M74D Window Motor - Driver Ground circuit terminal 1 @ Component harness & Ground Connection
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  4. Ignition On/Vehicle In Service Mode
  5. Verify a test lamp turns On between the test points: B+ circuit terminal 2 & Ground
    • If the test lamp does not turn On and the circuit fuse is OK 
    1. Ignition/Vehicle Off & Remove Test lamp
    2. Test for less than 2 Ω between the test points: M74D Window Motor - Driver B+ circuit terminal 2 @ Output terminal @ F3DB Fuse
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is OK and there is voltage at the fuse.
    • If the test lamp does not turn On and the circuit fuse is open 
    1. Ignition/Vehicle Off & Remove Test lamp
    2. Test for infinite resistance between the test points: B+ circuit terminal 2 & Ground
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the component: M74D Window Motor - Driver
    • If the test lamp turns On 
  6. Test or replace the component: M74D Window Motor - Driver

Test 2

    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems Off
  2. Disconnect the electrical connector: S79D Window Switch - Driver
  3. Test for less than 10 Ω between the test points: Ground circuit terminal 1 & Ground
    • If 10 Ω or greater 
    1. Disconnect Ground Connection
    2. Test for less than 2 Ω between the test points: Ground circuit terminal 1 @ Component harness & Ground Connection
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  4. Ignition On/Vehicle In Service Mode
  5. Verify a test lamp turns On between the test points: B+ circuit terminal 4 & Ground
    • If the test lamp does not turn On and the circuit fuse is OK 
    1. Ignition/Vehicle Off & Remove Test lamp
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is OK and there is voltage at the fuse.
    • If the test lamp does not turn On and the circuit fuse is open 
    1. Ignition/Vehicle Off & Remove Test lamp
    2. Test for infinite resistance between the test points: B+ circuit terminal 4 & Ground
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the component: S79D Window Switch - Driver
    • If the test lamp turns On 
  6. Verify the scan tool parameter: Driver Window Main Control Down Switch = Inactive
    • If not the specified state 
    1. Ignition/Vehicle Off
    2. Disconnect the electrical connector: M74D Window Motor - Driver
    3. Test for infinite resistance between the test points: Signal circuit terminal 3 @ Component harness & Ground
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the component: M74D Window Motor - Driver
    • If the specified state 
  7. Momentarily connect a 3 A fused jumper wire between the test points: Signal circuit terminal 3 & Ground circuit terminal 1

    Verify the scan tool parameter: Driver Window Main Control Down Switch = Active

    • If not the specified state 
    1. Ignition/Vehicle Off & Remove Jumper wire(s)
    2. Disconnect the electrical connector: M74D Window Motor - Driver
    3. Ignition On/Vehicle In Service Mode
    4. Test for less than 1 V between the test points: Signal circuit terminal 3 @ Component harness & Ground
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    5. Ignition/Vehicle Off
    6. Test for less than 2 Ω between the test points: Signal circuit terminal 3 @ Component harness & Signal circuit terminal 7 @ M74D Window Motor - Driver
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the component: M74D Window Motor - Driver
    • If the specified state 
  8. Verify the scan tool parameter: Driver Window Main Control Up Switch = Inactive
    • If not the specified state 
    1. Ignition/Vehicle Off
    2. Disconnect the electrical connector: M74D Window Motor - Driver
    3. Test for infinite resistance between the test points: Signal circuit terminal 6 @ Component harness & Ground
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the component: M74D Window Motor - Driver
    • If the specified state 
  9. Momentarily connect a 3 A fused jumper wire between the test points: Signal circuit terminal 6 & Ground circuit terminal 1

    Verify the scan tool parameter: Driver Window Main Control Up Switch = Active

    • If not the specified state 
    1. Ignition/Vehicle Off & Remove Jumper wire(s)
    2. Disconnect the electrical connector: M74D Window Motor - Driver
    3. Ignition On/Vehicle In Service Mode
    4. Test for less than 1 V between the test points: Signal circuit terminal 6 @ Component harness & Ground
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    5. Ignition/Vehicle Off
    6. Test for less than 2 Ω between the test points: Signal circuit terminal 6 @ Component harness & Signal circuit terminal 3 @ M74D Window Motor - Driver
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the component: M74D Window Motor - Driver
    • If the specified state 
  10. Verify the scan tool parameter: Driver Window Main Control Express Switch = Inactive
    • If not the specified state 
    1. Ignition/Vehicle Off
    2. Disconnect the electrical connector: M74D Window Motor - Driver
    3. Test for infinite resistance between the test points: Signal circuit terminal 2 @ Component harness & Ground
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the component: M74D Window Motor - Driver
    • If the specified state 
  11. Momentarily connect a 3 A fused jumper wire between the test points: Signal circuit terminal 2 & Ground circuit terminal 1

    Verify the scan tool parameter: Driver Window Main Control Express Switch = Active

    • If not the specified state 
    1. Ignition/Vehicle Off & Remove Jumper wire(s)
    2. Disconnect the electrical connector: M74D Window Motor - Driver
    3. Ignition On/Vehicle In Service Mode
    4. Test for less than 1 V between the test points: Signal circuit terminal 2 @ Component harness & Ground
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    5. Ignition/Vehicle Off
    6. Test for less than 2 Ω between the test points: Signal circuit terminal 2 @ Component harness & Signal circuit terminal 5 @ M74D Window Motor - Driver
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the component: M74D Window Motor - Driver
    • If the specified state 
  12. Test or replace the component: S79D Window Switch - Driver

Test 3

    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems Off
  2. Disconnect the appropriate electrical connector: S79P Window Switch - Passenger/S79LR Window Switch - Left Rear/S79RR Window Switch - Right Rear
  3. Test for less than 10 Ω between the test points:
    • S79P Window Switch - Passenger: Ground circuit terminal 1 & Ground
    • S79LR Window Switch - Left Rear: Ground circuit terminal 5 & Ground
    • S79RR Window Switch - Right Rear: Ground circuit terminal 5 & Ground
    • If 10 Ω or greater 
    1. Disconnect Ground Connection
    2. Test for less than 2 Ω between the test points:
      • Ground circuit terminal 1 @ S79P Window Switch - Passenger & Ground Connection
      • Ground circuit terminal 5 @ S79LR Window Switch - Left Rear & Ground Connection
      • Ground circuit terminal 5 @ S79RR Window Switch - Right Rear & Ground Connection
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  4. Ignition On/Vehicle In Service Mode
  5. Verify a test lamp turns On between the test points:
    • S79P Window Switch - Passenger: B+ circuit terminal 4 & Ground
    • S79LR Window Switch - Left Rear: B+ circuit terminal 8 & Ground
    • S79RR Window Switch - Right Rear: B+ circuit terminal 8 & Ground
    • If the test lamp does not turn On and the circuit fuse is OK 
    1. Ignition/Vehicle Off & Remove Test lamp
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is OK and there is voltage at the fuse.
    • If the test lamp does not turn On and the circuit fuse is open 
    1. Ignition/Vehicle Off & Remove Test lamp
    2. Test for infinite resistance between the test points:
      • S79P Window Switch - Passenger: B+ circuit terminal 4 & Ground
      • S79LR Window Switch - Left Rear: B+ circuit terminal 8 & Ground
      • S79RR Window Switch - Right Rear: B+ circuit terminal 8 & Ground
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the component: S79 Window Switch
    • If the test lamp turns On 
  6. Ignition/Vehicle Off
  7. Connect the electrical connector: S79 Window Switch
  8. Disconnect the electrical connector: M74 Window Motor
  9. Connect a test lamp between the test points: Control circuit terminal 1 & Control circuit terminal 2
  10. Ignition On/Vehicle In Service Mode
  11. Perform the scan tool control function: Window Motor Up & Down

    Verify the test lamp state:

    Window Motor Up = Test lamp On

    Window Motor Down = Test lamp On

    • If not the specified state 
    1. Ignition/Vehicle Off & Remove Test lamp
    2. Disconnect the electrical connector: S79 Window Switch
    3. Ignition On/Vehicle In Service Mode
    4. Test for less than 1 V between the test points:
      • Control circuit terminal 1 @ Component harness & Ground
      • Control circuit terminal 2 @ Component harness & Ground
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    1. Ignition/Vehicle Off
    2. Test for infinite resistance between the test points:
      • Control circuit terminal 1 @ Component harness & Ground
      • Control circuit terminal 2 @ Component harness & Ground
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If less than infinite resistance
    1. Test for less than 2 Ω between the test points:
      • Control circuit terminal 1 @ Component harness & Control circuit terminal 3 @ S79P Window Switch - Passenger
      • Control circuit terminal 2 @ Component harness & Control circuit terminal 2 @ S79P Window Switch - Passenger
      • Control circuit terminal 1 @ Component harness & Control circuit terminal 7 @ S79LR Window Switch - Left Rear
      • Control circuit terminal 2 @ Component harness & Control circuit terminal 6 @ S79LR Window Switch - Left Rear
      • Control circuit terminal 1 @ Component harness & Control circuit terminal 7 @ S79RR Window Switch - Right Rear
      • Control circuit terminal 2 @ Component harness & Control circuit terminal 6 @ S79RR Window Switch - Right Rear
        • If 2 Ω or greater, repair the open/high resistance in the circuit.
        • If less than 2 Ω, replace the component: S79 Window Switch
    • If the specified state 
  12. Test or replace the component: M74 Window Motor
scientia non olet · About LEMON Manuals