LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Chevrolet >> 2001 >> Prizm LSi, Standard >> Repair and Diagnosis >> Body & Frame >> Windows >> Power Window System >> System Tests >> Test D: Left Rear Window Inoperative
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Test D: Left Rear Window Inoperative

  1. If description and operation have been reviewed, go to next step. If description and operation have not been reviewed, review description and operation. See DESCRIPTION & OPERATION  .
  2. Turn ignition switch to RUN position. Operate left rear power window switch to UP and DOWN positions. If power window does not operate, go to next step. If power window operates, diagnose intermittent condition. See INTERMITTENTS in BODY CONTROL MODULES - PRIZM article.
  3. Disconnect left rear power window switch 5-pin harness connector. Turn ignition switch to RUN position. Measure voltage between ground and left rear power window harness connector terminal No. 4 (Black wire). See Figure . If battery voltage exists, go to next step. If battery voltage does not exist, go to step  15 .
  4. Turn ignition switch to LOCK position. Disconnect power window master switch 14-pin harness connector. Measure resistance in Blue/Black wire between power window master switch terminal No. 12 and left rear power window switch harness connector terminal No. 2. See Figure and Figure . If resistance is less than 2 ohms, go to next step. If resistance is 2 ohms or more, go to step  14 .
  5. Measure resistance in Red/Green wire between power window master switch terminal No. 9 and left rear power window switch harness connector terminal No. 5. See Figure and Figure . If resistance is less than 2 ohms, go to next step. If resistance is 2 ohms or more, go to step  13 .
  6. Reconnect power window master switch. Turn ignition switch to RUN position. Press and hold power window master switch (left side rear) to DOWN position. Measure voltage between ground and left rear power window harness connector terminal No. 2 (Blue/Black wire). See Figure . Press and hold power window master switch (left side rear) to UP position. Measure voltage between ground and left rear power window harness connector terminal No. 5 (Red/Green wire). Battery voltage should exist during both tests. If voltage is as specified, go to next step. If voltage is not as specified, go to step  10 .
  7. Reconnect left rear power window switch harness connector. Press and hold power window master switch (left rear window switch) to DOWN position. Measure voltage between ground and left rear power window switch harness connector by backprobing terminal No. 1 (Green wire). See Figure . Press and hold power window master switch (left rear window switch) to UP position. Measure voltage between ground and left rear power window switch harness connector by backprobing terminal No. 3 (Yellow wire). Battery voltage should exist during both tests. If voltage is as specified, go to next step. If voltage is not as specified, go to step  9 .
  8. Press and hold power window master switch to DOWN position. Measure voltage between ground and left front power window motor harness connector terminal No. 1 (Yellow wire). Press and hold power window master switch to UP position. Measure voltage between ground and left front power window motor harness connector terminal No. 2 (Green wire). Battery voltage should exist during both tests. If voltage is as specified, go to step  11 . If voltage is not as specified, go to step  12 .
  9. Inspect left rear power window switch for loose terminals or corrosion. Diagnose intermittent condition. See INTERMITTENTS in BODY CONTROL MODULES - PRIZM article. If problem still exists, go to step  16 . If problem does not exist, go to step  19 .
  10. Inspect power window master switch harness connector for loose terminals or corrosion. Diagnose intermittent condition. See INTERMITTENTS in BODY CONTROL MODULES - PRIZM article. If problem still exists, go to step  17 . If problem does not exist, go to step  19 .
  11. Inspect left rear power window motor harness connector for loose terminals or corrosion. Diagnose intermittent condition. See INTERMITTENTS in BODY CONTROL MODULES - PRIZM article. If problem still exists, go to step  18 . If problem does not exist, go to step  19 .
  12. Repair open in appropriate wire between left rear power window switch and left rear power window motor. After repair, go to step  19 .
  13. Repair open in Red/Green wire between left and right door switches. After repair, go to step  19 .
  14. Repair open in Blue/Black wire between right and left door switches. After repair, go to step  19 .
  15. Repair open in Black wire between splice SP252 and left rear power window switch. After repair, go to step  19 .
  16. Replace left rear window switch. After repair, go to step  19 .
  17. Replace power window master switch. After repair, go to step  19 .
  18. Replace left rear window motor. After repair, go to next step.
  19. Operate system to verify repair. If problem does not exist, system is okay. If problem still exists, go to step  3 .
scientia non olet · About LEMON Manuals