LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Chevrolet >> 2016 >> Suburban 3500 HD LS >> Repair and Diagnosis >> External Pages >> Different car >> Section 91 (Object Detection System And Pedestrian Protection System) >> Diagnostic Information and Procedures >> Video Processing Control Module Malfunction >> Circuit/System Testing
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Circuit/System Testing

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2015 GMC Yukon XL, 2015 GMC Yukon, 2015 Chevrolet Tahoe, 2015 Chevrolet Suburban, and 2015 Cadillac Escalade ESV. However, it is still accessible from the selected car via links, so may be relevant.

Only one camera image distorted

  1. Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the appropriate camera. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 5 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K157 Video Processing Control Module.
    • If less than 10 Ω 
  3. Ignition ON.
  4. Test for 4.8-5.2 V between the 5 V reference circuit terminal 6 and ground.
    • If less than 4.8 V 
    1. Ignition OFF, disconnect the harness connector at the K157 Video Processing Control Module.
    2. Test for infinite resistance between the 5 V reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the 5 V reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K157 Video Processing Control Module.
    • If greater than 5.2 V 
    1. Ignition OFF, disconnect the harness connector at the K157 Video Processing Control Module, ignition ON.
    2. Test for less than 1 V between the 5 V reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K157 Video Processing Control Module.
    • If between 4.8-5.2 V 
  5. Ignition ON.
  6. Test for less than 10 V between the signal circuit terminals listed below and ground:
    • Vision Signal + signal circuit terminal 1
    • Vision Signal - signal circuit terminal 4
    • If 10 V or greater 
    1. Ignition OFF, disconnect the X1 harness connector at the K157 Video Processing Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K157 Video Processing Control Module.
    • If less than 10 V 
  7. Ignition OFF.
  8. Test for infinite resistance between the signal circuit terminals listed below and ground:
    • Vision Signal + signal circuit terminal 1
    • Vision Signal - signal circuit terminal 4
    • If less than infinite resistance 
    1. Disconnect the X1 harness connector at the K157 Video Processing Control Module.
    2. Test for infinite between the signal circuit and ground.
      • If less than infinite resistance, repair the short to voltage on the circuit.
      • If infinite resistance, replace the K157 Video Processing Control Module.
    • If infinite resistance 
  9. Test for less than 2 Ω between the appropriate video signal circuit terminals listed below:
    • B174G Frontview Camera - Grille video signal (+) circuit terminal 1 and the K157 Video Processing Control Module video signal (+) circuit terminal 1 X1
    • B174G Frontview Camera - Grille video signal (+) circuit terminal 4 and the K157 Video Processing Control Module video signal (+) circuit terminal 11 X1
    • B87 Rearview Camera video signal (+) circuit terminal 1 and the K157 Video Processing Control Module video signal (+) circuit terminal 4 X1
    • B87 Rearview Camera video signal (+) circuit terminal 4 and the K157 Video Processing Control Module video signal (+) circuit terminal 14 X1
    • B225L Sideview Camera - Left video signal (+) circuit terminal 1 and the K157 Video Processing Control Module video signal (+) circuit terminal 5 X1
    • B225L Sideview Camera - Left video signal (+) circuit terminal 4 and the K157 Video Processing Control Module video signal (+) circuit terminal 15 X1
    • B225R Sideview Camera - Right video signal (+) circuit terminal 1 and the K157 Video Processing Control Module video signal (+) circuit terminal 8 X1
    • B225R Sideview Camera - Right video signal (+) circuit terminal 4 and the K157 Video Processing Control Module video signal (+) circuit terminal 18 X1
    • If 2 Ω or greater 

      Repair the open/high resistance in the circuit.

    • If less than 2 Ω 
  10. Engine running, transmission in R.
  11. Verify a clear surround vision image is displayed on the A11 Radio.
    • If a clear surround vision image is not displayed 
    1. Replace the appropriate camera.
    2. Engine running, transmission in R.
    3. Verify a clear surround vision image is displayed on the A11 Radio.
      • If a clear surround vision image is not displayed, replace the K157 Video Processing Control Module.
      • If a clear surround vision image is displayed, all OK.
    • If a clear surround vision image is displayed 
  12. All OK.

All camera images distorted with IO3

  1. Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the K157 Video Processing Control Module. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 1 V between the signal circuit terminals listed below and ground:
    • Camera signal (+) circuit terminal 6 X2
    • Camera signal (-) circuit terminal 12 X2
    • If 1 V or greater 

      Repair the short to voltage on the circuit.

    • If less than 1 V 
  3. Test for infinite resistance between the signal circuit terminals listed below and ground:
    • Camera signal (+) circuit terminal 6 X2
    • Camera signal (-) circuit terminal 12 X2
    • If less than infinite resistance 

      Repair the short to ground on the circuit.

    • If infinite resistance 
  4. Test for less than 2 Ω between the camera signal (+) circuit terminal 6 X2 and the A11 Radio video signal (+) circuit terminal 5 X1.
    • If 2 Ω or greater 

      Repair the open/high resistance in the circuit.

    • If less than 2 Ω 
  5. Test for less than 2 Ω between the camera signal (-) circuit terminal 12 X2 and the A11 Radio video signal (-) circuit terminal 4 X1.
    • If 2 Ω or greater 

      Test the signal circuit for an open/high resistance.

    • If less than 2 Ω 
  6. Replace the K157 Video Processing Control Module.
  7. Engine running, transmission in R.
  8. Verify a clear surround vision image is displayed on the A11 Radio.
    • If a clear rear vision image is not displayed 

      Replace the A11 Radio.

    • If a clear rear vision image is displayed 
  9. All OK.

All camera images distorted with IO5 or IO6

  1. Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the K157 Video Processing Control Module. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 1 V between the signal circuit terminals listed below and ground:
    • Camera signal (+) circuit terminal 6 X2
    • Camera signal (-) circuit terminal 12 X2
    • If 1 V or greater 

      Repair the short to voltage on the circuit.

    • If less than 1 V 
  3. Test for infinite resistance between the signal circuit terminals listed below and ground:
    • Camera signal (+) circuit terminal 6 X2
    • Camera signal (-) circuit terminal 12 X2
    • If less than infinite resistance 

      Repair the short to ground on the circuit.

    • If infinite resistance 
  4. Test for less than 2 Ω between the camera signal (+) circuit terminal 6 X2 and the K74 Human Machine Interface Control Module video signal (+) circuit terminal 5 X2.
    • If 2 Ω or greater 

      Repair the open/high resistance in the circuit.

    • If less than 2 Ω 
  5. Test for less than 2 Ω between the camera signal (-) circuit terminal 12 X2 and the K74 Human Machine Interface Control Module video signal (-) circuit terminal 6 X2.
    • If 2 Ω or greater 

      Test the signal circuit for an open/high resistance.

    • If less than 2 Ω 
  6. Replace the K157 Video Processing Control Module.
  7. Engine running, transmission in R.
  8. Verify a clear surround vision image is displayed on the K74 Human Machine Interface Control Module.
    • If a clear rear vision image is not displayed 

      Replace the A11 Radio.

    • If a clear rear vision image is displayed 
  9. All OK.
scientia non olet · About LEMON Manuals