Common Specs & Procedures Index
ACADIA COMMON SPECS & PROCEDURES
| SYSTEM | SPECIFICATION/PROCEDURE | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Approximate Fluid Capacities | ||
| Torque | Fastener Specifications | ||
| Axle Nut/Hub Nut | |||
| Front Wheel Drive Shaft Nut: 173 lb ft (235 N.m) Rear Wheel Drive Shaft Nut: 151 lb ft (205 N.m) |
|||
| Battery | N/A | ||
| Brakes | |||
| Bleeding Sequence | RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT Hydraulic Brake System Bleeding (Manual) Hydraulic Brake System Bleeding (Pressure) |
||
| Disc Brakes | |||
| Service Specifications | Disc Brake Component Specifications | ||
| Torque | Fastener Specifications | ||
| Charging | |||
| Generator | N/A | ||
| Torque | Fastener Specifications | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See Identifying Drive Belt Routing Figure Under Drive Belt Replacement | ||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | Pressure Stamped On Cap | ||
| Thermostat R & I | |||
| Engine Coolant Thermostat Housing Replacement | |||
| Water Pump R & I | |||
| Water Pump Replacement | |||
| Engine Mechanical | |||
| 3.6L | |||
| Compression | The lowest reading should not be less than 70 percent of the highest reading. No cylinder reading should be less than 965 kPa (140 psi). Engine Compression Test |
||
| Oil Pressure - Minimum @ Idle: 69 kPa (10 psi) | Oil Pressure - Minimum @ 2, 000 RPM: 138 kPa (20 psi) | ||
| Overhaul | Engine Mechanical Specifications | ||
| Torque | Fastener Specifications | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flex Plate (3.6L A/T) Torque | First Pass: 30 N.m (22 lb. ft.) Final Pass: Tighten 45° |
||
| Fuel System | |||
| Pressure Specification | 3.6L Ignition ON, Engine OFF - 345-690 kPa (50-100 psi) Engine at IDLE - 300-400 kPa (43-58 psi) |
||
| Fuel Pressure Test Procedure | Circuit/System Verification | ||
| Fuel Filter Location | Fuel Filter is Part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I | Fuel Pump Power Control Module Replacement | ||
| Ignition | |||
| Firing Order & Cylinder Identification | Firing Order & Cylinder Identification | ||
| Ignition Wires (Resistance) | Individual Ignition Coil/Module Assemblies | ||
| Ignition Wires (Routing) | |||
| 3.6L | Coil On Plug | ||
| Spark Plug - For application, see parts catalog | |||
| 3.6L | |||
| Gap | 0.95-1.1 mm (0.037-0.043 in) | ||
| Torque | 13 lb ft (18 N.m) | ||
| Starting | |||
| Starter | N/A | ||
| Torque | Fastener Specifications | ||
| Wheel Alignment | |||
| Adjustment Specifications | Wheel Alignment Specifications | ||
| Torque | Fastener Specifications | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 140 lb ft (190 N.m) For Lug Nut Tightening Sequence, Please See the Figure Under Installation Procedure |
||