Diagnostic Test

ACTIVE DTC
NOTE: Diagnose any TP Sensor or 5-Volt Supply DTCs before continuing.

NOTE: Maximum engine speed could be reduced while this fault is active, based on where the throttle plate is stuck.

NOTE: The PCM tests the ETC Motor by opening and closing the throttle plate before starting the engine. If the throttle plate does not return to the closed position this DTC will set.
1. Start the engine and allow it to reach normal operating temperature.
  WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing. Failure to follow these instructions may result in possible serious or fatal injury.
2. With the scan tool, select View DTCs.
  Is the status Active for this DTC?
  
  Yes
  - Go to step 2
  No
  - Refer to the *CHECKING FOR AN INTERMITTENT DTC Diagnostic Procedure. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure
THROTTLE PLATE INSPECTION
1. Turn the ignition off.
2. Remove the air cleaner assembly.
3. Check for any signs of a foreign material (ice or dirt) on the throttle plate or in the throttle bore that can cause the throttle plate to stick or not fully close.
4. Attempt to manually open the throttle plate and allow it to close. Use an appropriate tool that will not damage or mar the throttle body.
  Were any problems found?
  
  Yes
  - Repair as necessary or replace the Throttle Body Assembly. Disconnect the battery when replacing the Throttle Body Assembly. After installation is complete, use a scan tool and select the ETC Relearn function.
  - Perform the PCM Verification Test. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
  No
  - Go to step 3
TP SENSOR NO. 1 AND TP SENSOR No. 2 BOTH EQUAL 2.5 VOLTS
1. With a scan tool, perform the Throttle Follower test and monitor both TP Sensor voltages.
  Are both TP Sensor readings stuck at 2.5 volts?
  
  Yes
  - Check the TP Sensor Signal circuits for excessive resistance, being shorted together, or shorted to the Sensor Ground circuit.
  - Perform the PCM Verification Test. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
  No
  - Go to step 4
(K124) ETC MOTOR (+) CIRCUIT SHORTED TO VOLTAGE

Fig 1: Checking ETC Motor Circuit
Courtesy of CHRYSLER LLC
1. Turn the ignition off.
2. Disconnect the Throttle Body harness connector.
3. Disconnect the PCM harness connectors.
4. Turn the ignition on.
5. Measure the voltage of the (K124) ETC Motor (+) circuit.
  Is there any voltage present?
  
  Yes
  - Repair the (K124) ETC Motor (+) circuit for a short to voltage.
  - Perform the PCM Verification Test. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
  No
  - Go to step 5
(K126) ETC MOTOR (-) CIRCUIT SHORTED TO VOLTAGE

Fig 2: Checking ETC Motor Circuit
Courtesy of CHRYSLER LLC
1. Measure the voltage of the (K126) ETC Motor (-) circuit.
  Is there any voltage present?
  
  Yes
  - Repair the (K126) ETC Motor (-) circuit for a short to voltage.
  - Perform the PCM Verification Test. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
  No
  - Go to step 6
(K124) ETC MOTOR (+) CIRCUIT SHORTED TO THE (K126) ETC MOTOR (-) CIRCUIT

Fig 3: Checking ETC Motor Circuit
Courtesy of CHRYSLER LLC
1. Turn the ignition off.
2. Measure the resistance between the (K124) ETC Motor (+) circuit and the (K126) ETC Motor (-) circuit.
  Is the resistance below 100 ohms?
  
  Yes
  - Repair the short to between the (K124) ETC Motor (+) circuit and the (K126) ETC Motor (-) circuit.
  - Perform the PCM Verification Test. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
  No
  - Go to step 7
(K124) ETC MOTOR (+) CIRCUIT SHORTED TO GROUND

Fig 4: Checking ETC Motor Circuit
Courtesy of CHRYSLER LLC
1. Measure the resistance between ground and the (K124) ETC Motor (+) circuit.
  Is the resistance below 100 ohms?
  
  Yes
  - Repair the short to ground in the (K124) ETC Motor (+) circuit.
  - Perform the PCM Verification Test. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
  No
  - Go to step 8
(K126) ETC MOTOR (-) CIRCUIT SHORTED TO GROUND

Fig 5: Checking ETC Motor Circuit
Courtesy of CHRYSLER LLC
1. Measure the resistance between ground and the (K126) ETC Motor (-) circuit.
  Is the resistance below 100 ohms?
  
  Yes
  - Repair the short to ground in the (K126) ETC Motor (-) circuit.
  - Perform the PCM Verification Test. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
  No
  - Go to step 9
(K126) ETC MOTOR (-) CIRCUIT OPEN OR HIGH RESISTANCE

Fig 6: Checking ETC Motor Circuit
Courtesy of CHRYSLER LLC

NOTE: When checking circuits at the Powertrain Control Module (PCM), be careful not to damage or distort the connector terminals. Improper measurement technique could result in poor pin to terminal contact.
1. Measure the resistance of the (K126) ETC Motor (-) circuit.
  Is the resistance below 5.0 ohms?
  
  Yes
  - Go to step 10
  No
  - Repair the (K126) ETC Motor (-) circuit for an open circuit or high resistance.
  - Perform the PCM Verification Test. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
(K124) ETC MOTOR (+) CIRCUIT OPEN OR HIGH RESISTANCE

Fig 7: Checking ETC Motor Circuit
Courtesy of CHRYSLER LLC

NOTE: When checking circuits at the Powertrain Control Module (PCM), be careful not to damage or distort the connector terminals. Improper measurement technique could result in poor pin to terminal contact.
1. Measure the resistance of the (K124) ETC Motor (+) circuit.
  Is the resistance below 5.0 ohms?
  
  Yes
  - Go to step 11
  No
  - Repair the (K124) ETC Motor (+) circuit for an open circuit or high resistance.
  - Perform the PCM Verification Test. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
POWERTRAIN CONTROL MODULE (PCM)
1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Throttle Body and the Powertrain Control Module (PCM).
2. Look for any chafed, pierced, pinched, or partially broken wires.
3. Look for broken, bent, pushed out or corroded terminals.
4. Refer to any Technical Service Bulletins that may apply.
  Were any problems found?
  
  Yes
  - Repair as necessary.
  - Perform the PCM Verification Test. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
  No
  - Replace and program the Powertrain Control Module per Service Information.
  - Perform the PCM Verification Test. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .