Body Closures DTCS: PLG
PLG MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Perform Test |
|---|---|---|
| B1105 | Rear Open/Close Switch Active During Self-Test | GO to PINPOINT TEST AA. |
| B1317 | Battery Voltage High | REFER to CHARGING SYSTEM - GENERAL INFORMATION . |
| B1318 | Battery Voltage Low | REFER to CHARGING SYSTEM - GENERAL INFORMATION . |
| B1342 | ECU Is Defective | INSTALL a new PLG module. REFER to POWER LIFTGATE MODULE in this article. |
| B2019 | Cinch Time Exceeded | GO to PINPOINT TEST AC. |
| B201A | Power System Disabled Due to High Manual Closing Speed | INSTALL new liftgate assist cylinders. CLEAR the DTCs. TEST for normal operation. If DTC B201A returns, INSTALL a new PLG module. REFER to POWER LIFTGATE MODULE in this article. |
| B236A | Chime output circuit open | GO to PINPOINT TEST AE. |
| B2483 | Park Signal Open Circuit | GO to PINPOINT TEST Z. |
| B2593 | Door Reversed While Closing Due to An Obstacle Was Sensed | VERIFY obstacle is not present. CLEAR the DTCs. TEST for normal operation. If DTC B2593 returns, GO to PINPOINT TEST AD. |
| B2604 | PSD on/off switch open circuit | GO to PINPOINT TEST AA. |
| B2605 | VSS Signal Open Circuit | GO to PINPOINT TEST Z. |
| B2699 | Left Pinch Strip Open or Short to Battery | GO to PINPOINT TEST AF. |
| B2700 | Right Pinch Strip Open or Short to Battery | GO to PINPOINT TEST AF. |
| B2701 | Left Pinch Strip Stuck Active | GO to PINPOINT TEST AG. |
| B2702 | Right Pinch Strip Stuck Active | GO to PINPOINT TEST AG. |
| B2704 | Optical Sensor Power Short to Ground | GO to PINPOINT TEST Z. |
| B2713 | Unlatch Output Short to Ground | If the PLG is inoperative, GO to PINPOINT TEST Z. If the PLG does not power open (power close OK), GO to PINPOINT TEST AI. |
| B2714 | Uncinch Output Short to Ground | GO to PINPOINT TEST AC. |
| B2715 | Cinch Output Short to Ground | GO to PINPOINT TEST AC. |
| B2722 | Open/Close Switch Active During Self-Test | GO to PINPOINT TEST AA. |
| B2819 | Gate Motor Circuit Short to Battery | GO to PINPOINT TEST Z. |
| B2908 | Latch Switch Invalid | For an inoperative PLG, GO to PINPOINT TEST Z. For a PLG that stops in SECONDARY LATCH position, GO to PINPOINT TEST AC. |
| B2931 | Optical Sensor 1 Short to Battery or Open | For an inoperative PLG, GO to PINPOINT TEST Z. For a liftgate that does not stop/reverse when an obstacle is present, GO to PINPOINT TEST AH. |
| B2932 | Optical Sensor 1 Short to Ground | For an inoperative PLG, GO to PINPOINT TEST Z. For a liftgate that does not stop/reverse when an obstacle is present, GO to PINPOINT TEST AH. |
| B2933 | Optical Sensor 2 Short to Battery or Open | For an inoperative PLG, GO to PINPOINT TEST Z. For a liftgate that does not stop/reverse when an obstacle is present, GO to PINPOINT TEST AH. |
| B2934 | Optical Sensor 2 Short to Ground | For an inoperative PLG, GO to PINPOINT TEST Z. For a liftgate that does not stop/reverse when an obstacle is present, GO to PINPOINT TEST AH. |
| B2935 | Drive Unit Failure | GO to PINPOINT TEST Z. |
| B2936 | Gate Motor Open | GO to PINPOINT TEST Z. |
| B2937 | Gate Motor Short to Ground | GO to PINPOINT TEST Z. |
| B2938 | Gate Clutch Short to Battery | GO to PINPOINT TEST Z. |
| B2939 | Gate Clutch Short to Ground | GO to PINPOINT TEST Z. |
| B2940 | Chime Output Circuit Short to Ground | GO to PINPOINT TEST AE. |
| B2941 | Cinch Motor Open | GO to PINPOINT TEST AC. |
| B2942 | Cinch Output Short to Battery | GO to PINPOINT TEST AC. |
| B2943 | Uncinch Output Short to Battery | GO to PINPOINT TEST AC. |
| B2944 | Unlatch Output Short to Battery | If the PLG is inoperative, GO to PINPOINT TEST Z. If the PLG does not power open (power close OK), GO to PINPOINT TEST AI. |