Anti-Lock Brake System (Abs) Module
ANTI-LOCK BRAKE SYSTEM (ABS) MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Source | Perform Test |
|---|---|---|---|
| B1317 | Battery Voltage High | ABS Module | GO to PINPOINT TEST L . |
| B1318 | Battery Voltage Low | ABS Module | GO to PINPOINT TEST L . |
| B1342 | ECU Is Defective | ABS Module |
NOTE:
If other DTCs are present, REPAIR them before installing a new component. CLEAR the DTCs. RETRIEVE the DTCs. If DTC B1342 is retrieved again, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE
in this article. REPEAT the self-test. |
| B2477 | Module Configuration Failure | ABS Module | RECONFIGURE the ABS module. REFER to MODULE CONFIGURATION . CLEAR the DTCs. RETRIEVE the DTCs. If DTC B2477 is retrieved again, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this article. REPEAT the self-test. |
| C1095 | ABS Hydraulic Pump Motor Circuit Failure | ABS Module | GO to PINPOINT TEST D . |
| C1096 | ABS Hydraulic Pump Motor Circuit Open | ABS Module | GO to PINPOINT TEST D . |
| C1115 | ABS Power Relay Output Short Circuit To Battery | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1115 is retrieved again, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this article. CARRY OUT the self-test with the brake pedal not applied. |
| C1145 | Wheel Speed Sensor RF Input Circuit Failure | ABS Module | GO to PINPOINT TEST E . |
| C1155 | Wheel Speed Sensor LF Input Circuit Failure | ABS Module | GO to PINPOINT TEST E . |
| C1165 | Wheel Speed Sensor RR Input Circuit Failure | ABS Module | GO to PINPOINT TEST E . |
| C1175 | Wheel Speed Sensor LR Input Circuit Failure | ABS Module | GO to PINPOINT TEST E . |
| C1185 | ABS Power Relay Output Circuit Failure | ABS Module | CLEAR all DTCs. If DTC C1185 is retrieved again, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this article. CARRY OUT the self-test with the brake pedal not applied. |
| C1194 | ABS Outlet Valve Coil LF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1194 is retrieved again, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this article. CARRY OUT the self-test with the brake pedal not applied. |
| C1198 | ABS Inlet Valve Coil LF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this article. CARRY OUT the self-test with the brake pedal not applied. |
| C1210 | ABS Outlet Valve Coil RF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this article. CARRY OUT the self-test with the brake pedal not applied. |
| C1214 | ABS Inlet Valve Coil RF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this article. CARRY OUT the self-test with the brake pedal not applied. |
| C1222 | Speed Wheel Mismatch | ABS Module | GO to PINPOINT TEST F . |
| C1233 | Wheel Speed LF Input Signal Missing | ABS Module | GO to PINPOINT TEST F . |
| C1234 | Wheel Speed RF Input Signal Missing | ABS Module | GO to PINPOINT TEST F . |
| C1235 | Wheel Speed RR Input Signal Missing | ABS Module | GO to PINPOINT TEST F . |
| C1236 | Wheel Speed LR Input Signal Missing | ABS Module | GO to PINPOINT TEST F . |
| C1242 | ABS Outlet Valve Coil LR Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this article. CARRY OUT the self-test with the brake pedal not applied. |
| C1246 | ABS Outlet Valve Coil RR Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this article. CARRY OUT the self-test with the brake pedal not applied. |
| C1250 | ABS Inlet Valve Coil LR Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this article. CARRY OUT the self-test with the brake pedal not applied. |
| C1254 | ABS Inlet Valve Coil RR Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this article. CARRY OUT the self-test with the brake pedal not applied. |
| C1277 | Steering Wheel Angle 1 and 2 Circuit Failure | ABS Module | GO to PINPOINT TEST G . |
| C1278 | Steering Wheel Angle 1 and 2 Signal Faulted | ABS Module | GO to PINPOINT TEST G . |
| C1279 | Yaw Rate Sensor Circuit Failure | ABS Module | GO to PINPOINT TEST H . |
| C1280 | Yaw Rate Sensor Signal Fault | ABS Module | GO to PINPOINT TEST H . |
| C1281 | Lateral Accelerometer Circuit Failure | ABS Module | GO to PINPOINT TEST H . |
| C1282 | Lateral Accelerometer Signal Fault | ABS Module | GO to PINPOINT TEST H . |
| C1285 | Booster Solenoid Circuit Failure | ABS Module | GO to PINPOINT TEST I . |
| C1286 | Booster Mechanical Failure | ABS Module | GO to PINPOINT TEST I . |
| C1287 | Booster Pedal Force Switch Circuit Failure | ABS Module | GO to PINPOINT TEST J . |
| C1288 | Brake Pressure Transducer Main/Primary Input Circuit Failure | ABS Module | GO to PINPOINT TEST B . |
| C1329 | RF Dump Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| C1330 | LR Dump Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| C1331 | RR Dump Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| C1332 | LF Dump Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| C1333 | LR ISO Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| C1334 | LF ISO Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| C1335 | RF ISO Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| C1336 | RR ISO Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| C1404 | Traction Control Valve Rear Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this article. CARRY OUT the self-test with the brake pedal not applied. |
| C1410 | Traction Control Valve LF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this article. CARRY OUT the self-test with the brake pedal not applied. |
| C1446 | Brake Switch Circuit Failure | ABS Module | GO to PINPOINT TEST P . |
| C1527 | TC ISO Valve Solenoid 1 Overtemp | ABS Module | GO to PINPOINT TEST N . |
| C1528 | TC ISO Valve Solenoid 2 Overtemp | ABS Module | GO to PINPOINT TEST N . |
| C1529 | ECA Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| C1530 | TC Supply Valve Solenoid 1 Overtemp | ABS Module | GO to PINPOINT TEST N . |
| C1531 | TC Supply Valve Solenoid 2 Overtemp | ABS Module | GO to PINPOINT TEST N . |
| C1730 | Reference Voltage Out of Range (+5 V) | ABS Module | If any other DTC(s) are present, diagnose those DTC(s) first. CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, GO to PINPOINT TEST Q . |
| C1957 | Stability Assist Control Valve RF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this article. CARRY OUT the self-test with the brake pedal not applied. |
| C1958 | Stability Assist Control Valve LF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this article. CARRY OUT the self-test with the brake pedal not applied. |
| C1963 | Stability Control Inhibit Warning | ABS Module | This DTC is for information only. CLEAR all DTCs. |
| C1991 | Module Calibration Failure | ABS Module | GO to PINPOINT TEST M . |
| U0073 | Control Module Communication Bus OFF | CAN Network | Repair all other DTCs first. If the DTC is still present, diagnose the communication network. REFER to MODULE COMMUNICATIONS NETWORK . |
| U1050 | SCP (J1850) Invalid or Missing Data for Brakes | ABS Module | Repair all other DTCs first. If the DTC is still present, diagnose the communication network. REFER to MODULE COMMUNICATIONS NETWORK . |
| U1051 | SCP (J1850) Invalid Or Missing Data For Brakes | ABS Module | Repair all other DTCs first. If the DTC is still present, diagnose the communication network. REFER to MODULE COMMUNICATIONS NETWORK . |
| U1059 | SCP (J1850) Invalid Or Missing Data For Transmission/Transaxle/PRNDL | ABS Module | Repair all other DTCs first. If the DTC is still present, diagnose the communication network. REFER to MODULE COMMUNICATIONS NETWORK . |
| U1073 | SCP (J1850) Invalid Or Missing Data For Engine Coolant | ABS Module | Repair all other DTCs first. If the DTC is still present, diagnose the communication network. REFER to MODULE COMMUNICATIONS NETWORK . |
| U1243 | SCP (J1850) Invalid Or Missing Data For Exterior Environment | ABS Module | Repair all other DTCs first. If the DTC is still present, diagnose the communication network. REFER to MODULE COMMUNICATIONS NETWORK . |
| U1249 | SCP (J1850) Invalid Or Missing Data For Time/Date | ABS Module | Repair all other DTCs first. If the DTC is still present, diagnose the communication network. REFER to MODULE COMMUNICATIONS NETWORK . |
| U1262 | SCP (J1850) Communication Bus Fault | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK . |
| U1900 | CAN Communication Bus Fault Receiving Error | CAN Network | Repair all other DTCs first. If the DTC is still present, diagnose the communication network. REFER to MODULE COMMUNICATIONS NETWORK . |