LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2007 >> Taurus SEL >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Automatic Transmission >> Disassembly And Assembly Of Subassemblies >> Pump Assembly >> Disassembly
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Pump Assembly: Disassembly

  1. Remove the valve body separator plate bolts.
    2. Fig 1: Bolts
    GF0020268Courtesy of FORD MOTOR CO.
  2. Remove the valve body separator plates and gaskets.
    3. Fig 2: Valve Body Separator Plates & Gaskets
    GF0020269Courtesy of FORD MOTOR CO.
  3. Remove the B8 check ball and note the location.
    4. Fig 3: Identifying B8 Check Ball Location
    GF0020270Courtesy of FORD MOTOR CO.
  4. Remove the 2 bolts.
    5. Fig 4: Locating Pump Assembly Bolts
    GF0020271Courtesy of FORD MOTOR CO.
  5. Remove the 2 pump cover bolts.
    6. Fig 5: Pump Cover Bolts
    GF0020272Courtesy of FORD MOTOR CO.
    WARNING: Use extreme caution when removing spring to prevent personal injury.
    CAUTION: Place a piece of cardboard or a suitable material under a screwdriver to prevent damage to the housing gasket surface.
  6. Remove the bore ring spring.
    7. Fig 6: Bore Ring Spring
    GF0020273Courtesy of FORD MOTOR CO.
  7. Remove the pump bore ring pin.
    8. Fig 7: Pump Bore Ring Pin
    GF0020274Courtesy of FORD MOTOR CO.
  8. Remove the metal bore ring and support seal.
    1. Remove the bore ring side seal (metal).
    2. Remove the support seal (O-ring).
    9. Fig 8: Identifying Metal Bore Ring And Support Seal
    GF0020275Courtesy of FORD MOTOR CO.
  9. Remove the pump bore ring radial seal and support.
    1. Remove the pump bore ring radial seal (orange rectangular).
    2. Remove the pump bore ring radial seal support (black round).
    10. Fig 9: Identifying Pump Bore Ring Radial Seal And Support
    GF0020276Courtesy of FORD MOTOR CO.
  10. Remove the top pump vane support ring.
    11. Fig 10: Top Pump Vane Support Ring
    GF0020277Courtesy of FORD MOTOR CO.
  11. Remove the outer pump bore ring.
    12. Fig 11: Outer Pump Bore Ring
    GF0020278Courtesy of FORD MOTOR CO.
  12. Remove the vanes.
    13. Fig 12: Pump Vanes
    GF0020279Courtesy of FORD MOTOR CO.
  13. Remove the rotor.
    14. Fig 13: Pump Rotor
    GF0020280Courtesy of FORD MOTOR CO.
  14. Remove the bottom pump vane support ring.
    15. Fig 14: Bottom Pump Vane Support Ring
    GF0020281Courtesy of FORD MOTOR CO.
  15. Remove the EPC, TCC solenoids and seals.
    • Remove the bolts.
    • Remove the EPC, TCC solenoids.
    16. Fig 15: EPC & TCC Solenoids
    GF0020282Courtesy of FORD MOTOR CO.
    NOTE: The shift solenoids are interchangeable. Take note of the shift solenoid connector orientation.
  16. Remove the shift solenoids by pressing locking tab with a screwdriver and rotating them.
    17. Fig 16: Shift Solenoids
    GF0020283Courtesy of FORD MOTOR CO.
  17. Inspect the fluid pump body bearing for wear or damage.
    18. CAUTION: The machined passage surfaces of the pump body must be protected when removing the damaged bearing.
    CAUTION: Do not press with excessive force when removing the damaged bearing.
  18. If required, use the special tool and a suitable press to remove the bearing assembly.
    19. Fig 17: Removing Fluid Pump Body Bearing
    GF0020284Courtesy of FORD MOTOR CO.
scientia non olet · About LEMON Manuals