Vehicle Dynamic Systems
ABS MODULE DTC LIST
| DTC | Description | Source | Perform Test |
|---|---|---|---|
| B1317 | Battery Voltage High | ABS Module | Go to Pinpoint Test A . |
| B1318 | Battery Voltage Low | ABS Module | Go to Pinpoint Test A . |
| B1342 | ECU is Faulted | ABS Module |
NOTE:
If other DTCs are present, repair them before installing a new module. CLEAR the DTCs. RETRIEVE the DTCs. If DTC B1342 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module
. REPEAT the self-test. |
| C1095 | ABS Hydraulic Pump Motor Circuit Failure | ABS Module | Go to Pinpoint Test B . |
| C1096 | ABS Hydraulic Pump Motor Circuit Open | ABS Module | Go to Pinpoint Test B . |
| C1115 | ABS Power Relay Output Short Circuit to Battery | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1115 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1145 | Wheel Speed Sensor RF Input Circuit Failure | ABS Module | Go to Pinpoint Test C . |
| C1155 | Wheel Speed Sensor LF Input Circuit Failure | ABS Module | Go to Pinpoint Test C . |
| C1165 | Wheel Speed Sensor RR Input Circuit Failure | ABS Module | Go to Pinpoint Test C . |
| C1175 | Wheel Speed Sensor LR Input Circuit Failure | ABS Module | Go to Pinpoint Test C . |
| C1185 | ABS Power Relay Output Circuit Failure | ABS Module | CLEAR all DTCs. If DTC C1185 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1194 | ABS Outlet Valve Coil LF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1194 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1198 | ABS Inlet Valve Coil LF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1198 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1210 | ABS Outlet Valve Coil RF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1210 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1214 | ABS Inlet Valve Coil RF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1214 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1222 | Wheel Speed Mismatch | ABS Module | Go to Pinpoint Test D . |
| C1233 | Wheel Speed LF Input Signal Missing | ABS Module | Go to Pinpoint Test D . |
| C1234 | Wheel Speed RF Input Signal Missing | ABS Module | Go to Pinpoint Test D . |
| C1235 | Wheel Speed RR Input Signal Missing | ABS Module | Go to Pinpoint Test D . |
| C1236 | Wheel Speed LR Input Signal Missing | ABS Module | Go to Pinpoint Test D . |
| C1242 | ABS Outlet Valve Coil LR Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1242 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1246 | ABS Outlet Valve Coil RR Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1246 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1250 | ABS Inlet Valve Coil LR Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1250 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1254 | ABS Inlet Valve Coil RR Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1254 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1329 | ABS Outlet Valve Coil RF Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1329 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1330 | ABS Outlet Valve Coil LR Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1330 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1331 | ABS Outlet Valve Coil RR Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1331 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1332 | ABS Outlet Valve Coil LF Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1332 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1333 | ABS Inlet Valve Coil LR Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1333 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1334 | ABS Inlet Valve Coil LF Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1334 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1335 | ABS Inlet Valve Coil RF Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1335 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1336 | ABS Inlet Valve Coil RR Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1336 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1404 | Traction Control Valve Rear Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1404 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1446 | Brake Switch Circuit Failure | ABS Module | Go to Pinpoint Test E . |
| C1527 | Traction Control Rear Valve Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1527 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1531 | Dynamic Stability Control LF Valve Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1531 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1730 | Reference Voltage Out of Range (+5 V) | ABS Module | If any other DTCs are present, DIAGNOSE those DTCs first. CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1958 | Dynamic Stability Control Valve LF circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1958 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| U0073 | Control Module Communication Bus Off | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK article to diagnose the Hydraulic Control Unit (HCU) bus. |
| U1900 | CAN Communication Bus Fault - Receive Error | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK article to diagnose the HCU bus. |
| U2011 | Module Transmitted Invalid Data (Non-SCP) | ABS Module | VERIFY PCM configuration, REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION article. If the PCM is not correctly configured, CONFIGURE the PCM. If the PCM is correctly configured, REFER to MODULE COMMUNICATIONS NETWORK article to diagnose the HCU bus. |
| U2050 | No Application Present | ABS Module | CONFIGURE the ABS module. REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION article. CLEAR the DTCs. RETRIEVE the DTCs and VERIFY successful module configuration. If DTC U2050 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CLEAR the DTC. REPEAT the self-test. |
| U2051 | One or More Calibration Files Missing/Corrupt | ABS Module | CALIBRATE the ABS module, follow the directions on the scan tool. CLEAR the DTCs. CARRY OUT the ABS module self-test. RETRIEVE and RECORD any DTCs. If DTC U2051 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CLEAR the DTC. REPEAT the self-test. |
INSTRUMENT CLUSTER DTC LIST
| DTC | Description | Source | Perform Test |
|---|---|---|---|
| C1093 | Traction Control Disable Switch Circuit Failure | Instrument Cluster | Go to Pinpoint Test H . |
| - | All Other Instrument Cluster DTCs | Instrument Cluster | REFER to the Master DTC Chart in MULTIFUNCTION ELECTRONIC MODULES article. |