Cruise Control Module (C-CM)
DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| C0072:00 | Brake Temperature Too High: No Sub Type Information | ALLOW the brake system to cool. CLEAR the Diagnostic Trouble Codes (DTCs). TEST the system for normal operation. If Diagnostic Trouble Code (DTC) C0072:00 is retrieved again, INSTALL a new Anti-Lock Brake System (ABS) module. REFER to HYDRAULIC CONTROL UNIT (HCU) . |
| C1132:4B | Head Up Display: Over Temperature | REFER to DIAGNOSTIC ROUTINE H . |
| C1A67:54 | Forward Looking Sensor: Missing Calibration | REFER to DIAGNOSTIC ROUTINE E . |
| C1A67:76 | Forward Looking Sensor: Wrong Mounting Position | REFER to DIAGNOSTIC ROUTINE E . |
| C1A67:96 | Forward Looking Sensor: Component Internal Failure | REFER to DIAGNOSTIC ROUTINE D . |
| C1A67:97 | Forward Looking Sensor: Component or System Operation Obstructed or Blocked | REFER to DIAGNOSTIC ROUTINE F . |
| C1A67:98 | Forward Looking Sensor: Component or System Over Temperature | The Cruise-Control Module (C-CM) was overtemperature. This may occur during extended use or extremely high weather temperatures. The adaptive cruise control system operation resumes after the Cruise-Control Module (C-CM) cools. CLEAR the Diagnostic Trouble Codes (DTCs). |
| U0001:88 | High Speed CAN Communication Bus: Bus Off | The module cannot communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this Diagnostic Trouble Code (DTC)). CLEAR the Diagnostic Trouble Code (DTC). REPEAT the Network Test with the scan tool. VERIFY the integrity of the connectors and wiring. |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | REFER to DIAGNOSTIC ROUTINE G . |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | REFER to DIAGNOSTIC ROUTINE H . |
| U0123:00 | Lost Communication With Yaw Rate Sensor Module: No Sub Type Information | REFER to DIAGNOSTIC ROUTINE I . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | REFER to DIAGNOSTIC ROUTINE S . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | REFER to DIAGNOSTIC ROUTINE J . |
| U0158:00 | Lost Communication With Head Up Display: No Sub Type Information | REFER to DIAGNOSTIC ROUTINE K . |
| U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | REFER to DIAGNOSTIC ROUTINE L . |
| U0300:55 | Internal Control Module Software Incompatibility: Not Configured | REFER to DIAGNOSTIC ROUTINE N . |
| U0401:68 | Invalid Data Received from ECM/PCM A: Event Information | This Diagnostic Trouble Code (DTC) sets when the Cruise-Control Module (C-CM) receives invalid network data from the Powertrain Control Module (PCM) with a faulted Vehicle Speed Sensor (VSS) signal, Accelerator Pedal Position (APP) signal, cruise control switch input or gear position input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. CHECK the vehicle service history for recent service actions related to this module. This Diagnostic Trouble Code (DTC) sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool (REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) for further information). If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to CRUISE CONTROL MODULE (C-CM) . |
| U0418:68 | Invalid Data Received From Brake System Control Module: Event Information | This Diagnostic Trouble Code (DTC) sets when the Cruise-Control Module (C-CM) receives invalid network data from the Anti-Lock Brake System (ABS) module with a faulted brake signal input, steering wheel angle input or vehicle speed input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. CHECK the vehicle service history for recent service actions related to this module. This Diagnostic Trouble Code (DTC) sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool (REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) for further information). If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to CRUISE CONTROL MODULE (C-CM) . |
| U0424:68 | Invalid Data Received From HVAC Control Module: Event Information | This Diagnostic Trouble Code (DTC) sets when the Cruise-Control Module (C-CM) receives invalid network data from the HVAC module with a faulted sunload sensor input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. CHECK the vehicle service history for recent service actions related to this module. This Diagnostic Trouble Code (DTC) sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool (REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) for further information). If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to CRUISE CONTROL MODULE (C-CM) . |
| U0429:68 | Invalid Data Received From Steering Column Control Module: Event Information | This Diagnostic Trouble Code (DTC) sets when the Cruise-Control Module (C-CM) receives invalid network data from the Steering Column Control Module (SCCM) with a faulted cruise control switch input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0459:68 | Invalid Data Received From Head Up Display: Event Information | REFER to DIAGNOSTIC ROUTINE H . |
| U0513:68 | Invalid Data Received From Yaw Rate Sensor Module: Event Information | This Diagnostic Trouble Code (DTC) sets when the Cruise-Control Module (C-CM) receives invalid network data from the Restraints Control Module (RCM) with a faulted yaw rate input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. CHECK the vehicle service history for recent service actions related to this module. This Diagnostic Trouble Code (DTC) sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool (REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) for further information). If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to CRUISE CONTROL MODULE (C-CM) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This Diagnostic Trouble Code (DTC) sets when either the Cruise-Control Module (C-CM) detects that the BCM is not configured correctly or the Cruise-Control Module (C-CM) configuration has not been completed. DETERMINE which module (BCM or Cruise-Control Module (CCM)) has been replaced. CHECK the vehicle service history for recent service actions related to this module. This Diagnostic Trouble Code (DTC) sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool (REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) for further information). If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to CRUISE CONTROL MODULE (C-CM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This Diagnostic Trouble Code (DTC) sets when the Cruise-Control Module (C-CM) detects the Body Control Module (BCM) is not transmitting the correct configuration information. The Body Control Module (BCM) needs to be configured. CHECK the vehicle service history for recent service actions related to this module. This Diagnostic Trouble Code (DTC) sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool (REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) for further information). If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to CRUISE CONTROL MODULE (C-CM) . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If Diagnostic Trouble Code (DTC) U3000:41 is retrieved again, INSTALL a new Cruise-Control Module (C-CM). REFER to CRUISE CONTROL MODULE (C-CM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. RETEST the adaptive cruise control system. REPEAT the self-test. If Diagnostic Trouble Code (DTC) U3000:42 is retrieved again, INSTALL a new Cruise-Control Module (C-CM). REFER to CRUISE CONTROL MODULE (C-CM) . |
| U3000:44 | Control Module: Data Memory Failure | CLEAR the DTCs. RETEST the adaptive cruise control system. REPEAT the self-test. If Diagnostic Trouble Code (DTC) U3000:44 is retrieved again, INSTALL a new Cruise-Control Module (C-CM). REFER to CRUISE CONTROL MODULE (C-CM) . |
| U3000:49 | Control Module: Internal Electronic Failure | CLEAR the DTCs. REPEAT the self-test. If Diagnostic Trouble Code (DTC) U3000:49 is retrieved again, INSTALL a new Cruise-Control Module (C-CM). REFER to CRUISE CONTROL MODULE (C-CM) . |
| U3000:63 | Control Module: Circuit/Component Protection Time-Out | REFER to DIAGNOSTIC ROUTINE O . |
| U3000:66 | Control Module: Signal Has Too Many Transitions/Events | REFER to DIAGNOSTIC ROUTINE P . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | REFER to DIAGNOSTIC ROUTINE Q . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | REFER to DIAGNOSTIC ROUTINE R . |