Steering Column Control Module (SCCM)
SCCM DTC CHART
| DTC | Description | Action |
|---|---|---|
| B1007:09 | High-Beam Headlamp Switch: Component Failure | INSTALL a new multifunction switch. REFER to Steering Column Multifunction Switch
. TEST the system for normal operation. If the concern still exists, INSTALL a new SCCM. REFER to Steering Column Control Module (SCCM) . |
| B1008:09 | Wiper Mode Switch: Component Failure | INSTALL a new wiper/washer switch. REFER to WIPER AND WASHER SWITCH . |
| B1051:09 | Front Washer Switch: Component Failure | INSTALL a new wiper/washer switch. REFER to WIPER AND WASHER SWITCH . |
| B1052:09 | Rear Washer Switch: Component Failure | INSTALL a new wiper/washer switch. REFER to WIPER AND WASHER SWITCH . |
| B10A6:09 | Main Light Switch: Component Failure | INSTALL a new FLM. REFER to FRONT LIGHTING CONTROL MODULE (FLM) . |
| B10AD:02 | Rain Sensor: General Signal Failure | If the rain sensitive wipers do not operate, REFER to DIAGNOSTIC ROUTINE G : The Rain Sensitive Wipers Do Not Operate. If the rain sensitive wipers operate correctly, DISREGARD this DTC. |
| B10AD:08 | Rain Sensor: Bus Signal/Message Failure | If the windshield wipers only operate when high speed mode is selected, REFER to DIAGNOSTIC ROUTINE F
: The Windshield Wipers Operate in High Speed Only. If the rain sensitive wipers do not operate, REFER to DIAGNOSTIC ROUTINE G : The Rain Sensitive Wipers Do Not Operate. |
| B10AD:49 | Rain Sensor: Internal Electronic Failure | INSTALL a new rain sensor. REFER to RAIN SENSOR . |
| B10AD:55 | Rain Sensor: Not Configured | This DTC sets due to incomplete or incorrect module programming, or due to an internal failure of the module. If the module has just recently been reprogrammed, attempt to PROGRAM the module again. RETRIEVE SCCM DTCs . If the DTC returns, INSTALL a new SCCM. REFER to Steering Column Control Module (SCCM) . |
| B1124:09 | Lamp Fade Control: Component Failure | INSTALL a new FLM. REFER to FRONT LIGHTING CONTROL MODULE (FLM) . |
| B1131:02 | Wiper Motor Module: General Signal Failure | If the windshield wipers are inoperative in all modes, REFER to DIAGNOSTIC ROUTINE A : The Wipers Are Inoperative - Windshield. If the windshield wipers only operate when high speed mode is selected. REFER to DIAGNOSTIC ROUTINE F : The Windshield Wipers Operate in High Speed Only. If the windshield wipers operate correctly, disregard this DTC. |
| B1131:08 | Wiper Motor Module: Bus Signal / Message Failure | If the windshield wipers are inoperative in all modes, REFER to DIAGNOSTIC ROUTINE A : The Wipers Are Inoperative - Windshield. If the windshield wipers only operate when high speed mode is selected. REFER to DIAGNOSTIC ROUTINE F : The Windshield Wipers Operate in High Speed Only. If the windshield wipers operate correctly, disregard this DTC. |
| B11D9:16 | Vehicle Battery: Circuit Below Threshold | REFER to Diagnostic Routine M: B11D9:16 . |
| B11D9:17 | Vehicle Battery: Circuit Above Threshold | REFER to Diagnostic Routine N: B11D9:17 . |
| B12F7:09 | Single Wipe Switch: Component Failure | INSTALL a new wiper/washer switch. REFER to WIPER AND WASHER SWITCH . |
| B1368:11 | Adjustable Pedal Position Feedback Sensor: Circuit Short To Ground | REFER to DIAGNOSTIC ROUTINE C : The Adjustable Pedals Only Move in 1-Second Intervals. |
| B1368:12 | Adjustable Pedal Position Feedback Sensor: Circuit Short To Battery | REFER to DIAGNOSTIC ROUTINE C : The Adjustable Pedals Only Move in 1-Second Intervals. |
| B1369:09 | Pedal Adjustment Switch: Component Failure | INSTALL a new pedal adjust switch. TEST the system for normal operation. If the concern still exists, INSTALL a new SCCM. REFER to Steering Column Control Module (SCCM) . |
| B137D:18 | Pedal Adjustment Motor: Circuit Current Below Threshold | REFER to DIAGNOSTIC ROUTINE D : The Adjustable Pedals are Inoperative or Do Not Operate Correctly - Using the Pedal Adjust Switch. |
| B137D:19 | Pedal Adjustment Motor: Circuit Current Above Threshold | REFER to DIAGNOSTIC ROUTINE D : The Adjustable Pedals are Inoperative or Do Not Operate Correctly - Using the Pedal Adjust Switch. |
| B137D:71 | Pedal Adjustment Motor: Actuator Stuck | REFER to DIAGNOSTIC ROUTINE D : The Adjustable Pedals are Inoperative or Do Not Operate Correctly - Using the Pedal Adjust Switch. |
| B137F:09 | Steering Wheel Left Switch Pack: Component Failure | For message center concerns, REFER to DIAGNOSTIC ROUTINE AD
: The Message Center Is Not Operating Correctly. For cruise control concerns, REFER to DIAGNOSTIC ROUTINE C : The Cruise Control Switch Is Inoperative Or Does Not Operate Correctly. |
| B137F:11 | Steering Wheel Left Switch Pack: Circuit Short to Ground | For message center concerns, REFER to DIAGNOSTIC ROUTINE AD
: The Message Center Is Not Operating Correctly. For cruise control concerns, REFER to DIAGNOSTIC ROUTINE C : The Cruise Control Switch Is Inoperative Or Does Not Operate Correctly. |
| B137F:17 | Steering Wheel Left Switch Pack: Circuit Voltage Above Threshold | For message center concerns, REFER to DIAGNOSTIC ROUTINE AD
: The Message Center Is Not Operating Correctly. For cruise control concerns, REFER to DIAGNOSTIC ROUTINE C : The Cruise Control Switch Is Inoperative Or Does Not Operate Correctly. |
| B1380:09 | Steering Wheel Right Switch Pack: Component Failure | For premium audio system, REFER to PINPOINT TEST T: THE STEERING WHEEL SWITCHES ARE INOPERATIVE OR DO NOT OPERATE CORRECTLY
: Steering Wheel Controls Are Inoperative Or Do Not Operate Correctly. For premium plus audio system, REFER to PINPOINT TEST T: THE STEERING WHEEL SWITCHES ARE INOPERATIVE OR DO NOT OPERATE CORRECTLY : The Steering Wheel Controls Are Inoperative Or Do Not Operate Correctly. For Sony® sound audio system, REFER to PINPOINT TEST U: THE STEERING WHEEL SWITCHES ARE INOPERATIVE OR DO NOT OPERATE CORRECTLY : The Steering Wheel Controls Are Inoperative Or Do Not Operate Correctly. |
| B1380:11 | Steering Wheel Right Switch Pack: Circuit Short to Ground | For premium audio system, REFER to PINPOINT TEST T: THE STEERING WHEEL SWITCHES ARE INOPERATIVE OR DO NOT OPERATE CORRECTLY
: Steering Wheel Controls Are Inoperative Or Do Not Operate Correctly. For premium plus audio system, REFER to PINPOINT TEST T: THE STEERING WHEEL SWITCHES ARE INOPERATIVE OR DO NOT OPERATE CORRECTLY : The Steering Wheel Controls Are Inoperative Or Do Not Operate Correctly. For Sony® sound audio system, REFER to PINPOINT TEST U: THE STEERING WHEEL SWITCHES ARE INOPERATIVE OR DO NOT OPERATE CORRECTLY : The Steering Wheel Controls Are Inoperative Or Do Not Operate Correctly. |
| B1380:17 | Steering Wheel Right Switch Pack: Circuit Voltage Above Threshold | For premium audio system, REFER to PINPOINT TEST T: THE STEERING WHEEL SWITCHES ARE INOPERATIVE OR DO NOT OPERATE CORRECTLY
: Steering Wheel Controls Are Inoperative Or Do Not Operate Correctly. For premium plus audio system, REFER to PINPOINT TEST T: THE STEERING WHEEL SWITCHES ARE INOPERATIVE OR DO NOT OPERATE CORRECTLY : The Steering Wheel Controls Are Inoperative Or Do Not Operate Correctly. For Sony® sound audio system, REFER to PINPOINT TEST U: THE STEERING WHEEL SWITCHES ARE INOPERATIVE OR DO NOT OPERATE CORRECTLY : The Steering Wheel Controls Are Inoperative Or Do Not Operate Correctly. |
| B1D36:09 | Turn Indicator Switch: Component Failure | INSTALL a new multifunction switch. REFER to Steering Column Multifunction Switch
. TEST the system for normal operation. If the concern still exists, INSTALL a new SCCM. REFER to Steering Column Control Module (SCCM) . |
| C0051:09 | Steering Wheel Position Sensor: Component Failure | INSTALL a new steering wheel rotation sensor. REFER to STEERING WHEEL ROTATION SENSOR . |
| C0051:16 | Steering Wheel Position Sensor: Circuit Voltage Below Threshold | REFER to Diagnostic Routine L: C0051:16 or C0051:17 . |
| C0051:17 | Steering Wheel Position Sensor: Circuit Voltage Above Threshold | REFER to Diagnostic Routine L: C0051:16 or C0051:17 . |
| U1000:00 | Solid State Driver Protection Active-Driver Disabled: No Sub Type Information | This DTC is set when the SCCM activates one or more of the FET circuit protectors. This DTC will not clear until the concern that activated the FET has been repaired and the SCCM passes a self-test. REPAIR all other SCCM DTCs then CARRY OUT a SCCM on-demand self-test. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to incomplete or incorrect module programming, or due to an internal failure of the module. If the module has just recently been reprogrammed, attempt to PROGRAM the module again. RETRIEVE SCCM DTCs . If the DTC returns, INSTALL a new SCCM. REFER to Steering Column Control Module (SCCM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets if the steering wheel switches do not match the switch function configuration data in the SCCM. CHECK the part numbers in Ford Catalog Advantage™ or equivalent and CONFIRM the correct SCCM and steering wheel control switches are installed on the vehicle. |
| U3000:49 | Control Module: Internal Electronic Failure | INSTALL a new SCCM. REFER to Steering Column Control Module (SCCM) . |