Occupant Classification System Module (OCSM) (Bladder System)
DTC INDEX
| DTC | Description | Action To Take |
|---|---|---|
| B0061:11 | Passenger Seatbelt Tension Sensor: Circuit Short to Ground | GO to Pinpoint Test AH . |
| B0061:12 | Passenger Seatbelt Tension Sensor: Circuit Short to Battery | GO to Pinpoint Test AH . |
| B0061:13 | Passenger Seatbelt Tension Sensor: Circuit Open | GO to Pinpoint Test AH . |
| B0061:1C | Passenger Seatbelt Tension Sensor: Circuit Voltage Out of Range | GO to Pinpoint Test AH . |
| B0061:49 | Passenger Seatbelt Tension Sensor: Internal Electronic Failure | GO to Pinpoint Test AH . |
| B00C0:11 | Passenger Seat Occupant Classification Sensor "A": Circuit Short to Ground | INSPECT the OCS for any damage and for correct installation. If damage is found, REPAIR the root cause of the damage and INSTALL a new OCS, as necessary. REFER to Occupant Classification Sensor . If any installation concerns are found, CORRECT the OCS installation, referring to the OCS Removal and Installation procedure as needed to make sure the sensor hose is free from kinks and correctly routed. REFER to Occupant Classification Sensor . If no damage or installation concerns are found, INSTALL a new OCS. REFER to Occupant Classification Sensor . |
| B00C0:1A | Passenger Seat Occupant Classification Sensor "A": Circuit Resistance Below Threshold | INSTALL a new OCS sensor. REFER to Occupant Classification Sensor . |
| B00C0:49 | Passenger Seat Occupant Classification Sensor "A": Internal Electronic Failure | INSTALL a new OCS sensor. REFER to Occupant Classification Sensor . |
| B00C1:11 | Passenger Seat Occupant Classification Sensor "B": Circuit Short to Ground | INSTALL a new OCS sensor. REFER to Occupant Classification Sensor . |
| B00C1:12 | Passenger Seat Occupant Classification Sensor "B": Circuit Short to Battery | INSTALL a new OCS sensor. REFER to Occupant Classification Sensor . |
| B00C1:49 | Passenger Seat Occupant Classification Sensor "B": Internal Electronic Failure | INSTALL a new OCS sensor. REFER to Occupant Classification Sensor . |
| B00C2:11 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Ground | GO to Pinpoint Test AI . |
| B00C2:12 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Battery | GO to Pinpoint Test AI . |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | CLEAR the OCSM DTCs and REPEAT the self-test. If DTC B1193:00 returns, INSTALL a new OCS sensor. REFER to Occupant Classification Sensor . |
| U0100:00 | Lost Communication with ECM/PCM A: No Sub Type Information |
NOTE:
The DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair unless directed to do so in the pinpoint test. GO to Pinpoint Test AJ
. |
| U0151:00 | Lost Communication with Restraints Control Module: No Sub Type Information |
NOTE:
The DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair unless directed to do so in the pinpoint test. GO to Pinpoint Test AK
. |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | CARRY OUT the PCM self-test. REFER to the ENGINE CONTROLS - INTRODUCTION (EXCEPT DIESEL & HYBRID) or the PCM DTC chart in Electronic Engine Controls . |
| U3000:46 | Control Module: Calibration / Parameter Memory Failure | INSTALL a new OCS sensor. REFER to Occupant Classification Sensor . |
| U3000:49 | Control Module: Internal Electronic Failure | INSTALL a new OCS sensor. REFER to Occupant Classification Sensor . |
| U3000:54 | Control Module: Missing Calibration | Using a scan tool, CARRY OUT the OCS reset. FOLLOW all instructions on the scan tool. If the system reset was not successful, VERIFY correct installation of the OCS, VERIFY the pressure sensor hose is correctly routed and CORRECT the installation as necessary. REPEAT the system reset and REPEAT the self-test. If the system reset fails or DTC U3000:54 is still present, INSTALL a new OCS sensor. REFER to Occupant Classification Sensor . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AG . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AG . |