LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2015 >> Transit-350 HD Base, Van Cargo Extended >> Repair and Diagnosis >> Brakes >> Traction Control >> Anti-Lock Brake System Component Testing >> Pinpoint Tests >> Pinpoint Tests AY: ABS Module Communication Concern With IPC >> Possible Causes
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Possible Causes

  1. AY1: CHECK THE COMMUNICATION TO THE IPC 
    • Ignition ON, engine OFF.
    • Press the Read Vehicle Information button to view the results of the modules communicating on the network.
    • Retrieve the continuous memory DTCs.
    • Does the IPC and the GWM pass the network test? 
      Yes No
      Go to  AY2. REFER to MODULE COMMUNICATIONS NETWORK to diagnose the IPC or the GWM does not communicate with the diagnostic scan tool.
  2. AY2: RECHECK FOR THE ABS MODULE DTCS 
    • Carry out the ABS self-test.
    • Clear the ABS DTCs.
    • Ignition OFF.
    • Ignition ON, engine OFF.
    • Carry out the ABS self-test.
    • Record the ABS module DTCs.
    • Is DTC U0155:xx retrieved again? 
      Yes No
      Go to  AY3. The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.
  3. AY3: CHECK FOR VOLTAGE DTCS IN THE ABS MODULE 
    • Review the recorded DTCs from the ABS module self-test.
    • Is DTC U3003:16 or U3003:17 present? 
      Yes No
      For DTC U3003:17, Go to PINPOINT TEST F .
      For DTC U3003:16, Go to PINPOINT TEST A .      		 Go to  AY4.
  4. AY4: CHECK FOR VOLTAGE DTCS IN THE IPC 
  5. AY5: CHECK FOR VOLTAGE DTCS IN THE GWM 
    • Carry out the GWM self-test.
    • Record the DTCs from the GWM self-test.
    • Are any battery voltage DTCs present? 
      Yes No
      DIAGNOSE the GWM DTCs. REFER to MODULE COMMUNICATIONS NETWORK . Go to  AY6.
  6. AY6: CHECK FOR OTHER CAUSES OF COMMUNICATION NETWORK CONCERN 
    NOTE: If new modules were installed prior to the DTC being set, the module configuration can be incorrectly set during the PMI or the PMI may not have been carried out.
    • Check the vehicle service history for recent service actions related to the IPC or the ABS module. If recent service history is found:
      • Verify the correct replacement module was installed. HVBOM may be used to verify correct part fitment.
      • Verify the configuration of replacement module was correct. Re-configure the module using as-built data if prior configuration is suspect.
      • Verify the module was not obtained from a like vehicle and installed into customer vehicle. Return the swapped module to source vehicle and obtain new replacement module.
    • Operate the system and determine if the observable symptom is still present.
    • Is the observable symptom still present? 
      Yes No
      Go to  AY7. The system is operating correctly at this time. The concern may have been due to incorrect parts replacement procedures or incorrect module configuration.
  7. AY7: VERIFY ALL WIRING CONNECTIONS 
    • Ignition OFF.
    • Disconnect all IPC electrical connectors.
    • Disconnect the ABS module electrical connector.
    • Disconnect all in-line electrical connectors between the ABS module and the IPC.
    • Using a good light source, inspect all disconnected electrical connectors for the following:
      • corrosion - install new connector or terminal and clean the module pins
      • damaged or bent pins - install new terminals or pins
      • pushed-out pins - install new pins as necessary
      • spread terminals - install new terminals as necessary
    • Are the connectors free of corrosion, damaged pins, bent pins, pushed-out pins and spread terminals? 
      Yes No
      Go to  AY8. REPAIR the connector or terminals. Refer to OEM CONNECTOR REPAIR PROCEDURES , for schematic and connector information.
  8. AY8: CHECK FOR DTC U0155:XX SET IN OTHER MODULES 
    • Connect all in-line electrical connectors between the ABS module and the IPC. Make sure they seat and latch correctly.
    • Connect all IPC electrical connectors. Make sure they seat and latch correctly.
    • Connect the ABS module electrical connector. Make sure it seats and latches correctly.
    • Ignition ON, engine OFF.
    • Press the Read Vehicle Information button to view the results of the continuous DTCs set in other modules.
    • Retrieve the continuous memory DTCs.
    • Review the CMDTCs from all modules.
    • Is DTC U0155:xx set in other modules in addition to the ABS module? 
      Yes No
      CHECK OASIS for any applicable TSBs. If a TSB exists for this concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no TSBs address this concern, INSTALL a new IPC. INSTALL a new ABS module.
      CHECK OASIS for any applicable TSBs. If a TSB exists for this concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no TSBs address this concern, INSTALL a new ABS module.
scientia non olet · About LEMON Manuals