LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2015 >> Transit-350 HD Base, Van Cargo Extended >> Repair and Diagnosis >> Quick Lookups >> DTC Index >> Lane Keeping System >> IPMA
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Lane Keeping System: IPMA

DTC INDEX

DTC Description Action
C1001:78 Vision System Camera: Alignment or Adjustment Incorrect This DTC sets when the IPMA camera alignment is out of specification. PERFORM the camera alignment using a diagnostic scan tool.
B115E:54 Camera Module: Missing Calibration This DTC sets when a new IPMA has been installed without performing the camera alignment. PERFORM the camera alignment using a diagnostic scan tool.
B1385:67 Lane Keeping Aid System: Signal Incorrect After Event GO to Pinpoint Test D
U0001:88 High Speed CAN Communication Bus: Bus off A HS-CAN fault was present at a point in time. The fault is not currently present since the IPMA is communicating with the diagnostic scan tool. CLEAR the DTC and REPEAT the network test with the diagnostic scan tool. VERIFY the integrity of the connectors and wiring. Refer to Wiring Diagrams MODULE COMMUNICATIONS NETWORK for schematic and connector information.
U0100:82 Lost Communication With ECM/PCM "A": Alive/Sequence Counter Incorrect/Not Updated GO to Pinpoint Test F
U0121:00 Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information GO to Pinpoint Test G
U0121:82 Lost Communication With Anti-Lock Brake System (ABS) Control Module: Alive/Sequence Counter Incorrect/Not Updated GO to Pinpoint Test G
U0126:00 Lost Communication With Steering Angle Sensor Module: No Sub Type Information GO to Pinpoint Test H
U0140:00 Lost Communication With Body Control Module: No Sub Type Information GO to Pinpoint Test I
U0140:82 Lost Communication With Body Control Module: Alive/Sequence Counter Incorrect/Not Updated GO to Pinpoint Test I
U0151:00 Lost Communication With Restraints Control Module: No Sub Type Information GO to Pinpoint Test J
U0401:81 Invalid Data Received From ECM/PCM A: Invalid Serial Data Received This DTC sets when the IPMA receives invalid network data from the PCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom.
U0402:81 Invalid Data Received From TCM: Invalid Serial Data Received This DTC sets when the IPMA receives invalid network data from the PCM (gasoline vehicles) or TCM (diesel vehicles) with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM (gasoline vehicles) or TCM (diesel vehicles). If no Diagnostic Trouble Codes (DTCs) are present in the PCM (gasoline vehicles) or TCM (diesel vehicles), DIAGNOSE the observable symptom.
U0415:00 Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information This DTC sets when the IPMA receives invalid network data from the ABS module with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the ABS module. If no Diagnostic Trouble Codes (DTCs) are present in the ABS module, DIAGNOSE the observable symptom.
U0422:00 Invalid Data Received From Body Control Module: No Sub Type Information This DTC sets when the IPMA receives invalid network data from the BCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM. If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom.
U0422:81 Invalid Data Received From Body Control Module: Invalid Serial Data Received This DTC sets when the IPMA receives invalid network data from the BCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM. If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom.
U0423:00 Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information This DTC sets when the IPMA receives invalid network data from the IPC with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the IPC. If no Diagnostic Trouble Codes (DTCs) are present in the IPC, DIAGNOSE the observable symptom.
U0423:81 Invalid Data Received From Instrument Panel Cluster Control Module: Invalid Serial Data Received This DTC sets when the IPMA receives invalid network data from the IPC with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the IPC. If no Diagnostic Trouble Codes (DTCs) are present in the IPC, DIAGNOSE the observable symptom.
U0428:00 Invalid Data Received From Steering Angle Sensor Module: No Sub Type Information This DTC sets when the IPMA receives invalid network data from the SASM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the SASM. If no Diagnostic Trouble Codes (DTCs) are present in the SASM, DIAGNOSE the observable symptom.
U0428:83 Invalid Data Received From Steering Angle Sensor Module: Value of Signal Protection Calculation Incorrect This DTC sets when the IPMA receives invalid network data from the SASM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the SASM. If no Diagnostic Trouble Codes (DTCs) are present in the SASM, DIAGNOSE the observable symptom.
U0452:00 Invalid Data Received From Restraints Control Module: No Sub Type Information This DTC sets when the IPMA receives invalid network data from the RCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the RCM. If no Diagnostic Trouble Codes (DTCs) are present in the RCM, DIAGNOSE the observable symptom.
U2100:00 Initial Configuration Not Complete: No Sub Type Information CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description If there have been no recent service actions, INSTALL a new IPMA to correct the failure to retain configuration data. REFER to: Image Processing Module A (IPMA)
U2101:00 Control Module Configuration Incompatible: No Sub Type Information CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description If there have been no recent service actions, INSTALL a new IPMA to correct the failure to retain configuration data. REFER to: Image Processing Module A (IPMA)
U3000:00 Control Module: No Sub Type Information CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the IPMA self test. If the DTC returns, INSTALL a new IPMA. REFER to: Image Processing Module A (IPMA)
scientia non olet · About LEMON Manuals