Anti-Lock Brake System (Abs) Module
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B10DF:46 | Master Cylinder Isolation Valve: Calibration / Parameter Memory Failure | This DTC sets due to an internal failure of the ABS module or a calibration failure between the HCU and the ABS module. Using a diagnostic scan tool, CARRY OUT all 3 of the following calibration routines in the order listed: Inlet Valve Calibration, Master Cylinder Isolation Calibration and Multi-Calibration. CLEAR the DTC and REPEAT the self-test. If the DTC returns, REPEAT all 3 calibration routines making sure to FOLLOW the diagnostic scan tool directions. CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0001:01 | TCS Control Channel "A" Valve 1: General Electrical Failure | This DTC indicates that part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C0002:01 | TCS Control Channel "A" Valve 2: General Electrical Failure | This DTC indicates that part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C0003:01 | TCS Control Channel "B" Valve 1: General Electrical Failure | This DTC indicates that part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C0004:01 | TCS Control Channel "B" Valve 2: General Electrical Failure | This DTC indicates that part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C0010:01 | Left Front Inlet Control: General Electrical Failure | This DTC indicates that part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0011:01 | Left Front Outlet Control: General Electrical Failure | This DTC indicates that part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0014:01 | Right Front Inlet Control: General Electrical Failure | This DTC indicates that part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0015:01 | Right Front Outlet Control: General Electrical Failure | This DTC indicates that part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0018:01 | Left Rear Inlet Control: General Electrical Failure | This DTC indicates that part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0019:01 | Left Rear Outlet Control: General Electrical Failure | This DTC indicates that part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C001C:01 | Right Rear Inlet Control: General Electrical Failure | This DTC indicates that part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C001D:01 | Right Rear Outlet Control: General Electrical Failure | This DTC indicates that part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0020:11 | ABS Pump Motor Control: Circuit Short To Ground | This DTC indicates that part of the ABS module has failed internally. CLEAR the DTC. REPEAT the ABS module self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C0020:12 | ABS Pump Motor Control: Circuit Short To Battery | GO to Pinpoint Test H |
| C0020:13 | ABS Pump Motor Control: Circuit Open | GO to Pinpoint Test H |
| C0020:71 | ABS Pump Motor Control: Actuator Stuck | GO to Pinpoint Test H |
| C0021:21 | Brake Booster Performance: Signal Amplitude < Minimum | GO to Pinpoint Test N |
| C0021:66 | Brake Booster Performance: Signal Has Too Many Transitions / Events | GO to Pinpoint Test N |
| C0021:77 | Brake Booster Performance: Commanded Position Not Reachable | GO to Pinpoint Test N |
| C0022:01 | Brake Booster Solenoid: General Electrical Failure | GO to Pinpoint Test J |
| C0022:11 | Brake Booster Solenoid: Circuit Short To Ground | GO to Pinpoint Test J |
| C0022:12 | Brake Booster Solenoid: Circuit Short To Battery | GO to Pinpoint Test J |
| C0022:49 | Brake Booster Solenoid: Internal Electronic Failure | GO to Pinpoint Test J |
| C0030:07 | Left Front Tone Wheel: Mechanical Failure | GO to Pinpoint Test B |
| C0031:07 | Left Front Wheel Speed Sensor: Mechanical Failure | GO to Pinpoint Test B |
| C0031:11 | Left Front Wheel Speed Sensor: Circuit Short to Ground | GO to Pinpoint Test O |
| C0031:15 | Left Front Wheel Speed Sensor: Circuit Short to Battery or Open | GO to Pinpoint Test O |
| C0031:29 | Left Front Wheel Speed Sensor: Signal Invalid | GO to Pinpoint Test B |
| C0031:2F | Left Front Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test B |
| C0031:4A | Left Front Wheel Speed Sensor: Incorrect Component Installed | DIAGNOSE all other wheel speed sensor Diagnostic Trouble Codes (DTCs) before diagnosing any
"Incorrect Component Installed" wheel speed sensor Diagnostic Trouble Codes (DTCs). This DTC sets when the incorrect type of wheel speed sensor has been installed, bi-directional versus non-bi-directional. For information on wheel speed sensor types, REFER to: Anti-Lock Brake System (ABS) and Stability Control - System Operation and Component Description . INSTALL a new wheel speed sensor. REFER to: Front Wheel Speed Sensor . |
| C0031:64 | Left Front Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test B |
| C0033:07 | Right Front Tone Wheel: Mechanical Failure | GO to Pinpoint Test B |
| C0034:07 | Right Front Wheel Speed Sensor: Mechanical Failure | GO to Pinpoint Test B |
| C0034:11 | Right Front Wheel Speed Sensor: Circuit Short to Ground | GO to Pinpoint Test O |
| C0034:15 | Right Front Wheel Speed Sensor: Circuit Short to Battery or Open | GO to Pinpoint Test O |
| C0034:29 | Right Front Wheel Speed Sensor: Signal Invalid | GO to Pinpoint Test B |
| C0034:2F | Right Front Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test B |
| C0034:4A | Right Front Wheel Speed Sensor: Incorrect Component Installed | DIAGNOSE all other wheel speed sensor Diagnostic Trouble Codes (DTCs) before diagnosing any
"Incorrect Component Installed" wheel speed sensor Diagnostic Trouble Codes (DTCs). This DTC sets when the incorrect type of wheel speed sensor has been installed, bi-directional versus non-bi-directional. For information on wheel speed sensor types, REFER to: Anti-Lock Brake System (ABS) and Stability Control - System Operation and Component Description . INSTALL a new wheel speed sensor. REFER to: Front Wheel Speed Sensor . |
| C0034:64 | Right Front Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test B |
| C0036:07 | Left Rear Tone Wheel: Mechanical Failure | GO to Pinpoint Test B |
| C0037:07 | Left Rear Wheel Speed Sensor: Mechanical Failure | GO to Pinpoint Test B |
| C0037:11 | Left Rear Wheel Speed Sensor: Circuit Short to Ground | GO to Pinpoint Test P |
| C0037:15 | Left Rear Wheel Speed Sensor: Circuit Short to Battery or Open | GO to Pinpoint Test P |
| C0037:29 | Left Rear Wheel Speed Sensor: Signal Invalid | GO to Pinpoint Test B |
| C0037:2F | Left Rear Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test B |
| C0037:4A | Left Rear Wheel Speed Sensor: Incorrect Component Installed | This DTC sets when the incorrect type of wheel speed sensor has been installed, bi-directional versus non-bi-directional. For information on wheel speed sensor types, REFER to: Anti-Lock Brake System (ABS) and Stability Control - System Operation and Component Description
. DIAGNOSE DTC U2100:00 and all other wheel speed sensor Diagnostic Trouble Codes (DTCs) before diagnosing any "Incorrect Component Installed" wheel speed sensor Diagnostic Trouble Codes (DTCs). If there are no other ABS module Diagnostic Trouble Codes (DTCs) present, INSTALL a new wheel speed sensor. REFER to: Rear Wheel Speed Sensor . |
| C0037:64 | Left Rear Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test B |
| C0039:07 | Right Rear Tone Wheel: Mechanical Failure | GO to Pinpoint Test B |
| C003A:07 | Right Rear Wheel Speed Sensor: Mechanical Failure | GO to Pinpoint Test B |
| C003A:11 | Right Rear Wheel Speed Sensor: Circuit Short to Ground | GO to Pinpoint Test P |
| C003A:15 | Right Rear Wheel Speed Sensor: Circuit Short to Battery or Open | GO to Pinpoint Test P |
| C003A:29 | Right Rear Wheel Speed Sensor: Signal Invalid | GO to Pinpoint Test B |
| C003A:2F | Right Rear Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test B |
| C003A:4A | Right Rear Wheel Speed Sensor: Incorrect Component Installed | This DTC sets when the incorrect type of wheel speed sensor has been installed, bi-directional versus non-bi-directional. For information on wheel speed sensor types, REFER to: Anti-Lock Brake System (ABS) and Stability Control - System Operation and Component Description
. DIAGNOSE DTC U2100:00 and all other wheel speed sensor Diagnostic Trouble Codes (DTCs) before diagnosing any "Incorrect Component Installed" wheel speed sensor Diagnostic Trouble Codes (DTCs). If there are no other ABS module Diagnostic Trouble Codes (DTCs) present, INSTALL a new wheel speed sensor. REFER to: Rear Wheel Speed Sensor . |
| C003A:64 | Right Rear Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test B |
| C0040:64 | Brake Pedal Switch "A": Signal Plausibility Failure | GO to Pinpoint Test C |
| C0044:28 | Brake Pressure Sensor "A": Signal Bias Level Out of Range / Zero Adjustment Failure | GO to Pinpoint Test C |
| C0044:47 | Brake Pressure Sensor "A": Watchdog / Safety Failure | DIAGNOSE DTC C0040:64 before diagnosing this DTC. If DTC C0040:64 is not present, CLEAR the DTC. CYCLE the ignition from ON to OFF and back to ON. REPEAT the self-test. If DTC C0044:47 returns, VERIFY all ABS module-to- HCU fasteners are tightened to 2 NM (18 lb-in). If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C0044:49 | Brake Pressure Sensor "A": Internal Electronic Failure | DIAGNOSE DTC C0040:64 before diagnosing this DTC. If DTC C0040:64 is not present, CLEAR the DTC. CYCLE the ignition from ON to OFF and back to ON. REPEAT the self-test. If DTC C0044:49 returns, VERIFY all ABS module-to- HCU fasteners are tightened to 2 NM (18 lb-in). If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C0044:51 | Brake Pressure Sensor "A": Not Programmed | DIAGNOSE DTC C0040:64 before diagnosing this DTC. If DTC C0040:64 is not present, CLEAR the DTC. CYCLE the ignition from ON to OFF and back to ON. REPEAT the self-test. If DTC C0044:51 returns, VERIFY all ABS module-to- HCU fasteners are tightened to 2 NM (18 lb-in). If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C0044:64 | Brake Pressure Sensor "A": Signal Plausibility Failure | DIAGNOSE DTC C0040:64 before diagnosing this DTC. If DTC C0040:64 is not present, CLEAR the DTC. CYCLE the ignition from ON to OFF and back to ON. REPEAT the self-test. If DTC C0044:64 returns, VERIFY all ABS module-to- HCU fasteners are tightened to 2 NM (18 lb-in). If all fasteners are tightened to their correct torque specifications, INSPECT the brake tubes and connections for damage and leaks. REPAIR or INSTALL new brake tubes as necessary. If brake tubes and connections are OK and there are no brake fluid leaks, BLEED the brake system. REFER to: Brake System Pressure Bleeding . CYCLE the ignition from ON to OFF and back to ON. CARRY OUT the ABS module self-test. If this DTC returns, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C0044:8F | Brake Pressure Sensor "A": Erratic | DIAGNOSE DTC C0040:64 before diagnosing this DTC. If DTC C0040:64 is not present, CLEAR the DTC. CYCLE the ignition from ON to OFF and back to ON. REPEAT the self-test. If DTC C0044:8F returns, VERIFY all ABS module-to- HCU fasteners are tightened to 2 NM (18 lb-in). If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C0047:01 | Brake Booster Pressure Sensor: General Electric Failure | GO to Pinpoint Test R |
| C0047:1B | Brake Booster Pressure Sensor: Circuit Resistance Above Threshold | GO to Pinpoint Test R |
| C0047:26 | Brake Booster Pressure Sensor: Signal Rate of Change Below Threshold | GO to Pinpoint Test R |
| C0047:27 | Brake Booster Pressure Sensor: Signal Rate of Change Above Threshold | GO to Pinpoint Test R |
| C0047:62 | Brake Booster Pressure Sensor: Signal Compare Failure | GO to Pinpoint Test R |
| C0048:11 | Brake Booster Travel Sensor: Circuit Short to Ground | GO to Pinpoint Test Q |
| C0048:12 | Brake Booster Travel Sensor: Circuit Short to Battery | GO to Pinpoint Test Q |
| C0048:64 | Brake Booster Travel Sensor: Signal Plausibility Failure | GO to Pinpoint Test Q |
| C0051:28 | Steering Wheel Position Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure | GO to Pinpoint Test M |
| C0051:54 | Steering Wheel Position Sensor: Missing Calibration | GO to Pinpoint Test M |
| C0051:62 | Steering Wheel Position Sensor: Signal Compare Failure | GO to Pinpoint Test M |
| C0051:64 | Steering Wheel Position Sensor: Signal Plausibility Failure | GO to Pinpoint Test M |
| C0051:85 | Steering Wheel Position Sensor: Signal Above Allowable Range | GO to Pinpoint Test M |
| C0051:96 | Steering Wheel Position Sensor: Component Internal Failure | GO to Pinpoint Test M |
| C0061:28 | Lateral Acceleration Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure | GO to Pinpoint Test G |
| C0061:2F | Lateral Acceleration Sensor: Signal Erratic | GO to Pinpoint Test G |
| C0061:64 | Lateral Acceleration Sensor: Signal Plausibility Failure | GO to Pinpoint Test G |
| C0062:28 | Longitudinal Acceleration Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure | GO to Pinpoint Test G |
| C0062:54 | Longitudinal Acceleration Sensor: Missing Calibration | This DTC sets if the stability sensors in the RCM have not been calibrated or the calibration has been lost. CARRY OUT the IVD Initialization routine, FOLLOW the diagnostic scan tool instructions. If the module fails the routine, VERIFY the RCM is installed correctly and the fasteners are tightened to specifications. REINSTALL the RCM or INSTALL new fasteners as necessary. REFER to: Restraints Control Module (RCM) . If the RCM is OK, CARRY OUT the RCM self-test. RETRIEVE and RECORD any Diagnostic Trouble Codes (DTCs). REFER to: Airbag Supplemental Restraint System (SRS) . If the module passes the routine, CLEAR the DTC. CYCLE the ignition from ON to OFF and back to ON. CARRY OUT the ABS module self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0062:64 | Longitudinal Acceleration Sensor: Signal Plausibility Failure | GO to Pinpoint Test G |
| C0062:76 | Longitudinal Acceleration Sensor: Wrong Mounting Position | Due to the nature of the longitudinal acceleration sensor, the RCM must be installed in the correct orientation to the centerline of the vehicle. This DTC sets if the RCM has been installed in the wrong position. VERIFY the RCM is installed correctly and the fasteners are tightened to specifications. REINSTALL the RCM or INSTALL new fasteners as necessary. REFER to: Restraints Control Module (RCM) . If the RCM is OK, CARRY OUT the RCM self-test. RETRIEVE and RECORD any Diagnostic Trouble Codes (DTCs). REFER to: Airbag Supplemental Restraint System (SRS) . |
| C0063:28 | Yaw Rate Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure | GO to Pinpoint Test G |
| C0063:2F | Yaw Rate Sensor: Signal Erratic | GO to Pinpoint Test G |
| C0063:64 | Yaw Rate Sensor: Signal Plausibility Failure | GO to Pinpoint Test G |
| C0064:28 | Roll Rate Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure | GO to Pinpoint Test G |
| C0064:64 | Roll Rate Sensor: Signal Plausibility Failure | GO to Pinpoint Test G |
| C006B:00 | Stability System Active Too Long: No Sub Type Information | GO to Pinpoint Test W |
| C100A:28 | Brake Pedal Angle Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure | The brake pedal angle sensor is also known as the brake pedal travel sensor. This DTC indicates the brake pedal angle sensor does not reach the fully released position. This can be caused by damage or changes to the brake pedal and bracket assembly or an internal failure of the sensor. INSPECT the brake pedal and bracket assembly for any mechanical damage or foreign objects that may be restricting pedal movement. REPAIR as necessary. If the brake pedal and bracket are free of any mechanical damage or foreign objects, INSTALL a new brake pedal angle sensor. REFER to: Brake Pedal Travel Sensor . |
| C100A:41 | Brake Pedal Angle Sensor: General Checksum Failure | This DTC indicates that part of the ABS module has failed internally. CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C100A:62 | Brake Pedal Angle Sensor: Signal Compare Failure | GO to Pinpoint Test S |
| C100A:64 | Brake Pedal Angle Sensor: Signal Plausibility Failure | GO to Pinpoint Test S |
| C100D:21 | Brake Pedal Angle Sensor Circuit 1: Signal Amplitude < Minimum | GO to Pinpoint Test S |
| C100D:22 | Brake Pedal Angle Sensor Circuit 1: Signal Amplitude > Maximum | GO to Pinpoint Test S |
| C100D:38 | Brake Pedal Angle Sensor Circuit 1: Signal Frequency Incorrect | GO to Pinpoint Test S |
| C100E:21 | Brake Pedal Angle Sensor Circuit 2: Signal Amplitude < Minimum | GO to Pinpoint Test S |
| C100E:22 | Brake Pedal Angle Sensor Circuit 2: Signal Amplitude > Maximum | GO to Pinpoint Test S |
| C100E:38 | Brake Pedal Angle Sensor Circuit 2: Signal Frequency Incorrect | GO to Pinpoint Test S |
| C100F:11 | Brake Pedal Angle Sensor Supply: Circuit Short To Ground | GO to Pinpoint Test S |
| C100F:12 | Brake Pedal Angle Sensor Supply: Circuit Short To Battery | GO to Pinpoint Test S |
| C1013:00 | Brake System Pressure: No Sub-Type Information | This DTC sets when the overall brake system pressure deviates from one or more wheel pressures or the front wheel pressures do not match each other. RETRIEVE all ABS Diagnostic Trouble Codes (DTCs). DIAGNOSE DTC C0044:xx, C1133:xx or C1134:xx before diagnosing C1013:00. If DTC C0044:xx, C1133:xx or C1134:xx is not present, INSPECT the brake stem for fluid leaks and the brake tubes and hoses for any damage. REPAIR as necessary. |
| C1014:07 | Brake System Total Volume Balance: Mechanical Failure | This DTC sets as a result of brake pads or brake discs worn down to or below minimum thickness, a brake booster travel sensor fault, a brake fluid pressure sensor fault or air trapped in the hydraulic brake system. DIAGNOSE all codes indicating a brake booster travel sensor fault or a hydraulic brake pressure sensor fault. If only DTC C1014:07 is present, VERIFY brake pads and brake discs are above the minimum thickness, REFER to: Specifications . CLEAR the DTC and REPEAT the self-test. If DTC C1014:07 returns, BLEED the brake system. REFER to: Brake System Pressure Bleeding . CLEAR the DTC and REPEAT the self-test. If DTC C1014:07 returns, INSTALL a new brake booster. REFER to: Brake Booster . |
| C1015:64 | Vacuum Supply: Signal Plausibility Failure | GO to Pinpoint Test X |
| C1015:7A | Vacuum Supply: Fluid Leak or Seal Failure | GO to Pinpoint Test X |
| C1015:7B | Vacuum Supply: Low Fluid Level | GO to Pinpoint Test X |
| C1018:46 | Regenerative Braking: Calibration / Parameter Memory Failure | GO to Pinpoint Test Y |
| C101C:01 | Brake Vacuum Pump: General Electrical Failure | GO to Pinpoint Test T |
| C1020:00 | Brake System Fill Not Complete: No Sub-Type Information | This DTC is pre-set in a new ABS module and can only be cleared after the brake system has been successfully bled. BLEED the brake system. REFER to: Brake System Pressure Bleeding . |
| C1021:21 | ABS Booster Control Pressure: Signal Amplitude < Minimum | GO to Pinpoint Test Z |
| C1021:22 | ABS Booster Control Pressure: Signal Amplitude > Maximum | GO to Pinpoint Test Z |
| C1025:21 | Brake Primary Circuit Overboost Pressure: Signal Amplitude < Minimum | INSPECT the brake system for brake fluid leaks. REPAIR as necessary. If no leaks are found, BLEED the brake system. REFER to: Brake System Pressure Bleeding
. CLEAR the DTC and REPEAT the self-test. If DTC C1025:21 returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C1026:21 | ABS Secondary Circuit Overboost Pressure: Signal Amplitude < Minimum | INSPECT the brake system for brake fluid leaks. REPAIR as necessary. If no leaks are found, BLEED the brake system. REFER to: Brake System Pressure Bleeding
. CLEAR the DTC and REPEAT the self-test. If DTC C1026:21 returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C1027:62 | Master Cylinder (MC) to Primary Circuit Pressure: Signal Compare Failure | INSPECT the brake system for brake fluid leaks. REPAIR as necessary. If no leaks are found, BLEED the brake system. REFER to: Brake System Pressure Bleeding
. CLEAR the DTC and REPEAT the self-test. If DTC C1027:62 returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C1029:00 | ABS Primary Circuit Lower Than Secondary: No Sub-Type Information | GO to Pinpoint Test U |
| C102B:00 | ABS Secondary Circuit Lower Than Primary: No Sub-Type Information | GO to Pinpoint Test U |
| C1035:01 | Vacuum Pump Relay 1: General Electrical Failure | GO to Pinpoint Test T |
| C1036:01 | Vacuum Pump Relay 2: General Electrical Failure | GO to Pinpoint Test T |
| C1133:28 | Left Front Brake Pressure Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure | CLEAR the DTC and REPEAT the self-test. If DTC C1133:28 returns, make sure all ABS module-to- HCU fasteners are tightened to their correct torque specifications. If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C1133:47 | Left Front Brake Pressure Sensor: Watchdog / Safety Failure | CLEAR the DTC and REPEAT the self-test. If DTC C1133:47 returns, make sure all ABS module-to- HCU fasteners are tightened to their correct torque specifications. If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C1133:49 | Left Front Brake Pressure Sensor: Internal Electronic Failure | CLEAR the DTC and REPEAT the self-test. If DTC C1133:49 returns, make sure all ABS module-to- HCU fasteners are tightened to their correct torque specifications. If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C1133:51 | Left Front Brake Pressure Sensor: Not Programmed | CLEAR the DTC and REPEAT the self-test. If DTC C1133:51 returns, make sure all ABS module-to- HCU fasteners are tightened to their correct torque specifications. If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C1133:64 | Left Front Brake Pressure Sensor: Signal Plausibility Failure | CLEAR the DTC and REPEAT the self-test. If DTC C1133:64 returns, make sure all ABS module-to- HCU fasteners are tightened to their correct torque specifications. If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C1133:8F | Left Front Brake Pressure Sensor: Erratic | CLEAR the DTC and REPEAT the self-test. If DTC C1133:8F returns, make sure all ABS module-to- HCU fasteners are tightened to their correct torque specifications. If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C1134:28 | Right Front Brake Pressure Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure | CLEAR the DTC and REPEAT the self-test. If DTC C1134:28 returns, make sure all ABS module-to- HCU fasteners are tightened to their correct torque specifications. If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C1134:47 | Right Front Brake Pressure Sensor: Watchdog / Safety Failure | CLEAR the DTC and REPEAT the self-test. If DTC C1134:47 returns, make sure all ABS module-to- HCU fasteners are tightened to their correct torque specifications. If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C1134:49 | Right Front Brake Pressure Sensor: Internal Electronic Failure | CLEAR the DTC and REPEAT the self-test. If DTC C1134:49 returns, make sure all ABS module-to- HCU fasteners are tightened to their correct torque specifications. If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C1134:51 | Right Front Brake Pressure Sensor: Not Programmed | CLEAR the DTC and REPEAT the self-test. If DTC C1134:51 returns, make sure all ABS module-to- HCU fasteners are tightened to their correct torque specifications. If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C1134:64 | Right Front Brake Pressure Sensor: Signal Plausibility Failure | CLEAR the DTC and REPEAT the self-test. If DTC C1134:64 returns, make sure all ABS module-to- HCU fasteners are tightened to their correct torque specifications. If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C1134:8F | Right Front Brake Pressure Sensor: Erratic | CLEAR the DTC and REPEAT the self-test. If DTC C1134:8F returns, make sure all ABS module-to- HCU fasteners are tightened to their correct torque specifications. If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C1137:64 | Reverse Gear Switch: Signal Plausibility Failure | This DTC sets when the transmission gear selection message sent from the TCM does not match other inputs received by the ABS module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the TCM. REFER to: Automatic Transmission - Hybrid Electric Vehicle (HEV) . REFER to: Automatic Transmission - Plug-In Hybrid Electric Vehicle (PHEV) . |
| C1A08:1C | Pressure Sensor Supply: Circuit Voltage Out of Range | The brake system pressure sensor is supplied voltage by the ABS module. The ABS module monitors this output and sets this DTC when the voltage is out of range. DIAGNOSE DTC U3003:16 or U3003:17, before diagnosing C1A08:1C. If DTC U3003:16 or U3003:17 is not present, make sure all ABS module-to- HCU fasteners are tightened to their correct torque specifications. If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| C1B14:11 | Sensor Supply Voltage "A": Circuit Short to Ground | GO to Pinpoint Test R |
| C1B14:12 | Sensor Supply Voltage "A": Circuit Short to Battery | GO to Pinpoint Test R |
| C1B15:1C | Sensor Supply Voltage "B": Circuit Voltage Out of Range | GO to Pinpoint Test R |
| P0942:46 | Hydraulic Pressure Unit: Calibration / Parameter Memory Failure | The ABS module and HCU are calibrated to one another and should not be swapped between different vehicles. This DTC sets when the identification data stored in the ABS module does not match the identification data from the HCU. Using a diagnostic scan tool, CARRY OUT the Inlet Valve Calibration routine, then the Master Cylinder Isolation Calibration routine and then the Multi-Calibration routine. CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . |
| P0942:49 | Hydraulic Pressure Unit: Internal Electronic Failure | The ABS module and HCU are calibrated to one another and should not be swapped between different vehicles. This DTC sets when the identification data stored in the ABS module does not match the identification data from the HCU. Using a diagnostic scan tool, CARRY OUT the Inlet Valve Calibration routine, then the Master Cylinder Isolation Calibration routine and then the Multi-Calibration routine. CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . |
| P193B:86 | Throttle / Pedal Signal: Signal Invalid | GO to Pinpoint Test I |
| U0001:88 | High Speed CAN Communication Bus: Bus Off | HS-CAN fault was present at a point in time. The fault is not currently present since the module is communicating with the diagnostic scan tool. CLEAR the DTC. REPEAT the Network Test with the diagnostic scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
| U0028:88 | Vehicle Communication Bus "A": Bus Off | GO to Pinpoint Test G |
| U0100:00 | Lost Communication With ECM / PCM "A": No Sub Type Information | GO to Pinpoint Test I |
| U0100:87 | Lost Communication With ECM / PCM "A": Missing Message | GO to Pinpoint Test I |
| U0126:00 | Lost Communication With Steering Angle Sensor Module: No Sub Type Information | GO to Pinpoint Test K |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test D |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test G |
| U0293:00 | Lost Communication with Hybrid / EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test AA |
| U0300:51 | Internal Control Module Software Incompatibility: Not Programmed | CHECK vehicle service history for recent service actions related to the ABS module. This DTC sets due to incomplete or improper flash programming procedures. If there have been recent service actions with the ABS module, REPEAT the programming procedure as directed by the diagnostic scan tool. |
| U0401:00 | Invalid Data Received From ECM / PCM "A": No Sub Type Information | This DTC sets when the ABS module receives invalid network data from the PCM. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all PCM and GWM Diagnostic Trouble Codes (DTCs). REFER to: MODULE COMMUNICATIONS NETWORK . REFER to: ELECTRONIC ENGINE CONTROLS SYSTEM - 2.0L DURATEC - HYBRID (96KW/130PS) . If the diagnostic scan tool cannot communicate with the PCM or GWM, REFER to: MODULE COMMUNICATIONS NETWORK . If there are no Diagnostic Trouble Codes (DTCs) in the PCM or GWM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all PCM and GWM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0401:08 | Invalid Data Received From ECM / PCM "A": Bus Signal / Message Failure | This DTC sets if the ABS module receives invalid data in the driven wheel propulsion torque request message. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all PCM and GWM Diagnostic Trouble Codes (DTCs). REFER to: MODULE COMMUNICATIONS NETWORK . REFER to: ELECTRONIC ENGINE CONTROLS SYSTEM - 2.0L DURATEC - HYBRID (96KW/130PS) . If the diagnostic scan tool cannot communicate with the PCM or GWM, REFER to: MODULE COMMUNICATIONS NETWORK . If there are no Diagnostic Trouble Codes (DTCs) in the PCM or GWM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all PCM and GWM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | This DTC sets when the ABS module receives invalid network data from the BCM. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all BCM and GWM Diagnostic Trouble Codes (DTCs). REFER to: MODULE COMMUNICATIONS NETWORK . REFER to: Body Control Module (BCM) . If the diagnostic scan tool cannot communicate with the BCM or GWM, REFER to: MODULE COMMUNICATIONS NETWORK . If there are no Diagnostic Trouble Codes (DTCs) in the BCM or GWM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all BCM and GWM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0428:41 | Invalid Data Received From Steering Angle Sensor Module: General Checksum Failure | If DTC U0126:00 is present, DIAGNOSE DTC U0126:00 first. This DTC sets when the ABS module receives invalid network data from the SASM. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all SASM Diagnostic Trouble Codes (DTCs). REFER to the STEERING ANGLE SENSOR MODULE (SASM) . If the diagnostic scan tool cannot communicate with the SASM, REFER to:MODULE COMMUNICATIONS NETWORK . If there are no Diagnostic Trouble Codes (DTCs) in the SASM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all SASM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0428:82 | Invalid Data Received From Steering Angle Sensor Module: Alive / Sequence Counter Incorrect / Not Updated | If DTC U0126:00 is present, DIAGNOSE DTC U0126:00 first. This DTC sets when the ABS module receives invalid network data from the SASM. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all SASM Diagnostic Trouble Codes (DTCs). REFER to the STEERING ANGLE SENSOR MODULE (SASM) . If the diagnostic scan tool cannot communicate with the SASM, REFER to: MODULE COMMUNICATIONS NETWORK . If there are no Diagnostic Trouble Codes (DTCs) in the SASM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all SASM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0452:41 | Invalid Data Received From Restraints Control Module: General Checksum Failure | This DTC sets when the ABS module receives invalid network data from the RCM. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all RCM Diagnostic Trouble Codes (DTCs). REFER to: Airbag Supplemental Restraint System (SRS) . If the diagnostic scan tool cannot communicate with the RCM, REFER to: COMMUNICATIONS NETWORK . If there are no Diagnostic Trouble Codes (DTCs) in the RCM, the DTC may be caused by an intermittent concern. SET the ignition to OFF and WAIT one minute. DISCONNECT and INSPECT all RCM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0452:86 | Invalid Data Received From Restraints Control Module: Signal Invalid | GO to Pinpoint Test G |
| U0594:00 | Invalid Data Received From Hybrid / EV Powertrain Control Module: No Sub Type Information | This DTC sets when the ABS module receives invalid network data from the SOBDMC. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all SOBDMC and GWM Diagnostic Trouble Codes (DTCs). REFER to: MODULE COMMUNICATIONS NETWORK . REFER to: ELECTRONIC ENGINE CONTROLS SYSTEM - 2.0L DURATEC - HYBRID (96KW/130PS) . If the diagnostic scan tool cannot communicate with the SOBDMC or GWM, REFER to: MODULE COMMUNICATIONS NETWORK . If there are no Diagnostic Trouble Codes (DTCs) in the SOBDMC or GWM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all SOBDMC and GWM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U2007:46 | Valve(s): Calibration / Parameter Memory Failure | This DTC sets due to an internal failure of the ABS module or a calibration failure between the HCU and the ABS module. Using a diagnostic scan tool, CARRY OUT the Inlet Valve Calibration routine, then the Master Cylinder Isolation Calibration routine and then the Multi-Calibration routine. CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| U2007:62 | Valve(s): Signal Compare Failure | This DTC sets due to an internal failure of the ABS module or a calibration failure between the HCU and the ABS module. CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| U2024:51 | Control Module Cal-Config Data: Not Programmed | This DTC is only present when a new ABS module is installed, the ABS module is flashed or the ABS module is reconfigured. Using a diagnostic scan tool, CONFIGURE the ABS module. FOLLOW all diagnostic scan tool instructions. REFER to: Module Configuration - System Operation and Component Description . Using a diagnostic scan tool, CARRY OUT the ABS module self-test to clear the DTC. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC is pre-set in a new ABS module and clears automatically when the ABS module is configured correctly. CHECK the service history for recent service actions related to the ABS module. This DTC sets due to incomplete or improper PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure using as-built data. If there have been no recent service actions, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | CHECK the service history for recent service actions related to the ABS module. This DTC sets due to incomplete or improper PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the diagnostic scan tool. If there have been no recent service actions, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| U3000:49 | Control Module: Internal Electronic Failure | CLEAR the Diagnostic Trouble Codes (DTCs). CARRY OUT the ABS module self-test. RETRIEVE and RECORD all Diagnostic Trouble Codes (DTCs). If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . Using a diagnostic scan tool, CLEAR the SOBDMC Diagnostic Trouble Codes (DTCs). |
| U3002:62 | Vehicle Identification Number: Signal Compare Failure | GO to Pinpoint Test V |
| U3003:08 | Battery Voltage: Bus Signal / Message Failure | This DTC sets when the HS-CAN is shorted together, shorted to ground, shorted to voltage or open. If DTC U3003:16 is present, DIAGNOSE DTC U3003:16 before diagnosing DTC U3003:08. If DTC U3003:16 is not present, REFER to: MODULE COMMUNICATIONS NETWORK . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test A |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test F |
| U300A:29 | Ignition Switch: Signal Invalid | GO to Pinpoint Test A |