| P0218 |
Transmission Fluid Temperature Sensor "A" Over Temperature Condition |
If any TFT sensor circuit diagnostic trouble codes (DTCs) are present, RESOLVE those first. Otherwise, CLEAR the DTC and road test the vehicle. If DTC P0218 returns, diagnose the transmission gearset overheating concern. REFER to: Transmission Cooling
. |
| P0480 |
Fan 1 Control Circuit |
REFER to: Transmission Cooling
. |
| P0481 |
Fan 2 Control Circuit |
REFER to: Transmission Cooling
. |
| P0560 |
System Voltage |
If diagnostic trouble codes (DTCs) P0562 and/or P0563 are present, RESOLVE those first. Otherwise, INSPECT the TCM power and ground circuits for opens and shorts to ground. INSPECT the TCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. If DTC P0560 returns, REFER to: Charging System
. |
| P0562 |
System Voltage Low |
GO to Pinpoint Test B |
| P0563 |
System Voltage High |
GO to Pinpoint Test C |
| P0605 |
Internal Control Module Read Only Memory (ROM) Error |
Confirm that aftermarket calibrations were not installed. PROGRAM the TCM with the latest calibration. REFER to: Module Programming
. CLEAR the TCMNVM. CARRY OUT the TCM adaptive learning procedure. REFER to: Transmission Control Module (TCM) Adaptive Learning
. If the DTC returns, INSTALL a new TCM and PROGRAM it with the latest calibration. REFER to: Transmission Control Module (TCM)
. CLEAR the TCMNVM and CARRY OUT the TCM adaptive learn procedure. REFER to: Transmission Control Module (TCM) Adaptive Learning
. |
| P0606 |
Control Module Processor |
CLEAR the DTC. If DTC P0606 returns, INSTALL a new TCM. REFER to: Transmission Control Module (TCM)
. PROGRAM the new TCM with the latest calibration. REFER to: Module Programming
. CLEAR the TCMNVM and CARRY OUT the TCM adaptive learn procedure. REFER to: Transmission Control Module (TCM) Adaptive Learning
. |
| P0607 |
Control Module Performance |
CLEAR the DTC. If DTC P0607 returns, INSTALL a new TCM. REFER to: Transmission Control Module (TCM)
. PROGRAM the new TCM with the latest calibration. REFER to: Module Programming
. CLEAR the TCMNVM and CARRY OUT the TCM adaptive learn procedure. REFER to: Transmission Control Module (TCM) Adaptive Learning
. |
| P060B |
Internal Control Module A/D Processing Performance |
If any TCM system voltage DTCs are retrieved, RESOLVE them first. Otherwise, INSTALL a new TCM. REFER to: Transmission Control Module (TCM)
. PROGRAM the new TCM with the latest calibration. REFER to: Module Programming
. CLEAR the TCMNVM and CARRY OUT the TCM adaptive learn procedure. REFER to: Transmission Control Module (TCM) Adaptive Learning
. |
| P061A |
Internal Control Module Torque Performance |
CLEAR the DTC. If DTC P061A returns, INSTALL a new TCM. REFER to: Transmission Control Module (TCM)
. PROGRAM the new TCM with the latest software. REFER to: Module Programming
. CLEAR the TCMNVM and CARRY OUT the TCM adaptive learn procedure. REFER to: Transmission Control Module (TCM) Adaptive Learning
. |
| P061B |
Internal Control Module Torque Calculation Performance |
CLEAR the DTC. If DTC P061B returns, INSTALL a new TCM. REFER to: Transmission Control Module (TCM)
. PROGRAM the new TCM with the latest calibration. REFER to: Module Programming
. CLEAR the TCMNVM and CARRY OUT the TCM adaptive learn procedure. REFER to: Transmission Control Module (TCM) Adaptive Learning
. |
| P061C |
Internal Control Module Engine RPM Performance |
CLEAR the DTC. If DTC P061C returns, INSTALL a new TCM. REFER to: Transmission Control Module (TCM)
. PROGRAM the new TCM with the latest calibration. REFER to: Module Programming
. CLEAR the TCMNVM and CARRY OUT the TCM adaptive learn procedure. REFER to: Transmission Control Module (TCM) Adaptive Learning
. |
| P062C |
Internal Control Module Vehicle Speed Performance |
CLEAR the DTC. If DTC P062C returns, INSTALL a new TCM. REFER to: Transmission Control Module (TCM)
. PROGRAM the new TCM with the latest calibration. REFER to: Module Programming
. CLEAR the TCMNVM and CARRY OUT the TCM adaptive learn procedure. REFER to: Transmission Control Module (TCM) Adaptive Learning
. |
| P062F |
Internal Control Module EEPROM Error |
CLEAR the DTC. If DTC P062F returns, INSTALL a new TCM. REFER to: Transmission Control Module (TCM)
. PROGRAM the new TCM with the latest calibration. REFER to: Module Programming
. CLEAR the TCMNVM and CARRY OUT the TCM adaptive learn procedure. REFER to: Transmission Control Module (TCM) Adaptive Learning
. |
| P0642 |
Sensor Reference Voltage "A" Circuit Low |
GO to Pinpoint Test A |
| P0643 |
Sensor Reference Voltage "A" Circuit High |
GO to Pinpoint Test A |
| P0652 |
Sensor Reference Voltage "B" Circuit Low |
GO to Pinpoint Test A |
| P0653 |
Sensor Reference Voltage "B" Circuit High |
GO to Pinpoint Test A |
| P0657 |
Actuator Supply Voltage "A" Circuit/Open |
GO to Pinpoint Test A |
| P0658 |
Actuator Supply Voltage "A" Circuit Low |
GO to Pinpoint Test A |
| P0659 |
Actuator Supply Voltage "A" Circuit High |
GO to Pinpoint Test A |
| P0667 |
Control Module Internal Temperature Sensor "A" Range/Performance |
GO to Pinpoint Test A |
| P0691 |
Fan 1 Control Circuit Low |
REFER to: Transmission Cooling
. |
| P0692 |
Fan 1 Control Circuit High |
REFER to: Transmission Cooling
. |
| P0694 |
Fan 2 Control Circuit High |
REFER to: Transmission Cooling
. |
| P0695 |
Fan 3 Control Circuit Low |
REFER to: Transmission Cooling
. |
| P0698 |
Sensor Reference Voltage "C" Circuit Low |
GO to Pinpoint Test A |
| P0699 |
Sensor Reference Voltage "C" Circuit High |
GO to Pinpoint Test A |
| P06A4 |
Sensor Reference Voltage "D" Circuit Low |
GO to Pinpoint Test A |
| P06A5 |
Sensor Reference Voltage "D" Circuit High |
GO to Pinpoint Test A |
| P06A6 |
Sensor Reference Voltage "A" Circuit Range/Performance |
GO to Pinpoint Test A |
| P06A7 |
Sensor Reference Voltage "B" Circuit Range/Performance |
GO to Pinpoint Test A |
| P06A8 |
Sensor Reference Voltage "C" Circuit Range/Performance |
GO to Pinpoint Test A |
| P06A9 |
Sensor Power Supply "A" Circuit Low |
GO to Pinpoint Test A |
| P06B1 |
Sensor Power Supply "A" Circuit Low |
GO to Pinpoint Test A |
| P06B2 |
Sensor Power Supply "A" Circuit High |
GO to Pinpoint Test A |
| P06B4 |
Sensor Power Supply "B" Circuit Low |
GO to Pinpoint Test A |
| P06B5 |
Sensor Power Supply "B" Circuit High |
GO to Pinpoint Test A |
| P06D3 |
Sensor Reference Voltage "E" Circuit Low |
GO to Pinpoint Test A |
| P06D4 |
Sensor Reference Voltage "E" Circuit High |
GO to Pinpoint Test A |
| P06D5 |
Sensor Reference Voltage "E" Circuit Range/Performance |
GO to Pinpoint Test A |
| P0710 |
Transmission Fluid Temperature Sensor "A" Circuit |
GO to Pinpoint Test A |
| P0712 |
Transmission Fluid Temperature Sensor "A" Circuit Low |
GO to Pinpoint Test A |
| P0713 |
Transmission Fluid Temperature Sensor "A" Circuit High |
GO to Pinpoint Test A |
| P0714 |
Transmission Fluid Temperature Sensor "A" Circuit Intermittent |
GO to Pinpoint Test A |
| P0715 |
TSS Sensor "A" Circuit |
GO to Pinpoint Test A |
| P0716 |
TSS Sensor "A" Circuit Range/Performance |
GO to Pinpoint Test A |
| P0720 |
Output Shaft Speed Sensor Circuit |
GO to Pinpoint Test A |
| P0721 |
Output Shaft Speed Sensor Circuit Range/Performance |
GO to Pinpoint Test A |
| P072B |
Stuck in Reverse |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P072C |
Stuck in Gear 1 |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P072D |
Stuck in Gear 2 |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P072E |
Stuck in Gear 3 |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P072F |
Stuck in Gear 4 |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P073A |
Stuck in Gear 5 |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P073B |
Stuck in Gear 6 |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P073C |
Stuck in Gear 7 |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P073E |
Unable to Engage Reverse |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P073F |
Unable to Engage Gear 1 |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P074A |
Unable to Engage Gear 2 |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P074B |
Unable to Engage Gear 3 |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P074C |
Unable to Engage Gear 4 |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P074D |
Unable to Engage Gear 5 |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P074E |
Unable to Engage Gear 6 |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P074F |
Unable to Engage Gear 7 |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P077A |
Output Shaft Speed Sensor Circuit - Loss of Direction Signal |
GO to Pinpoint Test A |
| P077C |
Output Shaft Speed Sensor Circuit Low |
GO to Pinpoint Test A |
| P077D |
Output Shaft Speed Sensor Circuit High |
GO to Pinpoint Test A |
| P077E |
Transmission Fluid Temperature Measurement System - Multiple Sensor Correlation |
GO to Pinpoint Test A |
| P0791 |
Intermediate Shaft Speed Sensor "A" Circuit |
GO to Pinpoint Test A |
| P0792 |
Intermediate Shaft Speed Sensor "A" Circuit Range/Performance |
GO to Pinpoint Test A |
| P0794 |
Intermediate Shaft Speed Sensor "A" Circuit Intermittent |
GO to Pinpoint Test A |
| P07B2 |
Transmission Park Position Sensor/Switch "A" Circuit/Open |
GO to Pinpoint Test A |
| P07B5 |
|
GO to Pinpoint Test A |
| P07BF |
TSS Sensor "A" Circuit |
GO to Pinpoint Test A |
| P07C0 |
TSS Sensor "A" Circuit High |
GO to Pinpoint Test A |
| P07C5 |
TSS Sensor "A" Circuit |
GO to Pinpoint Test A |
| P07C6 |
Intermediate Shaft Speed Sensor "A" Circuit High |
GO to Pinpoint Test A |
| P07C7 |
Intermediate Shaft Speed Sensor "B" Circuit Low |
GO to Pinpoint Test A |
| P07C8 |
Intermediate Shaft Speed Sensor "B" Circuit High |
GO to Pinpoint Test A |
| P07E4 |
Unable to Engage Park |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P07E6 |
Stuck in Park |
If any electrical diagnostic trouble codes (DTCs) are present, RESOLVE those first. If any module or communication diagnostic trouble codes (DTCs) are present, RESOLVE those second. Otherwise, INSTALL a new transmission. REFER to: Transmission - Detach from Engine
. |
| P0815 |
Upshift Switch Circuit |
REFER to: External Controls
. |
| P0816 |
Downshift Switch Circuit |
REFER to: External Controls
. |
| P0840 |
Transmission Fluid Pressure Sensor/Switch "A" Circuit |
GO to Pinpoint Test A |
| P0841 |
Transmission Fluid Pressure Sensor/Switch "A" Circuit Range/Performance |
GO to Pinpoint Test A |
| P0842 |
Transmission Fluid Pressure Sensor/Switch "A" Circuit Low |
GO to Pinpoint Test A |
| P0843 |
Transmission Fluid Pressure Sensor/Switch "A" Circuit High |
GO to Pinpoint Test A |
| P0845 |
Transmission Fluid Pressure Sensor/Switch "B" Circuit |
GO to Pinpoint Test A |
| P0846 |
Transmission Fluid Pressure Sensor/Switch "B" Circuit Range/Performance |
GO to Pinpoint Test A |
| P0847 |
Transmission Fluid Pressure Sensor/Switch "B" Circuit Low |
GO to Pinpoint Test A |
| P0848 |
Transmission Fluid Pressure Sensor/Switch "B" Circuit High |
GO to Pinpoint Test A |
| P084F |
Park / Neutral Switch Output Circuit |
GO to Pinpoint Test A |
| P0860 |
Gear Shift Control Module "A" Communication Circuit |
GO to Pinpoint Test D |
| P0861 |
Gear Shift Control Module "A" Communication Circuit Low |
GO to Pinpoint Test D |
| P0862 |
Gear Shift Control Module "A" Communication Circuit High |
GO to Pinpoint Test D |
| P0870 |
Transmission Fluid Pressure Sensor/Switch "C" Circuit |
GO to Pinpoint Test A |
| P0871 |
Transmission Fluid Pressure Sensor/Switch "C" Circuit Range/Performance |
GO to Pinpoint Test A |
| P0872 |
Transmission Fluid Pressure Sensor/Switch "C" Circuit Low |
GO to Pinpoint Test A |
| P0873 |
Transmission Fluid Pressure Sensor/Switch "C" Circuit High |
GO to Pinpoint Test A |
| P0882 |
TCM Power Input Signal Low |
GO to Pinpoint Test A |
| P0883 |
TCM Power Input Signal High |
GO to Pinpoint Test A |
| P0960 |
Pressure Control Solenoid Control Circuit/Open |
GO to Pinpoint Test A |
| P0961 |
Pressure Control Solenoid Control Circuit Range/Performance |
GO to Pinpoint Test A |
| P0962 |
Pressure Control Solenoid Control Circuit Low |
GO to Pinpoint Test A |
| P0963 |
Pressure Control Solenoid Control Circuit High |
GO to Pinpoint Test A |
| P0964 |
Pressure Control Solenoid "B" Control Circuit/Open |
GO to Pinpoint Test A |
| P0965 |
Pressure Control Solenoid "B" Control Circuit Range/Performance |
GO to Pinpoint Test A |
| P0966 |
Pressure Control Solenoid "B" Control Circuit Low |
GO to Pinpoint Test A |
| P0967 |
Pressure Control Solenoid "B" Control Circuit High |
GO to Pinpoint Test A |
| P0968 |
Pressure Control Solenoid "C" Control Circuit/Open |
GO to Pinpoint Test A |
| P0969 |
Pressure Control Solenoid "C" Control Circuit Range/Performance |
GO to Pinpoint Test A |
| P0970 |
Pressure Control Solenoid "C" Control Circuit Low |
GO to Pinpoint Test A |
| P0971 |
Pressure Control Solenoid "C" Control Circuit High |
GO to Pinpoint Test A |
| P0973 |
Shift Solenoid "A" Control Circuit Low |
GO to Pinpoint Test A |
| P0974 |
Shift Solenoid "A" Control Circuit High |
GO to Pinpoint Test A |
| P0975 |
Shift Solenoid "B" Control Circuit Range/Performance |
GO to Pinpoint Test A |
| P0976 |
Shift Solenoid "B" Control Circuit Low |
GO to Pinpoint Test A |
| P0977 |
Shift Solenoid "B" Control Circuit High |
GO to Pinpoint Test A |
| P0978 |
Shift Solenoid "C" Control Circuit Range/Performance |
GO to Pinpoint Test A |
| P0979 |
Shift Solenoid "C" Control Circuit Low |
GO to Pinpoint Test A |
| P097A |
Shift Solenoid "A" Control Circuit/Open |
GO to Pinpoint Test A |
| P097B |
Shift Solenoid "B" Control Circuit/Open |
GO to Pinpoint Test A |
| P097C |
Shift Solenoid "C" Control Circuit/Open |
GO to Pinpoint Test A |
| P097D |
Shift Solenoid "D" Control Circuit/Open |
GO to Pinpoint Test A |
| P097E |
Shift Solenoid "E" Control Circuit/Open |
GO to Pinpoint Test A |
| P097F |
Shift Solenoid "F" Control Circuit/Open |
GO to Pinpoint Test A |
| P0980 |
Shift Solenoid "C" Control Circuit High |
GO to Pinpoint Test A |
| P0981 |
Shift Solenoid "D" Control Circuit Range/Performance |
GO to Pinpoint Test A |
| P0982 |
Shift Solenoid "D" Control Circuit Low |
GO to Pinpoint Test A |
| P0983 |
Shift Solenoid "D" Control Circuit High |
GO to Pinpoint Test A |
| P0984 |
Shift Solenoid "E" Control Circuit Range/Performance |
GO to Pinpoint Test A |
| P0985 |
Shift Solenoid "E" Control Circuit Low |
GO to Pinpoint Test A |
| P0986 |
Shift Solenoid "E" Control Circuit High |
GO to Pinpoint Test A |
| P0997 |
Shift Solenoid "F" Control Circuit Range/Performance |
GO to Pinpoint Test A |
| P0998 |
Shift Solenoid "F" Control Circuit Low |
GO to Pinpoint Test A |
| P0999 |
Shift Solenoid "F" Control Circuit High |
GO to Pinpoint Test A |
| P099A |
Shift Solenoid "G" Control Circuit Range/Performance |
GO to Pinpoint Test A |
| P099B |
Shift Solenoid "G" Control Circuit Low |
GO to Pinpoint Test A |
| P099C |
Shift Solenoid "G" Control Circuit High |
GO to Pinpoint Test A |
| P09A0 |
Shift Solenoid "G" Control Circuit/Open |
GO to Pinpoint Test A |
| P2638 |
Torque Management Feedback Signal "A" Range/Performance |
GO to Pinpoint Test A |
| P2642 |
Torque Management Feedback Signal "B" Range/Performance |
GO to Pinpoint Test A |
| P2669 |
Actuator Supply Voltage "B" Circuit/Open |
GO to Pinpoint Test A |
| P2670 |
Actuator Supply Voltage "B" Circuit Low |
GO to Pinpoint Test A |
| P2671 |
Actuator Supply Voltage "B" Circuit Low |
GO to Pinpoint Test A |
| P2684 |
Actuator Supply Voltage "C" Circuit/Open |
GO to Pinpoint Test A |
| P2685 |
Actuator Supply Voltage "C" Circuit Low |
GO to Pinpoint Test A |
| P2686 |
Actuator Supply Voltage "C" Circuit High |
GO to Pinpoint Test A |
| P2718 |
Pressure Control Solenoid "D" Control Circuit/Open |
GO to Pinpoint Test A |
| P2719 |
Pressure Control Solenoid "D" Control Circuit Range/Performance |
GO to Pinpoint Test A |
| P2720 |
Pressure Control Solenoid "D" Control Circuit Low |
GO to Pinpoint Test A |
| P2721 |
Pressure Control Solenoid "D" Control Circuit High |
GO to Pinpoint Test A |
| P2727 |
Pressure Control Solenoid "E" Control Circuit/Open |
GO to Pinpoint Test A |
| P2728 |
Pressure Control Solenoid "E" Control Circuit Range/Performance |
GO to Pinpoint Test A |
| P2729 |
Pressure Control Solenoid "E" Control Circuit Low |
GO to Pinpoint Test A |
| P2730 |
Pressure Control Solenoid "E" Control Circuit High |
GO to Pinpoint Test A |
| P2736 |
Pressure Control Solenoid "F" Control Circuit/Open |
GO to Pinpoint Test A |
| P2737 |
Pressure Control Solenoid "F" Control Circuit Range/Performance |
GO to Pinpoint Test A |
| P2738 |
Pressure Control Solenoid "F" Control Circuit Low |
GO to Pinpoint Test A |
| P2739 |
Pressure Control Solenoid "F" Control Circuit High |
GO to Pinpoint Test A |
| P273F |
Transmission Fluid Temperature Sensor "B" Over Temperature Condition |
GO to Pinpoint Test A |
| P2740 |
Transmission Fluid Temperature Sensor "B" Circuit |
GO to Pinpoint Test A |
| P2742 |
Transmission Fluid Temperature Sensor "B" Circuit Low |
GO to Pinpoint Test A |
| P2743 |
Transmission Fluid Temperature Sensor "B" Circuit High |
GO to Pinpoint Test A |
| P2744 |
Transmission Fluid Temperature Sensor "B" Circuit Intermittent |
GO to Pinpoint Test A |
| P2745 |
Intermediate Shaft Speed Sensor "B" Circuit |
GO to Pinpoint Test A |
| P2746 |
Intermediate Shaft Speed Sensor "B" Circuit Range/Performance |
GO to Pinpoint Test A |
| P2748 |
Intermediate Shaft Speed Sensor "B" Circuit Intermittent |
GO to Pinpoint Test A |
| P274A |
Transmission Fluid Temperature Sensor "C" Circuit |
GO to Pinpoint Test A |
| P274B |
Transmission Fluid Temperature Sensor "C" Circuit Range/Performance |
GO to Pinpoint Test A |
| P274C |
Transmission Fluid Temperature Sensor "C" Circuit Low |
GO to Pinpoint Test A |
| P274D |
Transmission Fluid Temperature Sensor "C" Circuit High |
GO to Pinpoint Test A |
| P274E |
Transmission Fluid Temperature Sensor "C" Circuit Intermittent |
GO to Pinpoint Test A |
| P274F |
Transmission Fluid Temperature Sensor "C" Over Temperature Condition |
GO to Pinpoint Test A |
| P2777 |
Upshift Switch Circuit High |
REFER to: External Controls
. |
| P2781 |
Downshift Switch Circuit High |
REFER to: External Controls
. |
| P2787 |
Clutch 'A' Temperature Too High |
ALLOW the vehicle to cool, CHECK the clutch fluid level and correct as necessary, if the condition still exists, REFER to: Transmission Cooling
. |
| P27B2 |
Internal Control Module Transmission Range Control Performance |
GO to Pinpoint Test A |
| P27B4 |
Internal Control Module Transmission Gear Direction Control Performance |
GO to Pinpoint Test A |
| P27B5 |
Internal Control Module Transmission Gear Ratio Control Performance |
GO to Pinpoint Test A |
| P2812 |
Pressure Control Solenoid "G" Control Circuit/Open |
GO to Pinpoint Test A |
| P2813 |
Pressure Control Solenoid "G" Control Circuit Range/Performance |
GO to Pinpoint Test A |
| P2814 |
Pressure Control Solenoid "G" Control Circuit Low |
GO to Pinpoint Test A |
| P2815 |
Pressure Control Solenoid "G" Control Circuit High |
GO to Pinpoint Test A |
| P281B |
Pressure Control Solenoid "H" Control Circuit/Open |
GO to Pinpoint Test A |
| P281C |
Pressure Control Solenoid "H" Control Circuit Range/Performance |
GO to Pinpoint Test A |
| P281D |
Pressure Control Solenoid "H" Control Circuit Low |
GO to Pinpoint Test A |
| P281E |
Pressure Control Solenoid "H" Control Circuit High |
GO to Pinpoint Test A |
| P2824 |
Pressure Control Solenoid "J" Control Circuit/Open |
GO to Pinpoint Test A |
| P2825 |
Pressure Control Solenoid "J" Control Circuit Range/Performance |
GO to Pinpoint Test A |
| P2826 |
Pressure Control Solenoid "J" Control Circuit Low |
GO to Pinpoint Test A |
| P2827 |
Pressure Control Solenoid "J" Control Circuit High |
GO to Pinpoint Test A |
| P2831 |
Shift Fork "A" Position Circuit |
GO to Pinpoint Test A |
| P2832 |
Shift Fork "A" Position Circuit Range/Performance |
GO to Pinpoint Test A |
| P2836 |
Shift Fork "B" Position Circuit |
GO to Pinpoint Test A |
| P2837 |
Shift Fork "B" Position Circuit Range/Performance |
GO to Pinpoint Test A |
| P283B |
Shift Fork "C" Position Circuit |
GO to Pinpoint Test A |
| P283C |
Shift Fork "C" Position Circuit Range/Performance |
GO to Pinpoint Test A |
| P2840 |
Shift Fork "D" Position Circuit |
GO to Pinpoint Test A |
| P2841 |
Shift Fork "D" Position Circuit Range/Performance |
GO to Pinpoint Test A |
| P284D |
Shift Fork "A" Unrequested Movement |
GO to Pinpoint Test A |
| P284E |
Shift Fork "B" Unrequested Movement |
GO to Pinpoint Test A |
| P284F |
Shift Fork "C" Unrequested Movement |
GO to Pinpoint Test A |
| P2850 |
Shift Fork "D" Unrequested Movement |
GO to Pinpoint Test A |
| P2863 |
Shift Fork "E" Position Circuit |
GO to Pinpoint Test A |
| P2864 |
Shift Fork "E" Position Circuit Range/Performance |
GO to Pinpoint Test A |
| P2865 |
Shift Fork "E" Position Circuit Low |
GO to Pinpoint Test A |
| P2866 |
Shift Fork "E" Position Circuit High |
GO to Pinpoint Test A |
| P287C |
Transmission Adaptive Values Not Learned |
CLEAR the DTC. CARRY OUT the adaptive learning procedure. REFER to: Transmission Control Module (TCM) Adaptive Learning
. If the DTC returns, INSTALL a new TCM. REFER to: Transmission Control Module (TCM)
. PROGRAM the new TCM with the latest calibration. REFER to: Module Programming
. CLEAR the TCMNVM and CARRY OUT the TCM adaptive learn procedure. REFER to: Transmission Control Module (TCM) Adaptive Learning
. |
| U0073 |
Control Module Communication Bus "A" Off |
GO to Pinpoint Test A |
| U0074 |
Control Module Communication Bus "B" Off |
GO to Pinpoint Test A |
| U0100 |
Lost Communication With ECM/PCM "A" |
GO to Pinpoint Test E |
| U0103 |
Lost Communication With Gear Shift Control Module A |
GO to Pinpoint Test F |
| U0121 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module |
GO to Pinpoint Test G |
| U0140 |
Lost Communication With Body Control Module |
GO to Pinpoint Test H |
| U0155 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module |
GO to Pinpoint Test I |
| U0400 |
Invalid Data Received |
This DTC sets when the TCM receives invalid network data from another module. RETRIEVE and RESOLVE all non-network diagnostic trouble codes (DTCs) in other modules on the network first. RESOLVE all network related diagnostic trouble codes (DTCs) in other modules on the network second. CLEAR the DTC. If DTC U0400 returns, INSTALL a new TCM. REFER to: Transmission Control Module (TCM)
. PROGRAM the new TCM with the latest calibration. REFER to: Module Programming
. CLEAR the TCMNVM and CARRY OUT the TCM adaptive learn procedure. REFER to: Transmission Control Module (TCM) Adaptive Learning
. |
| U0401 |
Invalid Data Received from ECM/PCM A |
GO to Pinpoint Test E |
| U0404 |
Invalid Data Received from Gear Shift Control Module A |
GO to Pinpoint Test F |
| U0415 |
Invalid Data Received From Anti-Lock Brake System (ABS) Control Module |
GO to Pinpoint Test G |
| U0422 |
Invalid Data Received From Body Control Module |
GO to Pinpoint Test H |
| U0423 |
Invalid Data Received from Instrument Panel Cluster Control Module |
GO to Pinpoint Test I |
| U1012 |
Invalid Internal Control Module Monitoring Data Received from Anti-Lock Brake System (ABS) Control Module |
GO to Pinpoint Test G |
| U101E |
Invalid Internal Control Module Monitoring Data Received from Gear Shift Module |
GO to Pinpoint Test F |