Anti-Lock Brake System And Stability Control DTCS: SASM
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| C1B00:49 | Steering Angle Sensor: Internal Electrical Failure | CHECK vehicle service history for recent service actions related to the SASM. This DTC sets due to incomplete or improper flash programming procedures. If there have been recent service actions with the SASM, REPEAT the programming procedure as directed by the diagnostic scan tool. If there have been no recent service actions, CLEAR the DTC, CYCLE the ignition, CARRY OUT the SASM self-test. If the DTC returns, INSTALL a new SASM to correct the failure to retain software data. REFER to: Steering Angle Sensor Module (SASM) . |
| C1B00:61 | Steering Angle Sensor: Signal Calculation Failure | This DTC indicates that part of the SASM has failed internally. CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If the DTC returns, INSTALL a new SASM. REFER to: Steering Angle Sensor Module (SASM) . |
| C1B00:62 | Steering Angle Sensor: Signal Compare Failure | This DTC indicates that part of the SASM has failed internally. CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If the DTC returns, INSTALL a new SASM. REFER to: Steering Angle Sensor Module (SASM) . |
| C1B00:64 | Steering Angle Sensor: Signal Plausibility Failure | CLEAR the DTC. TEST DRIVE the vehicle and CARRY OUT at least 1 left turn and 1 right turn. CARRY OUT a SASM self-test. If the DTC returns, INSTALL a new SASM. REFER to: Steering Angle Sensor Module (SASM) . |
| C1B00:81 | Steering Angle Sensor: Invalid Serial Data Received | This DTC indicates that part of the SASM has failed internally. CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If the DTC returns, INSTALL a new SASM. REFER to: Steering Angle Sensor Module (SASM) . |
| C1B00:85 | Steering Angle Sensor: Signal Above Allowable Range | SET the front wheels to the straight ahead position. Using a diagnostic scan tool, OBSERVE the SASM steering wheel angle (SW_ANGLE) PID. If the PID displays 0 degrees, CLEAR the DTC, REPEAT the SASM self-test. If the DTC returns, INSTALL a new SASM. If the PID displays more than 360 degrees, SET the ignition to OFF. REMOVE the SASM REFER to: Steering Angle Sensor Module (SASM) .Leave the electrical connector connected . SET the ignition to ON (this causes Diagnostic Trouble Codes (DTCs) to set in multiple modules). Manually ADJUST the SASM until the SW_ANGLE PID displays 0 degrees. SET the ignition to OFF. INSTALL the SASM. CLEAR all Continuous Memory Diagnostic Trouble Codes (CMDTCs) in all modules. |
| C1B00:87 | Steering Angle Sensor: Missing Message | The module could not communicate on the network at a point in time. The fault is not currently present since the module is able to communicate with the diagnostic scan tool to report this DTC. VERIFY the integrity of the connectors and wiring. Refer to Module Communications Network for schematic and connector information. |
| C1B00:92 | Steering Angle Sensor: Performance or Incorrect Operation | CLEAR the DTC. TEST DRIVE the vehicle and CARRY OUT at least 1 left turn and 1 right turn. CARRY OUT a SASM self-test. If the DTC returns, INSTALL a new SASM. REFER to: Steering Angle Sensor Module (SASM) . |
| C1B00:96 | Steering Angle Sensor: Component Internal Failure | This DTC indicates that part of the SASM has failed internally. CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If the DTC returns, INSTALL a new SASM. REFER to: Steering Angle Sensor Module (SASM) . |
| U0001:88 | High Speed CAN Communication Bus: Bus Off | The module could not communicate on the network at a point in time. The fault is not currently present since the module is able to communicate with the diagnostic scan tool to report this DTC. VERIFY the integrity of the connectors and wiring. Refer to Module Communications Network for schematic and connector information. |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test D |
| U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | GO to Pinpoint Test P |
| U3003:62 | Battery Voltage: Signal Compare Failure | GO to Pinpoint Test K |