Pinpoint Test L OCS Faults Reported By RCM

L1 : RETRIEVE RCM DTCS

WARNING: Before beginning any service procedure in this service information, refer to Safety Warnings in appropriate GENERAL INFORMATION article. Failure to follow this instruction may result in serious personal injury.

NOTE: Diagnose all network-related (lost communication) DTCs first.

Ignition ON, engine OFF.
Carry out the RCM self-test.
Is DTC B00A0:09, B00A0:4A, B00A0:63, B00A0:64 or B00A0:68 retrieved as an on-demand (not continuous) DTC during the self-test?

Yes	No
This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test. For DTC B00A0:09, B00A0:63 or B00A0:68, RETRIEVE and DIAGNOSE the OCSM DTCs. Disregard the current DTC at this time. GO to DTC/SYMPTOM CHART to address the next DTC. For DTC B00A0:4A or B00A0:64, Go to L2. For all others, No fault found.	CHECK for causes of the intermittent fault. REFER to appropriate Supplemental Restraint System in OEM Wiring Diagrams article, for schematic and connector information. ATTEMPT to recreate the hard fault by flexing the wire harness and cycling the ignition frequently. DO NOT install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. Go to L6.

Yes

This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test.
For DTC B00A0:09, B00A0:63 or B00A0:68, RETRIEVE and DIAGNOSE the OCSM DTCs. Disregard the current DTC at this time. GO to DTC/SYMPTOM CHART to address the next DTC.
For DTC B00A0:4A or B00A0:64, Go to L2.
For all others, No fault found.

CHECK for causes of the intermittent fault. REFER to appropriate Supplemental Restraint System in OEM Wiring Diagrams article, for schematic and connector information. ATTEMPT to recreate the hard fault by flexing the wire harness and cycling the ignition frequently. DO NOT install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test.
Go to L6.

L2 : VERIFY THE OCSM PART NUMBER

NOTE: It is necessary to exit the guided diagnostics to use the IDS to use the Log Viewer function.

Using the Log Viewer function of the diagnostic scan tool, retrieve and record the OCSM part number.
Check the part number recorded against the number listed in the parts catalog and verify the correct OCSM is present in the vehicle.
Is the correct OCSM installed?

Yes	No
Go to L4.	INSTALL the correct RCM. Go to L5.

L3 : VERIFY THE RCM PART NUMBER

NOTE: It is necessary to exit the guided diagnostics to use the IDS to use the Log Viewer function.

Using the Log Viewer function of the diagnostic scan tool, retrieve and record the RCM part number.
Check the part number recorded against the number listed in the parts catalog and verify the correct RCM is present in the vehicle.
Is the correct RCM installed?

Yes	No
Go to L4.	INSTALL the correct RCM. Go to L5.

L4 : VERIFY THE RCM CONFIGURATION

NOTE: It is necessary to exit the guided diagnostics to use the IDS to carry out the PMI process.

Carry out PMI for the RCM. Manually enter As-Built data. Refer to the diagnostic scan tool instructions when carrying out PMI.
Carry out the RCM self-test.
Is DTC B00A0:4A retrieved on-demand during self-test?

Yes	No
Go to L5.	The fault is corrected. Go to L6.

L5 : REPLACE THE RCM
- Ignition OFF.
- CHECK OASIS for any applicable TSBs.
  - If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions.
  - f no TSBs address this concern, INSTALL a new RCM. Refer to appropriate SUPPLEMENTAL RESTRAINT SYSTEM article
INSTALL a new RCM.

Reconnect all previously disconnected SRS components and repower the SRS. Refer to appropriate SUPPLEMENTAL RESTRAINT SYSTEM article.

Carry out the OCSM and RCM self-test and record DTCs if present. Do not clear any DTCs until all DTCs have been resolved. DIAGNOSE and REPAIR the RCM and/or OCSM DTCs.

Carry out the OCSM and RCM self-test and record DTCs if present. Do not clear any DTCs until all DTCs have been resolved.

If any SRS DTCs are retrieved, DO NOT clear any DTCs until all DTCs have been resolved. DIAGNOSE and REPAIR the RCM and/or OCSM DTCs.

If no DTCs are retrieved on-demand, the repair is complete. RETURN the vehicle to the customer.

L6 : CHECK FOR ADDITIONAL SRS DIAGNOSTIC TROUBLE CODES (DTCS)

Clear the RCM DTCs.
Ignition OFF.
Ignition ON, engine OFF.
NOTE: When selecting Restraints from the Self Test menu, DTCs are retrieved from the RCM, OCSM and, if equipped, BECM-B.
Wait 10 seconds.
Carry out the RCM self-test.
Carry out the OCS self-test.
Are any RCM, OCSM and/or BECM-B DTCs retrieved on-demand during self-test?

Yes	No
Do not clear any DTCs until all DTCs have been resolved. REFER to the RCM or OCSM DTC Chart.	The repair is complete. RETURN the vehicle to the customer.