Common Specifications & Procedures
EDGE COMMON SPECIFICATIONS & PROCEDURES
| System | Specifications/Procedures | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | Specifications | |||
| Torque | Refer to the appropriate component in Removal And Installation . | |||
| Axle Nut/Hub Nut | ||||
| Front | 148 lb.ft (200 Nm) | |||
| Rear | ||||
| AWD | 148 lb.ft (200 Nm) | |||
| FWD | 148 lb.ft (200 Nm) | |||
| Battery | Specifications | |||
| Brakes | ||||
| Bleeding Sequence | Brake System Pressure Bleeding | |||
| Front Disc Brakes w/Torque | Refer to appropriate component in Removal And Installation | |||
| Rear Disc Brakes w/Torque | Refer to appropriate component in Removal And Installation | |||
| Charging | ||||
| Generator w/Torque | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | Upper Generator Bolt: 18 lb.ft (25 Nm) Lower Generator Bolts: 18 lb.ft (25 Nm) |
|||
| 2.7L EcoBoost (238kW/324PS) | Generator Bolt and Stud Nut: 35 lb.ft (47 Nm) | |||
| 3.5L Duratec (212kW/278PS) | Generator Stud Nut: 35 lb.ft (47 Nm) Generator Stud Bolt: 71 lb.in (8 Nm) Generator and Bolt: 35 lb.ft (47 Nm) |
|||
| Drive Belts | ||||
| Adjustment | ||||
| 2.0L ECOBOOST (184KW/250PS) - MI4 | Accessory Drive | |||
| 2.7L EcoBoost (238kW/324PS) | Accessory Drive | |||
| Belt Routing | ||||
| 2.0L ECOBOOST (184KW/250PS) - MI4 | Accessory Drive - Component Location | |||
| 2.7L EcoBoost (238kW/324PS) | Accessory Drive - Component Location | |||
| Engine Cooling | ||||
| General Service Specifications | ||||
| 2.0L ECOBOOST (184KW/250PS) - MI4 | Specifications | |||
| 2.7L EcoBoost (238kW/324PS) | Specifications | |||
| Radiator Cap Pressure | 145 kPa (21 psi) |
|||
| Radiator Pressure Test (Removed From The Vehicle) | 138 kPa (20 psi) | |||
| Thermostat R & I | ||||
| 2.0L GDTI | Thermostat Housing | |||
| 2.7L | Thermostat | |||
| Water Pump R & I | ||||
| 2.0L GDTI | Coolant Pump | |||
| 2.7L | Coolant Pump | |||
| Engine Mechanical | ||||
| 2.0L GDTI | ||||
| Compression | Specifications | |||
| Oil Pressure (Hot @ 2000 RPM) | 29-60 psi (200-414 kPa) | |||
| Overhaul | Specifications | |||
| Torque | Removal And Installation | |||
| 2.7L | ||||
| Compression | Specifications | |||
| Oil Pressure Reading 1 (Minimum average oil pressure @ 2, 000 rpm after 15 secs with engine at normal operating temperature and transmission in Park.) | 21 psi (144.8 kPa) | |||
| Oil Pressure Reading 2 (Minimum average oil pressure @ 2, 000 rpm after 15 secs with engine at normal operating temperature and transmission in Park (Oil Pressure Control Solenoid connector disconnected)) | Reading 1 value plus 8 psi (55.1 kPa) | |||
| Overhaul | Specifications | |||
| Torque | Refer to appropriate component in Removal And Installation (1 Of 2) , or Removal And Installation (2 Of 2) | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |||
| Flywheel/Flex Plate Torque | ||||
| 2.0L GDTI | For tightening sequence, refer to Flexplate
. Stage 1: 50 Nm (37 lb-ft). Stage 2: 80 Nm (59 lb-ft). Stage 3: 112 Nm (83 lb-ft). |
|||
| 2.7L | 59 lb.ft (80 Nm) | |||
| Fuel System | ||||
| Fuel Filter Location | Located in fuel tank as part of Fuel Pump Module. | |||
| Fuel Filter R & I | ||||
| 2.0L GDTI | Fuel Pump And Sender Unit | |||
| 2.7L | Fuel Pump And Sender Unit | |||
| Pressure Release Procedure | ||||
| 2.0L GDTI | Fuel System Pressure Release | |||
| 2.7L | Fuel System Pressure Release | |||
| Pressure Specification | ||||
| 2.0L GDTI | General Procedures | |||
| 2.7L | General Procedures | |||
| Fuel Pressure Test Procedure | ||||
| 2.0L GDTI | Fuel System Pressure Check | |||
| 2.7L | Fuel System Pressure Check | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | Firing Order & Cylinder Identification | |||
| Ignition Wires (Routing) | Engines are equipped with Coil-on-plug ignition. | |||
| Spark Plugs | ||||
| 2.0L GTDI | ||||
| Type | CYFS 12Y PCT | |||
| Gap | 0.030 In. (0.75 mm) | |||
| Torque | 106 In. Lbs. (12 N.m) | |||
| 2.7L | ||||
| Type | CYFS 12Y PT | |||
| Gap | 0.028-0.031 in (0.7-0.8 mm) | |||
| Torque | 133 In. Lbs. (15 N.m) | |||
| Starting | ||||
| Starter | ||||
| 2.0L | Specifications | |||
| 2.7L | Specifications | |||
| Torque | ||||
| 2.0L | For removal and installation, refer to Starter Motor . | |||
| 2.7L | For removal and installation, refer to Starter Motor . | |||
| Wheel Alignment | ||||
| Adjustment Specifications | Specifications | |||
| Torque | Refer to the appropriate procedure in General Procedures | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | For tightening sequence, refer to Wheel and Tire 162 lb.ft (220 Nm) |
|||