| B10DA:51 |
PATS Target Identifier: Not Programmed |
GO to Pinpoint Test P |
| C0001:01 |
TCS Control Channel "A" Valve 1: General Electrical Failure |
GO to Pinpoint Test Y |
| C0002:01 |
TCS Control Channel "A" Valve 2: General Electrical Failure |
GO to Pinpoint Test Y |
| C0003:01 |
TCS Control Channel "B" Valve 1: General Electrical Failure |
GO to Pinpoint Test Y |
| C0004:01 |
TCS Control Channel "B" Valve 2: General Electrical Failure |
GO to Pinpoint Test Y |
| C0020:11 |
ABS Pump Motor Control: Circuit Short To Ground |
GO to Pinpoint Test H |
| C0020:12 |
ABS Pump Motor Control: Circuit Short To Battery |
GO to Pinpoint Test H |
| C0020:13 |
ABS Pump Motor Control: Circuit Open |
GO to Pinpoint Test H |
| C0020:49 |
ABS Pump Motor Control: Internal Electronic Failure |
GO to Pinpoint Test H |
| C0020:71 |
ABS Pump Motor Control: Actuator Stuck |
GO to Pinpoint Test H |
| C0030:07 |
Left Front Tone Wheel: Mechanical Failures |
GO to Pinpoint Test AB |
| C0031:01 |
Left Front Wheel Speed Sensor: General Electrical Failure |
GO to Pinpoint Test M |
| C0031:07 |
Left Front Wheel Speed Sensor: Mechanical Failures |
GO to Pinpoint Test AB |
| C0031:2F |
Left Front Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test AB |
| C0031:4A |
Left Front Wheel Speed Sensor: Incorrect Component Installed |
GO to Pinpoint Test AL |
| C0031:64 |
Left Front Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| C0033:07 |
Right Front Tone Wheel: Mechanical Failures |
GO to Pinpoint Test AB |
| C0034:01 |
Right Front Wheel Speed Sensor: General Electrical Failure |
GO to Pinpoint Test M |
| C0034:07 |
Right Front Wheel Speed Sensor: Mechanical Failures |
GO to Pinpoint Test AB |
| C0034:2F |
Right Front Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test AB |
| C0034:4A |
Right Front Wheel Speed Sensor: Incorrect Component Installed |
GO to Pinpoint Test AL |
| C0034:64 |
Right Front Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| C0036:07 |
Left Rear Tone Wheel: Mechanical Failures |
GO to Pinpoint Test AB |
| C0037:01 |
Left Rear Wheel Speed Sensor: General Electrical Failure |
GO to Pinpoint Test N |
| C0037:07 |
Left Rear Wheel Speed Sensor: Mechanical Failures |
GO to Pinpoint Test AB |
| C0037:2F |
Left Rear Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test AB |
| C0037:4A |
Left Rear Wheel Speed Sensor: Incorrect Component Installed |
GO to Pinpoint Test AL |
| C0037:64 |
Left Rear Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| C0039:07 |
Right Rear Tone Wheel: Mechanical Failures |
GO to Pinpoint Test AB |
| C003A:01 |
Right Rear Wheel Speed Sensor: General Electrical Failure |
GO to Pinpoint Test N |
| C003A:07 |
Right Rear Wheel Speed Sensor: Mechanical Failures |
GO to Pinpoint Test AB |
| C003A:2F |
Right Rear Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test AB |
| C003A:4A |
Right Rear Wheel Speed Sensor: Incorrect Component Installed |
GO to Pinpoint Test AL |
| C003A:64 |
Right Rear Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| C0040:64 |
Brake Pedal Switch "A": Signal Plausibility Failure |
GO to Pinpoint Test AC |
| C0044:49 |
Brake Pressure Sensor "A": Internal Electronic Failure |
GO to Pinpoint Test AM |
| C0044:51 |
Brake Pressure Sensor "A": Not Programmed |
GO to Pinpoint Test AM |
| C0044:64 |
Brake Pressure Sensor "A": Signal Plausibility Failure |
GO to Pinpoint Test AM |
| C0044:8F |
Brake Pressure Sensor "A": Erratic |
GO to Pinpoint Test AM |
| C0047:1C |
Brake Booster Pressure Sensor: Circuit Voltage Out Of Range |
GO to Pinpoint Test C |
| C0047:1C |
Brake Booster Pressure Sensor: Circuit Voltage Out Of Range |
GO to Pinpoint Test CO |
| C0047:26 |
Brake Booster Pressure Sensor: Signal Rate Of Change Below Threshold |
GO to Pinpoint Test C |
| C0047:27 |
Brake Booster Pressure Sensor: Signal Rate Of Change Above Threshold |
GO to Pinpoint Test C |
| C0047:31 |
Brake Booster Pressure Sensor: No Signal |
GO to Pinpoint Test C |
| C0047:64 |
Brake Booster Pressure Sensor: Signal Plausibility Failure |
GO to Pinpoint Test CO |
| C0049:01 |
Brake Fluid Level: General Electrical Failure |
GO to Pinpoint Test L |
| C0049:7A |
Brake Fluid Level: Fluid Leak Or Seal Failure |
GO to Pinpoint Test L |
| C0049:7B |
Brake Fluid Level: Low Fluid Level |
GO to Pinpoint Test L |
| C0051:64 |
Steering Wheel Position Sensor: Signal Plausibility Failure |
GO to Pinpoint Test LA |
| C0051:67 |
Steering Wheel Position Sensor: Signal Incorrect After Event |
GO to Pinpoint Test LA |
| C0051:85 |
Steering Wheel Position Sensor: Signal Above Allowable Range |
GO to Pinpoint Test LA |
| C0051:86 |
Steering Wheel Position Sensor: Signal Invalid |
GO to Pinpoint Test LA |
| C0061:28 |
Lateral Acceleration Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test BH |
| C0061:54 |
Lateral Acceleration Sensor: Missing Calibration |
GO to Pinpoint Test AN |
| C0061:64 |
Lateral Acceleration Sensor: Signal Plausibility Failure |
GO to Pinpoint Test BH |
| C0062:28 |
Longitudinal Acceleration Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test BH |
| C0062:54 |
Longitudinal Acceleration Sensor: Missing Calibration |
GO to Pinpoint Test AN |
| C0062:64 |
Longitudinal Acceleration Sensor: Signal Plausibility Failure |
GO to Pinpoint Test BH |
| C0063:28 |
Yaw Rate Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test BH |
| C0063:64 |
Yaw Rate Sensor: Signal Plausibility Failure |
GO to Pinpoint Test BH |
| C0064:28 |
Roll Rate Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test BH |
| C0064:64 |
Roll Rate Sensor: Signal Plausibility Failure |
GO to Pinpoint Test BH |
| C006A:95 |
Multi-axis Acceleration Sensor: Incorrect Assembly |
GO to Pinpoint Test AN |
| C006B:00 |
Stability System Active Too Long: No Sub Type Information |
GO to Pinpoint Test AD |
| C0078:56 |
Tire Diameter: Invalid/Incompatible Configuration |
GO to Pinpoint Test ZA |
| C052E:A2 |
ABS Pump Motor Control Circuit Low: System Voltage Low |
GO to Pinpoint Test H |
| C0564:00 |
ABS Control Module System Voltage Low: No Sub Type Information |
GO to Pinpoint Test A |
| C0594:12 |
Brake Booster Motor "A" Performance: Circuit Short To Battery |
GO to Pinpoint Test CP |
| C0594:78 |
Brake Booster Motor "A" Performance: Alignment Or Adjustment Incorrect |
GO to Pinpoint Test CP |
| C0594:92 |
Brake Booster Motor "A" Performance: Performance Or Incorrect Operation |
GO to Pinpoint Test CP |
| C0596:00 |
Brake Booster Motor "A" Current Sensor Circuit Range/Performance: No Sub Type Information |
GO to Pinpoint Test CP |
| C1013:09 |
Brake System Pressure: Component Failures |
GO to Pinpoint Test CO |
| C1013:7A |
Brake System Pressure: Fluid Leak Or Seal Failure |
GO to Pinpoint Test CO |
| C1013:7C |
Brake System Pressure: Slow Response |
GO to Pinpoint Test CO |
| C1013:92 |
Brake System Pressure: Performance Or Incorrect Operation |
GO to Pinpoint Test CO |
| C1015:7A |
Vacuum Supply: Fluid Leak Or Seal Failure |
GO to Pinpoint Test AH |
| C1015:7B |
Vacuum Supply: Low Fluid Level |
GO to Pinpoint Test AH |
| C1018:61 |
Regenerative Braking: Signal Calculation Failure |
GO to Pinpoint Test Z |
| C1019:29 |
Linear Actuator Control (LAC): Signal Invalid |
GO to Pinpoint Test CO |
| C1019:74 |
Linear Actuator Control (LAC): Actuator Slipping |
GO to Pinpoint Test CO |
| C1019:78 |
Linear Actuator Control (LAC): Alignment Or Adjustment Incorrect |
GO to Pinpoint Test CO |
| C1019:92 |
Linear Actuator Control (LAC): Performance Or Incorrect Operation |
GO to Pinpoint Test CO |
| C101F:46 |
Generic Valve Failure: Calibration/Parameter Memory Failure |
GO to Pinpoint Test Z |
| C101F:49 |
Generic Valve Failure: Internal Electronic Failure |
GO to Pinpoint Test Z |
| C1020:00 |
Brake System Fill Not Complete: No Sub Type Information |
GO to Pinpoint Test T |
| C1020:52 |
Brake System Fill Not Complete: Not Activated |
GO to Pinpoint Test T |
| C1109:64 |
Vehicle Dynamics Control Switch: Signal Plausibility Failure |
GO to Pinpoint Test O |
| C1137:64 |
Reverse gear switch: Signal Plausibility Failure |
GO to Pinpoint Test AI |
| C1A08:1C |
Pressure Sensor Supply: Circuit Voltage Out Of Range |
GO to Pinpoint Test AM |
| C1B11:71 |
Pressure Control Valve: Actuator Stuck |
GO to Pinpoint Test Y |
| P05D3:86 |
Driver Mode Select Switch "A" Range/Performance: Signal Invalid |
GO to Pinpoint Test AA |
| U0100:00 |
Lost Communication With ECM/PCM "A": No Sub Type Information |
GO to Pinpoint Test AI |
| U0101:00 |
Lost Communication with TCM: No Sub Type Information |
GO to Pinpoint Test AI |
| U0103:00 |
Lost Communication With Gear Shift Control Module A: No Sub Type Information |
GO to Pinpoint Test AV |
| U011D:00 |
Lost Communication With All Wheel Drive Control Module: No Sub Type Information |
GO to Pinpoint Test BX |
| U0131:00 |
Lost Communication With Power Steering Control Module "A": No Sub Type Information |
GO to Pinpoint Test AE |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test D |
| U0146:00 |
Lost Communication With Serial Data Gateway "A": No Sub Type Information |
GO to Pinpoint Test BP |
| U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test BH |
| U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test AR |
| U0164:00 |
Lost Communication With HVAC Control Module: No Sub Type Information |
GO to Pinpoint Test CE |
| U023A:00 |
Lost Communication With Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test BQ |
| U0256:00 |
Lost Communication With Front Controls Interface Module "A": No Sub Type Information |
GO to Pinpoint Test AS |
| U0300:51 |
Internal Control Module Software Incompatibility: Not Programmed |
GO to Pinpoint Test Z |
| U0401:00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
GO to Pinpoint Test AI |
| U0401:64 |
Invalid Data Received from ECM/PCM A: Signal Plausibility Failure |
GO to Pinpoint Test AI |
| U0401:86 |
Invalid Data Received from ECM/PCM A: Signal Invalid |
GO to Pinpoint Test AI |
| U0402:00 |
Invalid Data Received from TCM: No Sub Type Information |
GO to Pinpoint Test AI |
| U0404:00 |
Invalid Data Received from Gear Shift Control Module A: No Sub Type Information |
GO to Pinpoint Test AV |
| U041E:00 |
Invalid Data Received From All Wheel Drive Control Module: No Sub Type Information |
GO to Pinpoint Test BX |
| U0420:00 |
Invalid Data Received from Power Steering Control Module "A": No Sub Type Information |
GO to Pinpoint Test AE |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test D |
| U0424:00 |
Invalid Data Received From HVAC Control Module: No Sub Type Information |
GO to Pinpoint Test CE |
| U0424:86 |
Invalid Data Received From HVAC Control Module: Signal Invalid |
GO to Pinpoint Test CE |
| U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test BH |
| U0452:86 |
Invalid Data Received From Restraints Control Module: Signal Invalid |
GO to Pinpoint Test BH |
| U053B:00 |
Invalid Data Received From Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test BQ |
| U0557:00 |
Invalid Data Received From Front Controls Interface Module "A": No Sub Type Information |
GO to Pinpoint Test AS |
| U0594:00 |
Invalid Data Received From Hybrid/EV Powertrain Control Module "A": No Sub Type Information |
GO to Pinpoint Test CM |
| U2001:00 |
Reduced System Function: No Sub Type Information |
GO to Pinpoint Test G |
| U2017:57 |
Control Module Software #2: Invalid/Incompatible Software Component |
GO to Pinpoint Test Z |
| U2017:93 |
Control Module Software #2: No Operation |
GO to Pinpoint Test Z |
| U2018:57 |
Control Module Software #3: Invalid/Incompatible Software Component |
GO to Pinpoint Test Z |
| U2024:51 |
Control Module Cal-Config Data: Not Programmed |
GO to Pinpoint Test Z |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test Z |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test Z |
| U2107:00 |
Collision Mitigation By Braking: No Sub Type Information |
GO to Pinpoint Test R |
| U2107:68 |
Collision Mitigation By Braking: Event Information |
GO to Pinpoint Test AQ |
| U2108:68 |
Adaptive Cruise Control: Event Information |
GO to Pinpoint Test AQ |
| U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test Z |
| U3000:00 |
Control Module: No Sub Type Information |
GO to Pinpoint Test Y |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test Y |
| U3000:4B |
Control Module: Over Temperature |
GO to Pinpoint Test Y |
| U3000:96 |
Control Module: Component Internal Failure |
GO to Pinpoint Test Y |
| U3002:51 |
Vehicle Identification Number: Not Programmed |
GO to Pinpoint Test AF |
| U3002:62 |
Vehicle Identification Number: Signal Compare Failure |
GO to Pinpoint Test AF |
| U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test A |
| U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test F |
| U300A:29 |
Ignition Switch: Signal Invalid |
GO to Pinpoint Test A |
| U3012:68 |
Control Module Improper Wake-up Performance: Event Information |
GO to Pinpoint Test X |