| B10DA:51 |
PATS Target Identifier: Not Programmed |
GO to Pinpoint Test P |
| C0030:07 |
Left Front Tone Wheel: Mechanical Failure |
GO to Pinpoint Test AB |
| C0031:01 |
Left Front Wheel Speed Sensor: General Circuit/Electrical Failure |
GO to Pinpoint Test M |
| C0031:2F |
Left Front Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test AB |
| C0031:64 |
Left Front Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| C0033:07 |
Right Front Tone Wheel: Mechanical Failure |
GO to Pinpoint Test AB |
| C0034:01 |
Right Front Wheel Speed Sensor: General Circuit/Electrical Failure |
GO to Pinpoint Test M |
| C0034:2F |
Right Front Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test AB |
| C0034:64 |
Right Front Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| C0036:07 |
Left Rear Tone Wheel: Mechanical Failure |
GO to Pinpoint Test AB |
| C0037:01 |
Left Rear Wheel Speed Sensor: General Circuit/Electrical Failure |
GO to Pinpoint Test N |
| C0037:2F |
Left Rear Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test AB |
| C0037:64 |
Left Rear Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| C0039:07 |
Right Rear Tone Wheel: Mechanical Failure |
GO to Pinpoint Test AB |
| C003A:01 |
Right Rear Wheel Speed Sensor: General Circuit/Electrical Failure |
GO to Pinpoint Test N |
| C003A:2F |
Right Rear Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test AB |
| C003A:64 |
Right Rear Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| C0040:01 |
Brake Pedal Switch 'A': General Circuit/Electrical Failure |
GO to Pinpoint Test CW |
| C0040:04 |
Brake Pedal Switch 'A': System Internal Failure |
GO to Pinpoint Test CW |
| C0040:64 |
Brake Pedal Switch 'A': Signal Plausibility Failure |
GO to Pinpoint Test CW |
| C0041:01 |
Brake Pedal Switch 'B': General Circuit/Electrical Failure |
GO to Pinpoint Test CW |
| C0041:14 |
Brake Pedal Switch 'B': Circuit Short To Ground Or Open |
GO to Pinpoint Test CW |
| C0041:4B |
Brake Pedal Switch 'B': Over Temperature |
GO to Pinpoint Test CW |
| C0044:49 |
Brake Pressure Sensor 'A': Internal Electronic Failure |
GO to Pinpoint Test AM |
| C0044:64 |
Brake Pressure Sensor 'A': Signal Plausibility Failure |
GO to Pinpoint Test AM |
| C0044:8F |
Brake Pressure Sensor 'A': Erratic |
GO to Pinpoint Test AM |
| C0047:01 |
Brake Booster Pressure Sensor: General Circuit/Electrical Failure |
GO to Pinpoint Test CO |
| C0047:1C |
Brake Booster Pressure Sensor: Circuit Voltage Out Of Range |
GO to Pinpoint Test CO |
| C0047:31 |
Brake Booster Pressure Sensor: No Signal |
GO to Pinpoint Test CO |
| C0047:64 |
Brake Booster Pressure Sensor: Signal Plausibility Failure |
GO to Pinpoint Test CO |
| C0049:01 |
Brake Fluid Level: General Circuit/Electrical Failure |
GO to Pinpoint Test L |
| C0049:7B |
Brake Fluid Level: Low Fluid Level |
GO to Pinpoint Test L |
| C0051:64 |
Steering Wheel Position Sensor: Signal Plausibility Failure |
GO to Pinpoint Test LA |
| C0051:67 |
Steering Wheel Position Sensor: Signal Incorrect After Event |
GO to Pinpoint Test LA |
| C0051:85 |
Steering Wheel Position Sensor: Signal Above Allowable Range |
GO to Pinpoint Test LA |
| C0051:96 |
Steering Wheel Position Sensor: Component Internal Failure |
GO to Pinpoint Test LA |
| C0061:28 |
Lateral Acceleration Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test BH |
| C0061:64 |
Lateral Acceleration Sensor: Signal Plausibility Failure |
GO to Pinpoint Test BH |
| C0062:54 |
Longitudinal Acceleration Sensor: Missing Calibration |
GO to Pinpoint Test AN |
| C0062:64 |
Longitudinal Acceleration Sensor: Signal Plausibility Failure |
GO to Pinpoint Test BH |
| C0063:28 |
Yaw Rate Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test BH |
| C0063:64 |
Yaw Rate Sensor: Signal Plausibility Failure |
GO to Pinpoint Test BH |
| C0064:28 |
Roll Rate Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test BH |
| C0064:64 |
Roll Rate Sensor: Signal Plausibility Failure |
GO to Pinpoint Test BH |
| C006B:00 |
Stability System Active Too Long: No Sub Type Information |
GO to Pinpoint Test AD |
| C0072:4B |
Brake Temperature Too High: Over Temperature |
GO to Pinpoint Test X |
| C0078:56 |
Tire Diameter: Invalid/Incompatible Configuration |
GO to Pinpoint Test ZA |
| C052F:00 |
ABS Pump Motor Supply Voltage 'A' Circuit/Open: No Sub Type Information |
GO to Pinpoint Test A |
| C0564:00 |
ABS Control Module System Voltage Low: No Sub Type Information |
GO to Pinpoint Test A |
| C0594:78 |
Brake Booster Motor 'A' Performance: Alignment Or Adjustment Incorrect |
GO to Pinpoint Test CP |
| C0594:92 |
Brake Booster Motor 'A' Performance: Performance Or Incorrect Operation |
GO to Pinpoint Test CP |
| C05CC:00 |
Brake Master Cylinder Piston Position Sensor 'A' Circuit Range/Performance: No Sub Type Information |
GO to Pinpoint Test Z |
| C05CF:00 |
Brake Master Cylinder Piston Position Sensor 'B' Circuit Range/Performance: No Sub Type Information |
GO to Pinpoint Test Z |
| C1013:09 |
Brake System Pressure: Component Failure |
GO to Pinpoint Test CO |
| C1013:7A |
Brake System Pressure: Fluid Leak Or Seal Failure |
GO to Pinpoint Test CO |
| C1013:92 |
Brake System Pressure: Performance Or Incorrect Operation |
GO to Pinpoint Test CO |
| C101F:49 |
Generic Valve Failure: Internal Electronic Failure |
GO to Pinpoint Test Y |
| C1020:00 |
Brake System Fill Not Complete: No Sub Type Information |
GO to Pinpoint Test H |
| C102E:48 |
Stability Control System: Supervision Software Failure |
GO to Pinpoint Test Z |
| C1109:24 |
Vehicle Dynamics Control Switch: Signal Stuck High |
GO to Pinpoint Test E |
| C1A08:1C |
Pressure Sensor Supply: Circuit Voltage Out Of Range |
GO to Pinpoint Test Y |
| C1A95:01 |
Wheel Speed Sensor: General Circuit/Electrical Failure |
GO to Pinpoint Test M |
| C1A95:01 |
Wheel Speed Sensor: General Circuit/Electrical Failure |
GO to Pinpoint Test N |
| C1A95:64 |
Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| P05D3:86 |
Driver Mode Select Switch 'A' Range/Performance: Signal Invalid |
GO to Pinpoint Test BM |
| P0604:8F |
Internal Control Module Random Access Memory (RAM) Error: Erratic |
GO to Pinpoint Test Z |
| U0100:00 |
Lost Communication With ECM/PCM 'A': No Sub Type Information |
GO to Pinpoint Test AI |
| U0102:00 |
Lost Communication with Transfer Case Control Module: No Sub Type Information |
GO to Pinpoint Test AU |
| U0103:00 |
Lost Communication With Gear Shift Control Module A: No Sub Type Information |
GO to Pinpoint Test AV |
| U0122:00 |
Lost Communication With Vehicle Dynamics Control Module: No Sub Type Information |
GO to Pinpoint Test BR |
| U0131:00 |
Lost Communication With Power Steering Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AE |
| U0136:00 |
Lost Communication With Differential Control Module - Rear: No Sub Type Information |
GO to Pinpoint Test AS |
| U0137:00 |
Lost Communication With Trailer Brake Control Module: No Sub Type Information |
GO to Pinpoint Test S |
| U0138:00 |
Lost Communication with All Terrain Control Module: No Sub Type Information |
GO to Pinpoint Test BM |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test D |
| U0146:00 |
Lost Communication With Serial Data Gateway 'A': No Sub Type Information |
GO to Pinpoint Test CI |
| U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test BH |
| U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test AR |
| U0164:00 |
Lost Communication With HVAC Control Module 'A': No Sub Type Information |
GO to Pinpoint Test CE |
| U0212:00 |
Lost Communication With Steering Column Control Module: No Sub Type Information |
GO to Pinpoint Test BV |
| U023A:00 |
Lost Communication With Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test BQ |
| U0253:00 |
Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test CL |
| U0401:00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
GO to Pinpoint Test AI |
| U0401:64 |
Invalid Data Received from ECM/PCM A: Signal Plausibility Failure |
GO to Pinpoint Test AI |
| U0401:86 |
Invalid Data Received from ECM/PCM A: Signal Invalid |
GO to Pinpoint Test AI |
| U0402:86 |
Invalid Data Received from TCM: Signal Invalid |
GO to Pinpoint Test AI |
| U0403:00 |
Invalid Data Received From Transfer Case Control Module: No Sub Type Information |
GO to Pinpoint Test AU |
| U0420:00 |
Invalid Data Received from Power Steering Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AE |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test D |
| U0423:00 |
Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information |
GO to Pinpoint Test AR |
| U0424:86 |
Invalid Data Received from HVAC Control Module 'A': Signal Invalid |
GO to Pinpoint Test CE |
| U0439:00 |
Invalid Data Received From All Terrain Control Module: No Sub Type Information |
GO to Pinpoint Test BM |
| U0439:86 |
Invalid Data Received From All Terrain Control Module: Signal Invalid |
GO to Pinpoint Test BM |
| U0452:02 |
Invalid Data Received From Restraints Control Module: General Signal Failure |
GO to Pinpoint Test BH |
| U0452:41 |
Invalid Data Received From Restraints Control Module: General Checksum Failure |
GO to Pinpoint Test BH |
| U0452:86 |
Invalid Data Received From Restraints Control Module: Signal Invalid |
GO to Pinpoint Test BH |
| U053B:00 |
Invalid Data Received From Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test BQ |
| U0554:86 |
Invalid Data Received From Accessory Protocol Interface Module: Signal Invalid |
GO to Pinpoint Test CL |
| U2001:00 |
Reduced System Function: No Sub Type Information |
GO to Pinpoint Test G |
| U2017:57 |
Control Module Software #2: Invalid/Incompatible Software Component |
GO to Pinpoint Test Z |
| U2017:93 |
Control Module Software #2: No Operation |
GO to Pinpoint Test Z |
| U2018:57 |
Control Module Software #3: Invalid/Incompatible Software Component |
GO to Pinpoint Test Z |
| U202B:61 |
In-Use Application Signing Key: Signal Calculation Failure |
GO to Pinpoint Test Z |
| U202B:62 |
In-Use Application Signing Key: Signal Compare Failure |
GO to Pinpoint Test Z |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test Z |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test Z |
| U2107:00 |
Collision Mitigation By Braking: No Sub Type Information |
GO to Pinpoint Test R |
| U2107:68 |
Collision Mitigation By Braking: Event Information |
GO to Pinpoint Test AQ |
| U2108:68 |
Adaptive Cruise Control: Event Information |
GO to Pinpoint Test AQ |
| U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test Z |
| U3000:00 |
Control Module: No Sub Type Information |
GO to Pinpoint Test Y |
| U3000:04 |
Control Module: System Internal Failure |
GO to Pinpoint Test Y |
| U3000:41 |
Control Module: General Checksum Failure |
GO to Pinpoint Test Y |
| U3000:44 |
Control Module: Data Memory Failure |
GO to Pinpoint Test Y |
| U3000:45 |
Control Module: Program Memory Failure |
GO to Pinpoint Test Y |
| U3000:47 |
Control Module: Watchdog/Safety μC Failure |
GO to Pinpoint Test Y |
| U3000:48 |
Control Module: Supervision Software Failure |
GO to Pinpoint Test Y |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test Y |
| U3000:4B |
Control Module: Over Temperature |
GO to Pinpoint Test Y |
| U3000:52 |
Control Module: Not Activated |
GO to Pinpoint Test Y |
| U3000:96 |
Control Module: Component Internal Failure |
GO to Pinpoint Test Y |
| U3001:68 |
Control Module Improper Shutdown Performance: Event Information |
GO to Pinpoint Test T |
| U3002:62 |
Vehicle Identification Number: Signal Compare Failure |
GO to Pinpoint Test AF |
| U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test A |
| U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test F |
| U300A:29 |
Ignition Switch: Signal Invalid |
GO to Pinpoint Test A |