| B1026:04 |
Steering Column Lock: System Internal Failure |
GO to Pinpoint Test T |
| B1026:05 |
Steering Column Lock: System Programming Failure |
GO to Pinpoint Test U |
| B1026:06 |
Steering Column Lock: Algorithm Based Failure |
GO to Pinpoint Test U |
| B1026:09 |
Steering Column Lock: Component Failure |
GO to Pinpoint Test T |
| B1026:49 |
Steering Column Lock: Internal Electronic Failure |
GO to Pinpoint Test T |
| B1026:51 |
Steering Column Lock: Not Programmed |
GO to Pinpoint Test U |
| B1026:56 |
Steering Column Lock: Invalid/Incompatible Configuration |
GO to Pinpoint Test U |
| B1026:62 |
Steering Column Lock: Signal Compare Failure |
GO to Pinpoint Test T |
| B1026:77 |
Steering Column Lock: Commanded Position Not Reachable |
GO to Pinpoint Test T |
| B1026:87 |
Steering Column Lock: Missing Message |
GO to Pinpoint Test S |
| B1026:92 |
Steering Column Lock: Performance Or Incorrect Operation |
GO to Pinpoint Test S |
| B1026:93 |
Steering Column Lock: No Operation |
GO to Pinpoint Test T |
| B1026:96 |
Steering Column Lock: Component Internal Failure |
GO to Pinpoint Test T |
| B108A:01 |
Start Button: General Circuit/Electrical Failure |
GO to Pinpoint Test G |
| B108A:24 |
Start Button: Signal Stuck High |
GO to Pinpoint Test G |
| B108A:9E |
Start Button: Stuck On |
GO to Pinpoint Test G |
| B10F1:14 |
Key In Switch: Circuit Short To Ground Or Open |
GO to Pinpoint Test F |
| B1142:29 |
Ignition Status 1: Signal Invalid |
GO to Pinpoint Test C |
| B1142:29 |
Ignition Status 1: Signal Invalid |
GO to Pinpoint Test G |
| B1184:11 |
Steering Column Lock Output: Circuit Short To Ground |
GO to Pinpoint Test S |
| B1184:15 |
Steering Column Lock Output: Circuit Short To Battery Or Open |
GO to Pinpoint Test S |
| B1240:11 |
Start Button Mode Indicator: Circuit Short To Ground |
GO to Pinpoint Test H |
| B1240:15 |
Start Button Mode Indicator: Circuit Short To Battery Or Open |
GO to Pinpoint Test H |
| B1240:15 |
Start Button Mode Indicator: Circuit Short To Battery Or Open |
GO to Pinpoint Test I |
| B1310:12 |
Run/Start Control: Circuit Short To Battery |
GO to Pinpoint Test C |
| B1310:12 |
Run/Start Control: Circuit Short To Battery |
GO to Pinpoint Test G |
| B1310:14 |
Run/Start Control: Circuit Short To Ground Or Open |
GO to Pinpoint Test C |
| B1310:14 |
Run/Start Control: Circuit Short To Ground Or Open |
GO to Pinpoint Test G |
| U300A:01 |
Ignition Switch: General Circuit/Electrical Failure |
GO to Pinpoint Test L |
| P2530:00 |
Ignition Switch Run Position Circuit: No Sub Type Information |
GO to Pinpoint Test C |
| P2530:00 |
Ignition Switch Run Position Circuit: No Sub Type Information |
GO to Pinpoint Test G |
| P2534:00 |
Ignition Switch On/Start Position 'A' Circuit Low: No Sub Type Information |
GO to Pinpoint Test C |
| P2534:00 |
Ignition Switch On/Start Position 'A' Circuit Low: No Sub Type Information |
GO to Pinpoint Test G |
| P2535:00 |
Ignition Switch On/Start Position 'A' Circuit High: No Sub Type Information |
GO to Pinpoint Test C |
| P2535:00 |
Ignition Switch On/Start Position 'A' Circuit High: No Sub Type Information |
GO to Pinpoint Test G |
| B112B:04 |
Steering Wheel Module: System Internal Failure |
GO to Pinpoint Test K |
| B112B:44 |
Steering Wheel Module: Data Memory Failure |
GO to Pinpoint Test K |
| B112B:45 |
Steering Wheel Module: Program Memory Failure |
GO to Pinpoint Test K |
| B112B:46 |
Steering Wheel Module: Calibration/Parameter Memory Failure |
GO to Pinpoint Test K |
| B112B:49 |
Steering Wheel Module: Internal Electronic Failure |
GO to Pinpoint Test K |
| B11D9:16 |
Vehicle Battery: Circuit Voltage Below Threshold |
GO to Pinpoint Test Q |
| B11D9:17 |
Vehicle Battery: Circuit Voltage Above Threshold |
GO to Pinpoint Test R |
| B135C:11 |
Heater Element: Circuit Short To Ground |
GO to Pinpoint Test J |
| B135C:13 |
Heater Element: Circuit Open |
GO to Pinpoint Test J |
| U0140:08 |
Lost Communication With Body Control Module: Bus Signal / Message Failure |
GO to Pinpoint Test M |
| U0146:08 |
Lost Communication With Serial Data Gateway 'A': Bus Signal / Message Failure |
GO to Pinpoint Test M |
| U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test M |
| U0155:08 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: Bus Signal / Message Failure |
GO to Pinpoint Test N |
| U0164:00 |
Lost Communication With HVAC Control Module 'A': No Sub Type Information |
GO to Pinpoint Test N |
| U023A:08 |
Lost Communication With Image Processing Module A: Bus Signal / Message Failure |
GO to Pinpoint Test N |
| U0241:08 |
Lost Communication With Headlamp Control Module 'A': Bus Signal / Message Failure |
GO to Pinpoint Test N |
| U0422:08 |
Invalid Data Received From Body Control Module: Bus Signal / Message Failure |
GO to Pinpoint Test O |
| U053B:08 |
Invalid Data Received From Image Processing Module A: Bus Signal / Message Failure |
GO to Pinpoint Test O |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test P |
| U210A:11 |
Temperature Sensor: Circuit Short To Ground |
GO to Pinpoint Test J |
| U210A:13 |
Temperature Sensor: Circuit Open |
GO to Pinpoint Test J |
| U210A:29 |
Temperature Sensor: Signal Invalid |
GO to Pinpoint Test J |
| U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test P |