Removal & Installation
WARNING: This page is about the Yukon 2D Utility, 5.7 K, 4WD, Automatic, which is a different variant/trim than selected.
TRANS ID - 4L80E
| Applies To | Note | Standard Hours | Warranty Hours | Skill Level |
|---|
| 4WD | | 7.0 | 4.9 | C |
| Additional Procedure: TRANSMISSION ASSEMBLY: Removal & Installation: |
| 4WD, w/Skid Plate add | | 0.3 | | C |
| w/Engine to Transmission Braces add | | 0.3 | | C |
| Combination Procedure: BAND: Remove & Replace: |
| Front | | 0.7 | | A |
| Rear or Both | | 1.7 | | A |
| Combination Procedure: CLUTCH PLATES: Remove & Replace: |
| Direct | | 1.1 | | A |
| Forward | | 1.1 | | A |
| Forward & Direct | | 1.5 | | A |
| Fourth Speed | | 1.0 | | A |
| Intermediate | | 1.1 | | A |
| Intermediate & Direct | | 1.5 | | A |
| Overrun | | 0.9 | | A |
| Combination Procedure: CONVERTER: Drain & Test: |
| | 0.2 | | C |
| Combination Procedure: FLYWHEEL: Remove & Replace: |
| | 0.3 | | C |
| Combination Procedure: OUTPUT SHAFT: Remove & Replace: |
| | 2.2 | | B |
| Combination Procedure: TORQUE CONVERTER: Remove & Replace: |
| | 0.1 | | C |
| Combination Procedure: TRANS OIL PUMP: Overhaul Removed: |
| | 0.5 | | B |
| Combination Procedure: TRANS OIL PUMP: Remove & Replace: |
| | 0.4 | | B |
| Combination Procedure: TRANS OIL PUMP BUSHINGS & SEAL: Remove & Replace: |
| | 0.3 | | B |
| Combination Procedure: TRANS OIL PUMP SEAL: Remove & Replace: |
| | 0.2 | | B |
| Combination Procedure: TRANSFER CASE ASSEMBLY: Overhaul: |
| | 2.5 | | A |
| Combination Procedure: TRANSFER CASE ASSEMBLY: Replace: |
| 4WD | | 0.3 | | C |
| Combination Procedure: TRANSMISSION ASSEMBLY: Replace: |
| | 0.6 | | C |
| Combination Procedure: TRANSMISSION CASE: Remove & Replace: |
| | 2.5 | | A |
TRANS ID - 700-R4, 4L60, 4L60E, 4L65E, 4L70E
| Applies To | Note | Standard Hours | Warranty Hours | Skill Level |
|---|
| 4WD | | 5.7 | | C |
| Additional Procedure: TRANSMISSION ASSEMBLY: Removal & Installation: |
| w/Skid Plate add | | 0.3 | 0.3 | C |
| Where Transmission Crossmember interferes add | | 0.7 | | C |
| Combination Procedure: CONVERTER: Drain & Test: |
| | 0.2 | | C |
| Combination Procedure: FLYWHEEL: Remove & Replace: |
| | 0.3 | | C |
| Combination Procedure: TORQUE CONVERTER: Remove & Replace: |
| | 0.1 | | C |
| Combination Procedure: TRANS OIL PUMP: Overhaul Removed: |
| | 0.5 | | B |
| Combination Procedure: TRANS OIL PUMP: Remove & Replace: |
| | 1.1 | | B |
| Combination Procedure: TRANS OIL PUMP BUSHINGS & SEAL: Remove & Replace: |
| | 0.3 | | B |
| Combination Procedure: TRANS OIL PUMP SEAL: Remove & Replace: |
| | 0.2 | | B |
| Combination Procedure: TRANSFER CASE ASSEMBLY: Overhaul: |
| T/Case Mfr New Process/New Venture,T/Case Mfr CD 231C | | 2.8 | | A |
| T/Case Mfr New Process/New Venture,T/Case Mfr CD 233C | | 1.6 | | A |
| Combination Procedure: TRANSFER CASE ASSEMBLY: Replace: |
| | 0.3 | | C |
| Combination Procedure: TRANSMISSION ASSEMBLY: Replace: |
| | 0.6 | | C |
| Combination Procedure: TRANSMISSION HOUSING: Remove & Replace: |
| | 3.6 | | A |