DTC P2183: ECT Sensor 2 Range/ Performance Problem
- Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information (see GENERAL TROUBLESHOOTING INFORMATION ).
- If DTC P0111 is stored at the same time as DTC P2183, troubleshoot DTC P0111 first, then recheck for DTC P2183.
- Check for poor connections or loose terminals at ECT sensor 1 and ECT sensor 2.
Are the connections and terminals OK?
YES - Go to step 2.
NO - Repair the connectors or terminals, then go to step 27.
- Turn the ignition switch ON (II).
- Check for Temporary DTCs or DTCs with the HDS.
Are DTC P1116 and P2183 indicated at the same time?
YES - Go to step 15.
NO - Go to step 4.
- Start the engine, and let it idle 10 minutes.
- Check ECT SENSOR 2 in the DATA LIST with the HDS.
Is about 131°F (55°C) or less, or 1.50 V or more indicated?
YES - Replace ECT sensor 2 (see ECT SENSOR 2 REPLACEMENT ), then go to step 27.
NO - Go to step 6.
- Turn the ignition switch OFF.
- Drain the coolant (see COOLANT CHECK ).
- Remove ECT sensor 2 (see ECT SENSOR 2 REPLACEMENT ).
- Allow ECT sensor 2 to cool to ambient temperature.
- Note the ambient temperature.
- Connect ECT sensor 2 to its 2P connector, but do not install it on the engine.
- Turn the ignition switch ON (II).
- Note the value of ECT SENSOR 2 quickly in the DATA LIST with the HDS.
- Compare the value of ECT SENSOR 2 and the ambient temperature.
Does ECT SENSOR 2 differ 5.4°F (3°C) or more?
YES - Replace ECT sensor 2 (see ECT SENSOR 2 REPLACEMENT ), then go to step 27.
NO - Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at ECT sensor 1, ECT sensor 2, and the ECM/PCM.
- Start the engine, and let it idle 10 minutes.
- Check ECT SENSOR 1 in the DATA LIST with the HDS.
Is about 118°F (48°C) or less, or 1.75 V or more indicated?
YES - Replace ECT sensor 1 (see ECT SENSOR 1 REPLACEMENT ), then go to step 27.
NO - Go to step 17.
- Let the engine idle 10 minutes.
- Check ECT SENSOR 2 in the DATA LIST with the HDS.
Is about 131°F (55°C) or less, or 1.50 V or more indicated?
YES - Replace ECT sensor 2 (see ECT SENSOR 2 REPLACEMENT ), then go to step 27.
NO - Go to step 19.
- Turn the ignition switch OFF.
- Drain the coolant (see COOLANT CHECK ).
- Remove ECT sensor 1 (see ECT SENSOR 1 REPLACEMENT ) and ECT sensor 2 (see ECT SENSOR 2 REPLACEMENT ).
- Allow the sensors to cool to ambient temperature.
- Note the ambient temperature.
- Connect ECT sensor 1 to its 2P connector, and ECT sensor 2 to the 2P connector, but do not install them on the engine.
- Note the value of ECT SENSOR 1 and ECT SENSOR 2 quickly in the DATA LIST with the HDS.
- Compare the value of ECT SENSOR 1 and the ambient temperature, and the value of ECT SENSOR 2 and the ambient temperature individually.
Does one of the sensors differ more than 5.4°F (3°C) from the ambient temperature?
YES - Replace the sensor that differed more than 5.4°F (3°C) from the ambient temperature, then go to step 27.
NO - Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at ECT sensor 1, ECT sensor 2, and the ECM/PCM.
- Turn the ignition switch ON (II).
- Reset the ECM/PCM with the HDS.
- Do the ECM/PCM idle learn procedure (see ECM/PCM IDLE LEARN PROCEDURE ).
- Check for Temporary DTCs or DTCs with the HDS.
Is DTC P2183 indicated?
YES - Check for poor connections or loose terminals at ECT sensor 1, ECT sensor 2, and the ECM/PCM, then go to step 1.
NO - Troubleshooting is complete. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTCs troubleshooting.