LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Hummer >> 2008 >> H3 Base, Automatic >> Repair and Diagnosis >> Accessories & Equipment >> Collision/Avoidance >> Object Detection >> Diagnostic Information and Procedures >> Front Vision Camera System Malfunction >> Circuit/System Testing
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Circuit/System Testing

Front Vision System Always On

  1. Ignition OFF, disconnect the harness connector at the frontview camera switch.
  2. Ignition ON, verify that a test lamp does not illuminate between the frontview camera switch control circuit terminal B and ground
    • If the test lamp illuminates, test the control circuit for a short to voltage.
  3. If all circuits test normal, replace the frontview camera switch.

LCD Always Deployed

  1. Ignition OFF, disconnect the harness connector at the ISRVM.
  2. Ignition ON, frontview camera switch OFF, verify a test lamp does not illuminate between the control circuit terminal 9 and ground.
    • If the test lamp does illuminate, test the control circuit for a short to voltage.
  3. If all circuits test normal, test or replace the ISRVM.

Front Vision System Does Not Display

  1. Ignition OFF, disconnect the harness connector at the frontview camera.
  2. Test for less than 1.0 ohm between the ground circuit terminal B and ground.
    • If greater than the specified range, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the frontview camera image display module.
  3. Ignition ON, frontview camera switch ON, test for 5.8-6.2 volts between the 6-volt reference circuit terminal A and ground.
    • If less than the specified range, test the reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the frontview camera image display module.
    • If greater than the specified range, test the reference circuit for a short to voltage. If the circuit tests normal, replace the frontview camera image display module.
  4. Ignition OFF, test for greater than 1.0 ohm between the camera video signal circuit terminal C and ground.
    • If less than the specified range, test the signal circuit for a short to ground. If the circuit tests normal, replace the frontview camera image display module.
  5. Ignition ON, verify that a test lamp does not illuminate between the camera video signal circuit terminal C and ground.
    • If the test lamp illuminates, test the signal circuit for a short to voltage. If the circuit tests normal, replace the frontview camera image display module.
  6. Ignition OFF, disconnect the frontview camera module.
  7. Test for less than 3.0 ohms along the signal circuit terminal C to terminal 9.
    • If greater than the specified range, test the signal circuit for an open/high resistance.
  8. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 2 and ground.
    • If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.
  9. Verify that a test lamp illuminates between the ignition circuit terminal 2 and the ground circuit terminal 3.
    • If the test lamp does not illuminate, test the ground circuit for an open/high resistance.
  10. Frontview camera switch ON, verify that a test lamp illuminates between the control circuit terminal 1 and ground.
    • If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the frontview camera switch.
  11. Ignition OFF, test for greater than 1.0 ohm between the camera video signal circuit terminal 11 and ground.
    • If less than the specified range, test the signal circuit for a short to ground. If the circuit tests normal, replace the ISRVM.
  12. Ignition ON, verify that a test lamp does not illuminate between the camera video signal circuit terminal 11 and ground.
    • If the test lamp illuminates, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ISRVM.
  13. Ignition OFF, test for greater than 1.0 ohm between the camera video signal circuit terminal 12 and ground.
    • If less than the specified range, test the signal circuit for a short to ground. If the circuit tests normal, replace the ISRVM.
  14. Ignition ON, verify that a test lamp does not illuminate between the camera video signal circuit terminal 12 and ground.
    • If the test lamp illuminates, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ISRVM.
  15. Ignition OFF, disconnect the harness connector at the ISRVM.
  16. Test for less than 1.0 ohm along the signal circuit terminal 11 to terminal 2.
    • If greater than the specified range, test the signal circuit for an open/high resistance.
  17. Test for less than 1.0 ohm along the signal circuit terminal 12 to terminal 1.
    • If greater than the specified range, test the signal circuit for an open/high resistance.
  18. If all circuits test normal, replace the frontview camera module.

LCD Will Not Deploy

  1. Ignition OFF, disconnect the harness connector at the ISRVM.
  2. Ignition OFF, test for less than 1 ohm of resistance between the ground circuit terminal 8 and ground.
    • If greater than the specified range, test the ground circuit for an open/high resistance.
  3. Ignition ON, verify a test lamp illuminates between the ignition circuit terminal 13 and ground.
    • If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.
  4. Ignition ON, frontview camera switch ON, verify that a test lamp illuminates between the control circuit terminal 9 and ground.
    • If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the frontview camera switch.
  5. If all circuits test normal, test or replace the ISRVM.
scientia non olet · About LEMON Manuals