Repair Procedures: Removal

Engine cover.
(Refer to Engine Mechanical System - "ENGINE COVER ")
Air cleaner assembly and air duct.
(Refer to Engine Mechanical System - "AIR CLEANER ")
Battery and battery tray.
(Refer to Engine Electrical System - "BATTERY ")
Remove the ground line after removing the bolt (A).

Fig 1: Removing Ground Line Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Disconnect the solenoid valve connector (A) and inhibitor switch connector (B).

Fig 2: Disconnecting Solenoid Valve Connector And Inhibitor Switch Connector
Courtesy of HYUNDAI MOTOR AMERICA
Remove the control cable (B) after removing the nut (C) and the bolt (A).
Tightening torque:

(C) 7.8 ~ 11.8 N.m (1.0 ~ 1.5 kgf.m, 5.8 ~ 8.7 lb-ft)

(A) 14.7 ~21.6 N.m (1.5 ~ 2.2 kgf.m, 10.9 ~ 15.9 lb-ft)

Fig 3: Removing Control Cable Nut And Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Remove the wiring bracket installation bolt (A).

Fig 4: Removing Wiring Bracket Installation Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Remove the Crankshaft Position Sensor (CKPS) sensor (A).

Fig 5: Removing Crankshaft Position Sensor (CKPS) Sensor
Courtesy of HYUNDAI MOTOR AMERICA
Disconnect the hose (B) after removing the automatic transaxle fluid cooler hose clamp (A).

Fig 6: Removing Automatic Transaxle Fluid Cooler Hose Clamp
Courtesy of HYUNDAI MOTOR AMERICA
Remove the wiring bracket installation bolt (A) and clip (B).

Fig 7: Removing Wiring Bracket Installation Bolt And Clip
Courtesy of HYUNDAI MOTOR AMERICA
After assembling the T-shaped beam, install the supporter (SST No: 09200-2S200) to the beam of SST (09200-38001, 09200-3N000).
Install the adaptor (SST No: 09200-2P100) to the beam of (SST No: 09200-38001, 09200-3N000).
Install the assembled SST (A) on the engine room.
Hang the ring (B) on the engine hanger, support the engine.
NOTE: To prevent slip, the support supports the body securely.

Fig 8: Removing SST On Engine Room
Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle upper mounting bolt (A) and the starter motor mounting bolt (B).
Tightening torque:

(A): 63.7 ~ 83.4 N.m (6.5 ~ 8.5 kgf.m, 47.0 ~ 61.5 lb-ft)

(B): 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

Fig 9: Removing Automatic Transaxle Upper Mounting Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Remove the cover (A).

Fig 10: Removing Cover
Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle support bracket mounting bolt (A).
Tightening torque:

88.2 ~ 107.8 N.m (9.0 ~ 11.0 Kgf.m, 65 ~ 79.5 lb-ft)

Fig 11: Removing Automatic Transaxle Support Bracket Mounting Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle mounting support bracket (A).
Tightening torque:

(A) 58.8 ~ 78.4 N.m (6.0 ~ 8.0 kgf.m, 43.3 ~ 57.8 lb-ft)

Fig 12: Removing Automatic Transaxle Mounting Support Bracket
Courtesy of HYUNDAI MOTOR AMERICA
Lift the vehicle with a jack.
Remove the under cover (A).
Tightening torque:

7.8 ~ 11.7 N.m (0.8 ~ 1.2 kgf.m, 5.7 ~ 8.6 lb-ft)

Fig 13: Removing Under Cover
Courtesy of HYUNDAI MOTOR AMERICA
Drive shaft assembly.
(Refer to Driveshaft and axle - "FRONT DRIVESHAFT ")
Front muffler assembly.
(Refer to Engine Mechanical System - "FRONT MUFFLER ")
Loosen the bolt (A) & nut (B) and then remove the roll rod stopper (C).
Tightening torque:

(A) 107.9 ~ 127.5 N.m (11.0 ~ 13.0 kgf.m, 79.6 ~ 94.0 lb-ft)

(B) 49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)

Fig 14: Removing Roll Rod Stopper
Courtesy of HYUNDAI MOTOR AMERICA
Remove the dust cover (A).
Tightening torque:

9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

Fig 15: Removing Dust Cover
Courtesy of HYUNDAI MOTOR AMERICA
Remove the torque converter mounting bolt (A-6ea) with rotating the crankshaft.
Tightening torque:

45.1 ~ 52.0 N.m (4.6 ~ 5.3 kgf.m, 33.3 ~ 38.3 lb-ft)

Fig 16: Removing Torque Converter Mounting Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle with a jack after removing the mounting bolt (B-4ea, C-1ea).
Tightening torque:

(B) 39.2 ~ 46.1 N.m (4.0 ~ 4.7 kgf.m, 28.9 ~ 34.0 lb-ft)

(C) 78.5 ~ 98.1 N.m (8.0 ~ 10.0 kgf.m, 57.9 ~ 72.3 lb-ft)

Fig 17: Removing Automatic Transaxle With Jack
Courtesy of HYUNDAI MOTOR AMERICA
Remove the start motor mounting bolt (A).
Tightening torque:

42.2 ~ 53.9 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

Fig 18: Removing Start Motor Mounting Bolt
Courtesy of HYUNDAI MOTOR AMERICA