LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2007 >> QX56 AWD >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System - Component Testing >> ICC Brake Switch >> Diagnostic Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnostic Procedure

  1. CHECK OVERALL FUNCTION-I 

    With CONSULT-II 

    1. Turn ignition switch ON.
    2. Select "BRAKE SW1" in "DATA MONITOR" mode with CONSULT-II.
    3. Check "BRAKE SW1" indication under the following conditions.
      DATA MONITOR CHART

      CONDITION INDICATION
      Brake pedal: Slightly depressed OFF
      Brake pedal: Fully released ON
      Fig 1: CONSULT-II Display - Data Monitor
      G04900669Courtesy of NISSAN NORTH AMERICA, INC.

    Without CONSULT-II 

    1. Turn ignition switch ON.
    2. Check voltage between ECM terminal 108 and ground under the following conditions.
      TERMINALS VOLTAGE CHART

      CONDITION VOLTAGE
      Brake pedal: Slightly depressed Approximately 0V
      Brake pedal: Fully released Battery voltage
      Fig 2: Checking Voltage Between ECM Terminal 108 (ASCD Brake Switch Signal) And Ground
      G04900670Courtesy of NISSAN NORTH AMERICA, INC.

    OK or NG 

    OK: GO TO 2.

    NG: GO TO  3.

  2. CHECK OVERALL FUNCTION-II 

    With CONSULT-II 

    Check "BRAKE SW2" indication in "DATA MONITOR" mode.

    DATA MONITOR REFERENCE CHART

    CONDITION INDICATION
    Brake pedal: Fully released OFF
    Brake pedal: Slightly depressed ON
    Fig 3: CONSULT-II Display - Data Monitor
    G04900671Courtesy of NISSAN NORTH AMERICA, INC.

    Without CONSULT-II 

    Check voltage between ECM terminal 101 and ground under the following conditions.

    TERMINALS VOLTAGE CHART

    CONDITION VOLTAGE
    Brake pedal: Fully released Approximately 0V
    Brake pedal: Slightly depressed Battery voltage
    Fig 4: Checking Voltage Between ECM Terminal 101 And Ground
    G04875395Courtesy of NISSAN NORTH AMERICA, INC.

    OK or NG 

    OK: INSPECTION END 

    NG: GO TO  10.

  3. CHECK DTC WITH ICC UNIT 

    Refer to "TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS ".

    OK or NG 

    OK: GO TO 4.

    NG: Repair or replace.

  4. CHECK ICC BRAKE HOLD RELAY POWER SUPPLY CIRCUIT 
    1. Turn ignition switch OFF.
    2. Disconnect ICC brake hold relay.
    3. Turn ignition switch ON.
      Fig 5: Identifying ICC Brake Hold Relay
      G05229051Courtesy of NISSAN NORTH AMERICA, INC.
    4. Check voltage between ICC brake hold relay terminal 4 and ground with CONSULT-II or tester.

      Voltage: Battery voltage 

      Fig 6: Checking Voltage Between ICC Brake Hold Relay Terminal 4 And Ground
      G05229052Courtesy of NISSAN NORTH AMERICA, INC.

    OK or NG 

    OK: GO TO  6.

    NG: GO TO 5.

  5. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors M31, E152
    • Fuse block (J/B) connector M4
    • 10A fuse
    • Harness for open or short between ICC brake hold relay and fuse

      Repair open circuit or short to ground or short to power in harness or connectors.

  6. CHECK ICC BRAKE SWITCH POWER SUPPLY CIRCUIT 
    1. Turn ignition switch OFF.
    2. Disconnect ICC brake switch harness connector.
    3. Check harness continuity between ICC brake hold relay terminal 3 and ICC brake switch terminal 1.

      Refer to WIRING DIAGRAM .

      Continuity should exist. 

      Fig 7: Identifying ICC Brake Switch Harness Connector
      G05229044Courtesy of NISSAN NORTH AMERICA, INC.
    4. Also check harness for short to ground and short to power.

    OK or NG 

    OK: GO TO 7.

    NG: Repair open circuit or short to ground or short to power in harness or connectors.

  7. CHECK ICC BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT 
    1. Disconnect ECM harness connector.
    2. Check harness continuity between ICC brake switch terminal 2 and ECM terminal 108.

      Refer Wiring Diagram.

      Continuity should exist. 

    3. Also check harness for short to ground and short to power.

    OK or NG 

    OK: GO TO 8.

    NG: Repair open circuit or short to ground or short to power in harness or connectors.

  8. CHECK ICC BRAKE HOLD RELAY 

    Refer to "COMPONENT INSPECTION ".

    OK: GO TO 9.

    NG: Replace ICC brake hold relay.

  9. CHECK ICC BRAKE SWITCH 

    Refer to "COMPONENT INSPECTION ".

    OK or NG 

    OK: GO TO  14.

    NG: Replace ICC brake switch.

  10. CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT 
    1. Turn ignition switch OFF.
    2. Disconnect stop lamp switch harness connector.
      Fig 8: Identifying Stop Lamp Switch Harness Connector
      G05229044Courtesy of NISSAN NORTH AMERICA, INC.
    3. Check voltage between stop lamp switch terminal 3 and ground with CONSULT-II or tester.

      Voltage: Battery voltage 

      Fig 9: Checking Voltage Between Stop Lamp Switch Terminal 3 And Ground
      G04920627Courtesy of NISSAN NORTH AMERICA, INC.

    OK or NG 

    OK: GO TO  12.

    NG: GO TO 11.

  11. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors M31, E152
    • Fuse block (J/B) No. 1 connector M60
    • 10A fuse
    • Harness for open or short between stop lamp switch and battery

      Repair open circuit or short to ground or short to power in harness or connectors.

  12. CHECK STOP LAMP SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT 
    1. Disconnect ECM harness connector.
    2. Check harness continuity between ECM terminal 101 and stop lamp switch terminal 4.

      Refer to WIRING DIAGRAM .

      Continuity should exist. 

    3. Also check harness for short to ground and short to power.

    OK or NG 

    OK: GO TO 13.

    NG: Repair open circuit or short to ground or short to power in harness or connectors.

  13. CHECK STOP LAMP SWITCH 

    Refer to "COMPONENT INSPECTION ".

    OK or NG 

    OK: GO TO 14.

    NG: Replace stop lamp switch.

  14. CHECK INTERMITTENT INCIDENT 

    Refer to "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".

    INSPECTION END 

scientia non olet · About LEMON Manuals