Diagnosis Procedure

1. Turn ignition switch OFF.
2. Check ground connection M95. Refer to Ground Inspection in "CIRCUIT INSPECTION ".

Is the inspection result normal? 

YES: GO TO 2.

NO: Repair or replace ground connection.

1. Disconnect EVAP control system pressure sensor harness connector.
2. Check sensor harness connector for water.

   Water should not exist. 

Is the inspection result normal? 

YES: GO TO 3.

NO: Repair or replace harness connector.

1. Turn ignition switch ON.
2. Check the voltage between EVAP control system pressure sensor harness connector and ground.
   VOLTAGE SPECIFICATIONS
   
   

   EVAP control system pressure sensor		Ground	Voltage (V)
   Connector	Terminal
   B252	3	Ground	Approx. 5

Is the inspection result normal? 

YES: GO TO  10.

NO: GO TO 4.

1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between EVAP control system pressure sensor harness connector and ECM harness connector.
   CONTINUITY SPECIFICATIONS
   
   

   EVAP control system pressure sensor		ECM		Continuity
   Connector	Terminal	Connector	Terminal
   B252	3	M107	107	Existed

Is the inspection result normal? 

YES: GO TO  6.

NO: GO TO 5.

Check the following.

• Harness connectors B201, M117
• Harness for open between ECM and EVAP control system pressure sensor

  Repair open circuit.

Check harness for short to power and short to ground, between the following terminals.

Is the inspection result normal? 

YES: GO TO 7.

NO: Repair short to ground or short to power in harness or connectors.

Check the following.

• Crankshaft position sensor (POS) (Refer to "COMPONENT INSPECTION ".)
• Camshaft position sensor (PHASE) (bank 2) (Refer to "COMPONENT INSPECTION ".)
• Exhaust valve timing control position sensor (bank 2) (Refer to "COMPONENT INSPECTION ".)
• Battery current sensor (Refer to "COMPONENT INSPECTION ".)
• Refrigerant pressure sensor (Refer to "DIAGNOSIS PROCEDURE ".)

Is the inspection result normal? 

YES: GO TO 8.

NO: Replace malfunctioning component.

Refer to "COMPONENT INSPECTION ".

Is the inspection result normal? 

YES: GO TO  15.

NO: GO TO 9.

1. Replace accelerator pedal assembly
2. Go to "SPECIAL REPAIR REQUIREMENT ".

   INSPECTION END

1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between EVAP control system pressure sensor harness connector and ECM harness connector.
   CONTINUITY SPECIFICATIONS
   
   

   EVAP control system pressure sensor		ECM		Continuity
   Connector	Terminal	Connector	Terminal
   B252	1	M107	112	Existed

4. Also check harness for short to ground and short to power.

Is the inspection result normal? 

YES: GO TO  12.

NO: GO TO 11.

Check the following.

• Harness connectors B201, M117
• Harness for open or short between EVAP control system pressure sensor and ECM

  Repair open circuit or short to ground or short to power in harness or connectors.

1. Check the continuity between EVAP control system pressure sensor harness connector and ECM harness connector.
   CONTINUITY SPECIFICATIONS
   
   

   EVAP control system pressure sensor		ECM		Continuity
   Connector	Terminal	Connector	Terminal
   B252	2	M107	102	Existed

2. Also check harness for short to ground and short to power.

Is the inspection result normal? 

YES: GO TO  14.

NO: GO TO 13.

Check the following.

• Harness connectors B201, M117
• Harness for open or short between EVAP control system pressure sensor and ECM

  Repair open circuit or short to ground or short to power in harness or connectors.

Refer to "COMPONENT INSPECTION ".

Is the inspection result normal? 

YES: GO TO 15.

NO: Replace EVAP control system pressure sensor.

Refer to "INTERMITTENT INCIDENT ".

INSPECTION END