LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2008 >> EX35 Base, AWD >> Repair and Diagnosis >> Engine Performance >> Engine Control Systems >> Engine Control System - DTCS U1000 To P0153 >> P0102, P0103, P010C, P010D MAF Sensor >> Diagnosis Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnosis Procedure

  1. INSPECTION START

    Confirm the detected DTC.

    Which DTC is detected? 

    P0102, P010C: GO TO 2.

    P0103, P010D: GO TO  3.

  2. CHECK INTAKE SYSTEM

    Check the following for connection.

    • Air duct
    • Vacuum hoses
    • Intake air passage between air duct to intake manifold

    Is the inspection result normal? 

    YES: GO TO 3.

    NO: Reconnect the parts.

  3. CHECK GROUND CONNECTION
    1. Turn ignition switch OFF.
    2. Check ground connection M95. Refer to Ground Inspection in "CIRCUIT INSPECTION ".

    Is the inspection result normal? 

    YES: GO TO 4.

    NO: Repair or replace ground connection.

  4. CHECK MAF SENSOR POWER SUPPLY CIRCUIT
    1. Disconnect mass air flow (MAF) sensor harness connector.
    2. Turn ignition switch ON.
    3. Check the voltage between MAF sensor harness connector and ground.
      VOLTAGE SPECIFICATIONS

      DTC MAF sensor Ground Voltage
      Bank Connector Terminal
      P0102, P0103 1 F31 5 Ground Battery voltage
      P010C, P010D 2 F42 5

    Is the inspection result normal? 

    YES: GO TO  6.

    NO: GO TO 5.

  5. DETECT MALFUNCTIONING PART

    Check the following.

    • Harness connectors E106, M6
    • Harness connectors M116, F103
    • Harness for open or short between mass air flow sensor and ECM
    • Harness for open or short between mass air flow sensor and IPDM E/R

      Repair open circuit or short to ground or short to power in harness or connectors.

  6. CHECK MAF SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check the continuity between MAF sensor harness connector and ECM harness connector.
      CONTINUITY SPECIFICATIONS

      DTC MAF sensor ECM Continuity
      Bank Connector Terminal Connector Terminal
      P0102, P0103 1 F31 4 F102 68 Existed
      P010C, P010D 2 F42 4 94
    4. Also check harness for short to ground and short to power.

    Is the inspection result normal? 

    YES: GO TO 7.

    NO: Repair open circuit or short to ground or short to power in harness or connectors.

  7. CHECK MAF SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
    1. Check the continuity between MAF sensor harness connector and ECM harness connector.
      CONTINUITY SPECIFICATIONS

      DTC MAF sensor ECM Continuity
      Bank Connector Terminal Connector Terminal
      P0102, P0103 1 F31 3 F102 77 Existed
      P010C, P010D 2 F42 3 79
    2. Also check harness for short to ground and short to power.

    Is the inspection result normal? 

    YES: GO TO 8.

    NO: Repair open circuit or short to ground or short to power in harness or connectors.

  8. CHECK MASS AIR FLOW SENSOR

    Refer to "COMPONENT INSPECTION ".

    Is the inspection result normal? 

    YES: GO TO 9.

    NO: Replace malfunctioning mass air flow sensor.

  9. CHECK INTERMITTENT INCIDENT

    Refer to "INTERMITTENT INCIDENT ".

    INSPECTION END

scientia non olet · About LEMON Manuals