| B2013: ID DISCORD BCM-S/L |
Inhibit setting the vehicle to READY |
When communication between BCM and steering lock unit are communicated normally. |
| B2014: CHAIN OF S/L-BCM |
Inhibit setting the vehicle to READY |
When communication between BCM and steering lock unit are communicated normally. |
| B2192: ID DISCORD BCM-ECM |
Inhibit setting the vehicle to READY |
Erase DTC |
| B2193: CHAIN OF BCM-ECM |
Inhibit setting the vehicle to READY |
Erase DTC |
| B2195: ANTI-SCANNING |
Inhibit setting the vehicle to READY |
Ignition switch ON → OFF |
| B2196: DONGLE NG |
Inhibit setting the vehicle to READY |
Erase DTC |
| B2198: NATS ANTENNA AMP |
Inhibit setting the vehicle to READY |
Erase DTC |
| B2557: VEHICLE SPEED |
Inhibit steering lock |
When the following CAN signal status (vehicle speed signal) becomes consistent
- Vehicle speed signal (ABS)
- Vehicle speed signal (Meter)
|
| B2601: SHIFT POSITION |
Inhibit steering lock |
500 ms after the following signal reception status becomes consistent
- P position switch signal
- P range signal (CAN)
|
| B2602: SHIFT POSITION |
Inhibit steering lock |
5 seconds after the following BCM recognition conditions are fulfilled
- Ignition switch is in the ON position
- P position switch signal: Except P position (battery voltage)
- Vehicle speed: 4 km/h (2.5 MPH) or more
|
| B2603: SHIFT POSI STATUS |
Inhibit steering lock |
500 ms after any of the following BCM recognition conditions are fulfilled
- Status 1
- Ignition switch is in the ON position
- P position switch signal: Except P position (12 V)
- P/N position signal: Except P and N positions (0 V)
- Status 2
- Ignition switch is in the ON position
- P position switch signal: P position (0 V)
- P/N position signal: P or N positions (12 V)
|
| B2604: PNP/CLUTCH SW |
Inhibit steering lock |
500 ms after any of the following BCM recognition conditions are fulfilled
- Status 1
- Ignition switch is in the ON position
- P/N position signal: P or N position (12 V)
- Shift position signal (CAN): P or N position
- Status 2
- Ignition switch is in the ON position
- P/N position signal: Except P and N positions (0 V)
- Shift position signal (CAN): Except P and N position
|
| B2609: S/L STATUS |
- Inhibit setting the vehicle to READY
- Inhibit steering lock
|
When the following steering lock conditions agree
- BCM steering lock control status
- Steering lock condition No. 1 signal status
- Steering lock condition No. 2 signal status
|
| B260B: STEERING LOCK UNIT |
Inhibit steering lock |
Erase DTC |
| B260D: STEERING LOCK UNIT |
Inhibit steering lock |
Erase DTC |
| B2612: S/L STATUS |
- Inhibit setting the vehicle to READY
- Inhibit steering lock
|
When any of the following conditions are fulfilled
- Steering lock unit status signal (CAN) is received normally
- The BCM steering lock control status matches the steering lock status recognized by the steering lock unit status signal (CAN from IPDM E/R)
|
| B2619: BCM |
Inhibit setting the vehicle to READY |
1 second after the steering lock unit power supply output control inside BCM becomes normal |
| B261E: VEHICLE TYPE |
- Inhibit setting the vehicle to READY
- Inhibit steering lock
|
When HPCM status signal (CAN) is received normally from HPCM |
| B26EF: STRG LCK RELAY OFF |
Inhibit setting the vehicle to READY |
When the following conditions are fulfilled
- Steering lock relay signal (CAN): ON
- Steering lock unit status signal (CAN): ON
|
| B26F0: STRG LCK RELAY ON |
Inhibit setting the vehicle to READY |
When the following conditions are fulfilled
- Steering lock relay signal (CAN): OFF
- Steering lock unit status signal (CAN): OFF
|
| B26F1: IGN RELAY OFF |
Inhibit setting the vehicle to READY |
When the following conditions are fulfilled
- Ignition switch ON signal (CAN: Transmitted from BCM): ON
- Ignition switch ON signal (CAN: Transmitted from IPDM E/R): ON
|
| B26F2: IGN RELAY ON |
Inhibit setting the vehicle to READY |
When the following conditions are fulfilled
- Ignition switch ON signal (CAN: Transmitted from BCM): OFF
- Ignition switch ON signal (CAN: Transmitted from IPDM E/R): OFF
|
| B26F7: BCM |
Inhibit setting the vehicle to READY by Intelligent Key system |
When room antenna and luggage room antenna functions normally |
| U0415: VEHICLE SPEED |
Inhibit steering lock |
When vehicle speed signal (Meter) (CAN) is received normally |