LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2013 >> FX50 >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System - DTCS P0137 Through P0456 >> DTC P0340, P0345: CMP Sensor >> Diagnosis Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnosis Procedure

  1. CHECK STARTING SYSTEM 

    Turn ignition switch to START position.

    Does the engine turn over? Does the starter motor operate? 

    YES: GO TO 2.

    NO: Check starting system. (Refer to "DIAGNOSIS AND REPAIR WORK FLOW ".)

  2. CHECK GROUND CONNECTION 
    1. Turn ignition switch OFF.
    2. Check ground connections M95. Refer to Ground Inspection in "CIRCUIT INSPECTION ".

      Is the inspection result normal? 

      YES: GO TO 3.

      NO: Repair or replace ground connection.

  3. CHECK CAMSHAFT POSITION SENSOR POWER SUPPLY CIRCUIT-I 
    1. Disconnect camshaft position (CMP) sensor harness connector.
    2. Turn ignition switch ON.
    3. Check the voltage between CMP sensor harness connector and ground.
      DTC CMP sensor Ground Voltage (V)
      Bank Connector Terminal
      P0340 1 F84 1 Ground Approx. 5
      P0345 2 F83 1

      Is the inspection result normal? 

      YES: GO TO  9.

      NO-1: P0340: GO TO 4.

      NO-2: P0345: Repair open circuit, short to ground or short to power in harness or connectors.

  4. CHECK CMP SENSOR POWER SUPPLY CIRCUIT-II 
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check the continuity between CMP sensor harness connector and ECM harness connector.
      CMP sensor ECM Continuity
      Bank Connector Terminal Connector Terminal
      1 F84 1 F111 91 Existed

      Is the inspection result normal? 

      YES: GO TO 5.

      NO: Repair open circuit.

  5. CHECK SENSOR POWER SUPPLY CIRCUIT 

    Check harness for short to power and short to ground, between the following terminals.

    ECM Sensor
    Connector Terminal Name Connector Terminal
    F111 87 Crankshaft position sensor F2 1
    91 CMP sensor (bank 1) F84 1
    EVT control position sensor (bank 1) F59 1
    95 Battery current sensor E21 1
    EVAP control system pressure sensor(1) B252 3
    Manifold absolute pressure sensor F65 1
    M160 99 APP sensor 2 (Without ICC) E112 6
    APP sensor 2 (With ICC) E116 3
    (1) Except for Mexico

    Is the inspection result normal? 

    YES: GO TO 6.

    NO: Repair short to ground or short to power in harness or connectors.

  6. CHECK COMPONENTS 

    Check the following.

  7. CHECK APP SENSOR 

    Refer to "COMPONENT INSPECTION ".

    Is the inspection result normal? 

    YES: GO TO  13.

    NO: GO TO 8.

  8. REPLACE ACCELERATOR PEDAL ASSEMBLY 
    1. Replace accelerator pedal assembly.
    2. Perform "SPECIAL REPAIR REQUIREMENT ".

      : INSPECTION END

  9. CHECK CMP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT 
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check the continuity between CMP sensor harness connector and ECM harness connector.
      DTC CMP sensor ECM Continuity
      Bank Connector Terminal Connector Terminal
      P0340 1 F84 2 F111 58 Existed
      P0345 2 F83 2 62
    4. Also check harness for short to ground and short to power.

      Is the inspection result normal? 

      YES: GO TO 10.

      NO: Repair open circuit, short to ground or short to power in harness or connectors.

  10. CHECK CMP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT 
    1. Check the continuity between CMP sensor harness connector and ECM harness connector.
      DTC CMP sensor ECM Continuity
      Bank Connector Terminal Connector Terminal
      P0340 1 F84 3 F111 59 Existed
      P0345 2 F83 3 63
    2. Also check harness for short to ground and short to power.

      Is the inspection result normal? 

      YES: GO TO 11.

      NO: Repair open circuit, short to ground or short to power in harness or connectors.

  11. CHECK CAMSHAFT POSITION SENSOR 

    Refer to "COMPONENT INSPECTION ".

    Is the inspection result normal? 

    YES: GO TO 12.

    NO: Replace malfunctioning camshaft position sensor. Refer to "EXPLODED VIEW ".

  12. CHECK CAMSHAFT (INT) 

    Check the following.

    • Accumulation of debris to the signal plate of camshaft front end
    • Chipping signal plate of camshaft front end

      Is the inspection result normal? 

      YES: GO TO 13.

      NO: Remove debris and clean the signal plate of camshaft front end or replace camshaft. Refer to "EXPLODED VIEW ".

      Fig 1: Inspecting Camshaft Signal Plate
      G09001443Courtesy of NISSAN NORTH AMERICA, INC.
  13. CHECK INTERMITTENT INCIDENT 

    Refer to "INTERMITTENT INCIDENT ".

    : INSPECTION END

scientia non olet · About LEMON Manuals