Diagnostic Trouble Code Index DTC: Transfer Case Control Module (TCCM) -- F-Type/X152

• Diagnostic Trouble Code (DTC) Index DTC: Transfer Case Control Module (TCCM)
  • Description And Operation
    • Transfer Case Control Module (TCCM)
      • Notes
      • B1142-62: Ignition Status 1 - Signal compare failure
        • Possible Causes
        • Action
      • P080A-56: Clutch Position Not Learned - Invalid/incomplete configuration
        • Possible Causes
        • Action
      • P0810-04: Clutch Position Control Error - System internal failures
        • Possible Causes
        • Action
      • P0810-07: Clutch Position Control Error - Mechanical failures
        • Possible Causes
        • Action
      • P0810-56: Clutch Position Control Error - Invalid/incomplete configuration
        • Possible Causes
        • Action
      • P0810-78: Clutch Position Control Error - Alignment or adjustment incorrect
        • Possible Causes
        • Action
      • P170E-92: Clutch Delivered Torque Performance - Performance or incorrect operation
        • Possible Causes
        • Action
      • P173A-64: Clutch Actuator Position Sensor Circuit Range/Performance - Signal plausibility failure
        • Possible Causes
        • Action
      • P175B-00: Transfer Case Clutch Deteriorated - No sub type information
        • Possible Causes
        • Action
      • P175C-00: Transfer Case Fluid Deteriorated - No sub type information
        • Possible Causes
        • Action
      • P215A-62: Vehicle Speed/Wheel Speed Correlation - Signal compare failure
        • Possible Causes
        • Action
      • P2787-98: Clutch Temperature Too High - Component or system over temperature
        • Possible Causes
        • Action
      • U0001-81: High Speed CAN Communication Bus - Invalid serial data received
        • Possible Causes
        • Action
      • U0001-82: High Speed CAN Communication Bus - Alive/sequence counter incorrect/not updated
        • Possible Causes
        • Action
      • U0001-83: High Speed CAN Communication Bus - Value of signal protection calculation incorrect
        • Possible Causes
        • Action
      • U0001-87: High Speed CAN Communication Bus - Missing message
        • Possible Causes
        • Action
      • U0001-88: High Speed CAN Communication Bus - Bus off
        • Possible Causes
        • Action
      • U0300-00: Internal Control Module Software Incompatibility - No sub type information
        • Possible Causes
        • Action
      • U2012-4A: Car Configuration Parameter(s) - Incorrect component installed
        • Possible Causes
        • Action
      • U2100-54: Initial Configuration Not Complete - Missing calibration
        • Possible Causes
        • Action
      • U3000-47: Control Module - Watchdog/safety microcontroller failure
        • Possible Causes
        • Action
      • U3000-49: Control Module - Internal electronic failure
        • Possible Causes
        • Action
      • U3000-4B: Control Module - Over temperature
        • Possible Causes
        • Action
      • U3006-13: Control Module Input Power A - Circuit open
        • Possible Causes
        • Action
      • U3006-16: Control Module Input Power A - Circuit voltage below threshold
        • Possible Causes
        • Action
      • U3006-17: Control Module Input Power A - Circuit voltage above threshold
        • Possible Causes
        • Action
      • U3006-62: Control Module Input Power A - Signal compare failure
        • Possible Causes
        • Action
      • U3007-13: Control Module Input Power B - Circuit open
        • Possible Causes
        • Action
      • U3007-16: Control Module Input Power B - Circuit voltage below threshold
        • Possible Causes
        • Action
      • U3007-17: Control Module Input Power B - Circuit voltage above threshold
        • Possible Causes
        • Action
      • U3007-62: Control Module Input Power B - Signal compare failure
        • Possible Causes
        • Action