LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Jeep >> 2000 >> Cherokee Classic, 2D Pickup >> Repair and Diagnosis >> Body & Frame >> Body, Cab Control Systems >> Body Control Modules >> System Tests >> Power Door Locks/Remote Keyless Entry System >> Remote Keyless Entry Inoperative
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Remote Keyless Entry Inoperative

  1. Operate power door locks from door switches. If door locks operate correctly, go to next step. If door locks do not operate correctly, go to appropriate POWER DOOR LOCKS & REMOTE KEYLESS ENTRY SYSTEMS article.
  2. Using scan tool, select THEFT ALARM, MISCELLANEOUS, then PROGRAM RKE. Follow scan tool instructions and program all transmitters to be used with vehicle. Operate door locks using transmitter. If door locks do not operate properly, go to next step. If door locks operate properly, test is complete.
  3. Remove RKE transmitter batteries. Using DVOM, measure voltage of batteries. If voltage is greater than 3 volts, go to next step. If voltage is less than 3 volts, replace batteries. Perform BODY VERIFICATION TEST  under VERIFICATION TESTS.
  4. Using scan tool, program transmitter. Follow scan tool instructions. Using RKE transmitter, operate door locks. If door locks do not operate correctly, go to next step. If door locks operate correctly, test is complete.
  5. Disconnect RKE module connector. RKE module is mounted in roof or overhead console. See COMPONENT LOCATIONS  . Using a DVOM, measure voltage between ground and RKE module connector terminal No. 2 (Pink wire). See Figure . If voltage is 10 volts or greater, go to next step. If voltage is less than 10 volts, repair open in Pink wire between power distribution center and RKE module. Perform BODY VERIFICATION TEST  under VERIFICATION TESTS.
  6. Connect a jumper wire between ground and RKE module connector terminal No. 5 (Dark Blue wire). If door lock motor operates, disconnect jumper wire and go to next step. If door lock motor does not operate, go to step  9 .
  7. Connect a jumper wire between ground and RKE module connector terminal No. 11 (Light Blue/Red wire). If door lock motor does not operate, go to next step. If door lock motor operates, replace RKE module. See OVERHEAD CONSOLE  under REMOVAL & INSTALLATION. Perform BODY VERIFICATION TEST  under VERIFICATION TESTS.
  8. Remove passenger door panel. Disconnect passenger door module 8-pin harness connector. Connect a jumper wire between ground and RKE module connector terminals No. 5 (Dark Blue wire) and No. 11 (Light Blue/Red wire). Using DVOM, measure resistance between ground and passenger door module 8-pin connector terminal No. 2 (Dark Blue/Pink wire). See Figure . If resistance is less than 5 ohms, go to step  11 . If resistance is 5 ohms or greater, repair open in Dark Blue/Pink or Dark Blue wire between RKE module and passenger door module. Perform BODY VERIFICATION TEST  under VERIFICATION TESTS.
  9. Remove passenger door panel. Disconnect passenger door module 8-pin connector. Connect a jumper wire between ground and RKE module connector terminals No. 5 (Dark Blue wire) and No. 11 (Light Blue/Red wire). Using DVOM, measure resistance between ground and passenger door module 8-pin connector terminal No. 2 (Dark Blue/Pink wire). See Figure . If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or greater, repair open in Dark Blue/Pink or Dark Blue wire between RKE module and passenger door module. Perform BODY VERIFICATION TEST  under VERIFICATION TESTS.
  10. Reconnect passenger door module 8-pin connector. Connect a jumper wire between ground and RKE module connector terminal No. 11 (Light Blue/Red wire). If door lock motor does not operate, go to next step. If door lock motor operates, replace RKE module. See OVERHEAD CONSOLE  under REMOVAL & INSTALLATION. Perform BODY VERIFICATION TEST  under VERIFICATION TESTS.
  11. Disconnect passenger door module 8-pin connector. Connect a jumper wire between ground and RKE module connector terminals No. 5 (Dark Blue wire) and No. 11 (Light Blue/Red wire). Using DVOM, measure resistance between ground and passenger door module 8-pin connector terminal No. 1 (Light Blue/Red wire). If resistance is less than 5 ohms, replace passenger door module. Perform BODY VERIFICATION TEST  under VERIFICATION TESTS. If resistance is 5 ohms or greater, repair open in Light Blue/Red wire between RKE module and passenger door module. Perform BODY VERIFICATION TEST  under VERIFICATION TESTS.
scientia non olet · About LEMON Manuals