Electronic Control Modules (Service Information)

• Electronic Control Modules - Service Information
  • Standard Procedure
    • SKREEM Programming
      • Notes
      • Programming The SKREEM
      • ECM/Skim/WCM Programming
        • Notes
        • Programming The Skim
        • Programming Ignition Keys To The SKREEM
  • Communication
    • Description
      • Can-Lin Bus
    • Operation
      • Can-Lin Bus
  • Data Link Connector
    • Description
      • Data Link Connector
    • Operation
      • Data Link Connector
  • Module-All Wheel Drive Control
    • Description
      • All Wheel Drive Control Module
    • Operation
      • All Wheel Drive Control Module
    • Removal
      • Final Drive Control Module
    • Installation
      • Final Drive Control Module
  • Module-Antilock Brake
    • Description
      • Module-Antilock Brake
    • Operation
      • Module-Antilock Brake
    • Removal
      • Module-Antilock Brake
    • Installation
      • Module-Antilock Brake
  • Engine Control Module
    • Description
      • Engine Control Module (ECM)
    • Operation
      • Engine Control Module (ECM)
        • Notes
        • ECM Operating Modes
        • Ignition Switch On (Engine Off)
        • Engine Start-Up Mode
        • Normal Driving Modes
        • Limp-In Mode
        • Overspeed Detection Mode
        • After-Run Mode
        • Monitored Circuits
        • Diagnostic Trouble Codes
        • Hard Code
        • Intermittent Code
        • ECM Diagnostic Trouble Codes
    • Standard Procedure
      • Pcm/ECM Programming - Diesel
        • Pcm/TCM Flash Reprogramming
        • Table Of Contents
        • Section 1 - Pcm/TCM Flash Procedure
        • REPAIR PROCEDURE - Using StarSCAN® or StarMOBILE® Desktop Client
        • REPAIR PROCEDURE - Using StarMOBILE® Standalone Diagnostic Mode
        • Section 2 - Additional Pcm/TCM Replacement Procedures
        • Step-By-Step Instructions
        • Section 3 - Authorized Modification Label
        • Required Tools/Equipment:
        • TECH TIPS and INFORMATION:
        • Parts Required
    • Removal
      • Engine Control Module (ECM)
    • Installation
      • Engine Control Module (ECM)
  • Module-Heated Seat
    • Description
      • Module, Heated Seat
    • Operation
      • Module, Heated Seat
    • Diagnosis And Testing
      • Heated Seat Module
    • Removal
      • Heated Seat Module
    • Installation
      • Heated Seat Module
  • Module-Powertrain Control
    • Description
      • Pcm Ground
      • Sensor Return - Pcm Input
    • Operation
      • 5 Volt Supply - Pcm Output
      • Powertrain Control Module
    • Standard Procedure
      • Obtaining Diagnostic Trouble Codes
        • Bulb Check
        • Obtaining DTC'S Using Scan Tool
      • Pcm/ECM Programming - Gas
        • Pcm / TCM Flash Reprogramming
        • Table Of Contents
        • Section 1 - Pcm / TCM Flash Procedure
        • REPAIR PROCEDURE - Using StarSCAN® or StarMOBILE® Desktop Client
        • REPAIR PROCEDURE - Using StarMOBILE® Standalone Diagnostic Mode
        • Section 2 - Additional Pcm / TCM Replacement Procedures
        • Step-By-Step Instructions
        • Section 3 - Authorized Modification Label
        • Required Tools/Equipment:
        • TECH TIPS and INFORMATION:
        • Parts Required
      • Pinion Factor Setting
    • Removal
      • Module - Powertrain Control
    • Installation
      • Module - Powertrain Control
  • Module-Steering Control
    • Description
      • Steering Control Module
    • Operation
      • Steering Control Module
    • Diagnosis And Testing
      • Steering Control Module
  • Module-Transmission Control
    • Description
      • Transmission Control Module
    • Operation
      • Transmission Control Module
        • Shift Control
        • "Drive" Position
        • When using the Manual Mode (Vehicles with the manual mode)
        • Downhill Engine Brake Control
        • Acceleration Control
        • Line Pressure and Secondary Pressure Control
        • Normal Fluid Pressure Control
        • Secondary Pressure Feedback Control
        • Lock-up Control
        • Selection Control
        • CAN Communication
        • Inputs and Outputs
        • Engine/CVT Integration Control (CAN Communication Control)
        • Fail-safe Function
        • Secondary Speed Sensor
        • Primary Speed Sensor
        • PNP Switch
        • Fluid Temperature Sensor
        • Secondary Pressure Sensor
        • Line Pressure Solenoid
        • Secondary Pressure Solenoid
        • Lock-up solenoid
        • Stepping Motor
        • Lock-up/Selection Switching Solenoid
        • Backup Power Supply
        • TCM
        • Primary Speed Sensor, Secondary Speed Sensor
    • Standard Procedure
      • Transmission Control Module
        • Notes
        • Initial Learn (Brand-New Module, Memory Already Clear)
        • Relearn, After Replacing A Transaxle
    • Removal
      • Transmission Control Module
    • Installation
      • Transmission Control Module