Standard Procedure: EMEA

Time Allowance:
Details:
DEALERSHIP IDENTIFICATION DATA
Company Name
Sincom Code
VEHICLE IDENTIFICATION DATA
Model
Version
Chassis No.

A - VEHICLE READINESS NOTE: Note: This document is for reference purposes only. The instructions are not VIN-specific, and it is not required to print or retain this document for each New Vehicle Prep performed.
#	Description	Action	OK
1	Do not remove protective transit film from body of vehicle and keep all wheel covers on vehicle until sold or up to 180 days	Do not remove protective transit film from body of vehicle and keep all wheel covers on vehicle until sold or up to 180 days.	?
2	Place vehicle into Customer Mode (all others)	Using wiTECH, place the vehicle into Customer Mode by following the Exit Logistics Mode within the Vehicle Prep tab or using the manual procedure below: Turn the ignition key on (no engine cranking or running requested) Turn on the hazard lamp (a/k/a/ emergency flashers) Press the "Up Arrow" button on the steering wheel and hold for 5 second Mode is switched from "Shipping Mode" to "Customer Mode" - the EVIC display will update Turn off the hazard lamp	?
3	Inflate tire pressure to max side wall pressure (except Viper)	Increase the tire pressure to maximum sidewall pressure if vehicle is going into lot storage.	?
4	Fit all components which were sent separately	Fit all components which were sent separately	?
5	Install the front number plate holder (if needed)	Install the front number plate holder (if needed)	?
6	Install the roof rack	Install the roof rack	?
7	Install the aerial	Install the aerial	?

B - UNDER THE BONNET
#	Description	Action	OK
8	Bonnet latch and safety catch - adjust as needed	Verify the operation of the bonnet release system including the inside bonnet release lever and the outside hood secondary safety catch. Adjust if necessary. The safety catch prevents the bonnet from going to the full open position until it is manually released. To test the safety catch, unlatch the bonnet with the interior bonnet release lever and attempt to raise the bonnet without operating the safety catch.	?
9	Battery State-of-Charge - document voltage	Check the battery state of charge by connecting a digital voltmeter at the jump-start locations. The battery voltage should be at least 12.4 volts (Fiat 500 BEV/Pacifica PHEV -100%). If charging is necessary, follow the service information procedures and recharge the battery. Record voltage on New Vehicle Prep (NVP) form.	?
9	Battery State-of-Charge - document voltage	For international EMEA market vehicles, print the primary battery and/or the ESS auxiliary battery (If equipped) status check result ticket and archive it together with the New Vehicle Prep Check Sheet. Refer to Service Bulletin 08-073-17.	?
10	Loose Attachments, Routing and Clearance	Check routing, connectors, connections and clearance of: brake lines fuel lines power steering lines intake system flexible lines clutch lines coolant lines electric wiring drive belts	?
11	All Fluid Levels	Refer to the Owner Handbook or service information for proper fluid level inspection locations.	?
12	No Fluid Leaks present	Visually inspect the area under the bonnet to make sure that there are no fluid leaks. Check clamps for tightness and full engagement	?

C - LOWER VEHICLE PART
#	Description	Action	OK
13	No Fluid Leaks present	Raise the vehicle on an appropriate hoist and check the following: Loose Attachments, Routing Clearance and Damage, Absence of Fluid Leaks. Refer to the appropriate Service Information for proper lift points. Check clamps for tightness and full engagement.	?
14	Loose Attachments, Routing, Clearance, Damage	Raise the vehicle on an appropriate hoist and check the following: Loose Attachments, Routing Clearance and Damage, Absence of Fluid Leaks. Refer to the appropriate Service Information for proper lift points. Check clamps for tightness and full engagement.	?

D - ROAD TEST
#	Description	Action	OK
15	Carry out the road test. Distance: Before _______________ After _______________	Record the distance before and after the road test.	?
16	Engine Starts with All Keys	Start vehicle with all sets of keys.	?
17	All Warning Lights and Gauges / No DTCs	Verify all warning lights and gauges are operating properly, and no fault codes exist.	?
18	Keyless Go	Ensure vehicle starts with push button, when key is inside vehicle.	?
19	Engine Starts Only in Park & Neutral	Verify engine will only start while automatic transmission is in park or neutral.	?
20	Service and parking brakes	Apply the service brakes while the vehicle is in motion. Be sure the brake operation is smooth and positive. Make sure the vehicle stops in a straight line and without pulling to one side. Ensure there is no shudder or vibration when braking. Ensure that the parking brake is easy to operate. Make sure the parking brake does not drag.	?
21	Transmission/brake synchronizer	On versions with automatic transmission, make sure that the vehicle only starts when the brake pedal is pressed.	?
22	Control with automatic transmission	Make sure that the park lock mechanism holds the vehicle. With the vehicle on a grade, put the automatic transmission in park and slowly release the service brake to check the operation of the park mechanism. Make sure the shift lever operates easily and smoothly. Check for smooth shifting. Check for proper upshifting and downshifting.	?
23	Engine Performance - Cold	The engine must: start correctly idle smoothly and at proper speed be free from stumbling or hesitation produce sufficient power be free of unusual noises operate within the proper temperature range and stop when the ignition key is shut off or stop button is pressed.	?
24	Engine Performance - Hot	The engine must: start correctly idle smoothly and at proper speed be free from stumbling or hesitation produce sufficient power be free of unusual noises operate within the proper temperature range and stop when the ignition key is shut off or stop button is pressed.	?
25	Steering and Handling	Check that the power assist works properly. Make sure that the steering wheel does not vibrate abnormally at idle or road speed. Ensure that the steering wheel is centered when traveling in a straight line. Check that the vehicle does not drift to either side on flat road surfaces. Make sure that the vehicle does not vibrate or shake abnormally.	?
26	Noise, Vibration, Squeaks, or Rattles	Check that the vehicle is free of noise, vibrations, squeaks, or rattles. Tighten any loose fasteners.	?
27	Heater / Defrost- Front	Check the heater operation after the vehicle has reached operating temperature. Operate blower motor at all speeds. Operate the system in all modes. Check for hot air at all appropriate outlets. Check for temperature control operation.	?
28	A/C	Make sure that the A/C system is cooling appropriately. Operate blower motor at all speeds. Check cool air flow from all vents. Operate the system in all modes.	?
29	Rear heater and A/C (where fitted)	Check correct operation of rear heater and A/C system.	?
30	Defrost - Rear	Make sure that the rear defroster with electric heater works correctly. Switch on all check heating.	?
31	Blind spot monitoring system (where fitted)	During a road test, check that the visual indicators on the side mirrors appear correctly when an object is present in the detection zone.	?
32	Cruise Control (where fitted)	Check the "on/off" switch. Check the "set" operation. Check the "resume" function. Check the "accelerate" and "decelerate" function. Check the "cancel" button. Check the brake/clutch release function. If equipped, verify operation of Adaptive Cruise Control function.	?
33	Set the compact variance/calculation (where fitted)	Refer to the service information on TechCONNECT for information regarding compass setting procedures.	?
34	Tire pressure monitoring system (where fitted)	Verify that tire pressure monitoring system warning light is not illuminated when tires are above minimum inflation recommendations. Ensure that warning light is not flashing.	?
35	Transfer Case (where fitted)	Shift the transfer case through all ranges to make sure all shifting is smooth and operates properly.	?
36	Load levelling air suspension (where fitted)	Use the Selec-Terrain switch to adjust the ground clearance in normal driving conditions. Switch to all selections and check that the air suspension system works correctly.	?
37	Parking Assist (where fitted)	Put vehicle in reverse and slowly back up toward an object. Verify that Park Assist warning icon, lights and chimes operate properly as object is approached.	?
38	Back-Up Camera (where fitted)	Put vehicle in reverse, verify that screen provides a clear and visible image from rear of vehicle.	?

E - INTERIOR
#	Description	Action	OK
39	Visually Inspect Interior Parts for Damage, Fit, etc.	From the interior of the vehicle, open and close all doors to ensure ease of operation. Fully open and close the glove box to ensure proper operation. Fully open and close the console door to ensure proper operation. Check interior panels for proper fit and free from damage.	?
40	All interior lights and horn	Operate switches and interior lights, visually inspecting them, including ceiling/reading lights, and (where fitted): vanity mirror light storage compartment lights ashtray light cigar lighter light radio lights door lights and illuminated entrance system Ensure that the horn operates properly.	?
41	Rear View Mirror	Check that the rearview mirror's day/night function Is operating properly.	?
42	Front and rear washers and wipers	Operate the windscreen wipers and, where fitted, the rear wipers and check correct operation at all speeds. Operate the windscreen wipers and where fitted, the rear wipers. Check correct operation and spray pattern. Check correct operation of the wiper flick function.	?
43	All interior door locks including child locks	Check all interior door locks for proper operation, including rear child safety door locks if equipped. Place in the unlocked position.	?
44	Steering Wheel Mounted Controls	Check all steering wheel controls for proper operation.	?
45	Memory mirror/seat (where fitted)	Check correct operation of the memory mirror and seat systems.	?
46	Cigar lighter (where fitted)	Check cigar lighter for proper operation.	?
47	Power windows and window lock switch	Fully open and close all power windows to ensure proper operation and sealing. Ensure that the windows operate properly at each door. Verify that window lock button is operating properly. Verify the operation of the "One Touch Up/Down" feature if equipped.	?
48	Outside Power Mirrors	Check power mirrors for proper operation.	?
49	Heated mirrors (where fitted)	Check correct operation of the heated electric mirrors.	?
50	Glove Box	Check into the glove box if available informative material like (leaflet, TipCard or similar) to be place on the internal mirror. If yes please proceed (see photo below for leaflet)
51	Seats and Seat Belts - All Adjustments	Check for correct installation and operation of seat and shoulder belts, and retractors. Check that the restraint system safety labels regarding the use of seatbelts and airbags are in place. Fully cycle the seats for proper adjustments and verify that each seat is securely mounted. Fold down and latch the rear seats. Pull forward to check that the latches operate correctly. Check for proper head restraint operation.	?
52	Sunroof (where fitted)	Run a complete sunroof opening/closing cycle. Make sure that the sunroof opens and closes easily. Check correct operation of the opening/closing function by pressing the button once (where fitted).	?
53	Clock setting	Clock setting	?
54	Sound system	Switch on the radio and check reception on AM and FM frequencies. Check that the CD player is working correctly. Check that the audio quality is high from all speakers.	?
55	Satellite radio (where fitted)	Switch on the satellite radio and check reception.	?
56	Deactivate the front seat video system (where fitted for CT, FL, OK, WV)	Use the scan tool to deactivate the front seat video when the vehicle is not in Park position.	?
57	Video system (where fitted)	Test the DVD player to make sure that the DVD is loaded correctly and appears on the screen.	?
58	Wireless headset/vehicle remote control (where fitted)	Check correct operation of the wireless headset/video remote control.	?
59	Heated steering wheel (where fitted)	Restore the correct operation of the heated steering wheel.	?
60	Power socket	Check correct operation of all power sockets.	?
61	Integrated child restraint system/seat belt	Check correct operation of the child restraint system/seat belt systems.	?
62	Containers positioned correctly around the spare wheel	Check that the containers are positioned correctly.	?
63	Heated seats (where fitted)	Check for proper operation of ventilated seats on all power levels, on all equipped seats.	?
64	Electric cooled seats (where present)	Check correct operation of ventilated seats at all power levels, on all the concerned seats.	?
65	Luggage compartment cover (where fitted)	Check correct operation of the rear luggage compartment cover.	?

Courtesy of CHRYSLER GROUP, LLC

F - EXTERIOR
#	Description	Action	OK
66	Inspect Body and Paint for Damage and Fit/ Finish	Inspect the body exterior for damage, loose or missing items. During the inspection, ensure that no vehicle damage occurred from the time the vehicle was received and the beginning of the New Vehicle Preparation. NOTE: DO NOT POLISH, WAX, AND/OR TOUCH UP MATTE PAINT.	?
67	Exterior Lamps - Headlamps, Turn Signals, Hazards, Park/Tail/License Plate, Trunk Lights, etc.	Actuated and visually check for the following: headlights (main beam/dipped beam) direction indicators hazard warning lights parking/rear/number plate lights reversing lights fog lights brake lights (including central light) daytime running lights (where fitted) side markers load bed lights and other lights	?
68	Doors, tailgate - Adjust strikers, if needed	Open all doors/tailgate from the outside to check operation of exterior handles. Check door stay. Partially close all doors to check the open door stay. Close all doors/tailgate to check operation of locks and strikers. Adjust the strikers, if needed. Check each of use of the tailgate.	?
69	Electric tailgate - Check correct assembly and operation (where fitted)	Check all operating modes of the electric tailgate, including operation of the tailgate using interior switches and Remote Keyless Entry transmitter.	?
70	Electric sliding door - Check correct assembly and operation (where fitted)	Check all operating modes of the electric sliding door, including its operation using interior switches and Remote Keyless Entry transmitter.	?
71	Safety alarm test (where fitted)	Lock all doors using the Remote Keyless Entry transmitter. Check operation of the vehicle safety system warning light.	?
72	Passive Entry (where fitted)	Check operation of the Keyless Enter-N-Go system. With the door lock engaged and the Remote Keyless Entry transmitter placed at a distance of 1.5 m from the vehicle, check that the doors open. The door must open automatically.	?
73	Remote Keyless Entry (where fitted)	Check that the doors are unlocked correct using all the keys with remote control.	?
74	Remote start (where fitted)	Check that the engine starts with all keys using the Remote Keyless Entry transmitter.	?
75	Lock and unlock all doors using the mechanical keys	Check that the mechanical keys lock and unlock all doors.	?

G - VEHICLE STORAGE
#	Description	Action	OK
76	Keep all protective transit film on body of vehicle and keep all wheel covers on the vehicle until it is sold	Keep all protective transit film on body of vehicle and keep all wheel covers	?
77	Inflate the tires to maximum pressure	Inflate the tires to maximum pressure (except for heavy trucks).	?
78	Remove the fuse to reduce electric load (IOD)	Remove the fuse before depositing the vehicle to preserve the battery.	?
79	Set the vehicle to Ship Mode	Turn the ignition key on (No engine cranking or running required). Turn on the hazard lamp (a/k/a/ emergency flashers). Press the "Up Arrow" button on the steering wheel and hold for 5 seconds. Mode is switched from "Customer Mode" to "Shipping Mode" - the EVIC display will update. Turn off the hazard lamps.	?

H - FINAL DETAIL & INSPECTION
#	Description	Action	OK
80	Perform all incomplete recalls and RRTs (Print a current VIP Report)	Perform all incomplete recalls and RRTs (Print a current VIP Report).	?
81	Set the vehicle to Customer Mode	Turn the ignition key on (No engine cranking or running required). Turn on the hazard lamp (a/k/a/ emergency flashers). Press the "Up Arrow" button on the steering wheel and hold for 5 seconds. Mode is switched from "Shipping Mode" to "Customer Mode" - the EVIC display will update. Turn off the hazard lamps.	?
82	Do not remove protective transit film from body of vehicle and keep all wheel covers on vehicle until sold	Remove exterior protective coatings/coverings from vehicle, remove interior protective covers, grease markings on door jambs, unnecessary labels, etc.	?
83	Check paintwork and bodywork and touch up, if needed.	Make sure there are not paint marks or scratches on the bodywork. Correct marks/scratches using thin coats of paint. Make sure there are no paint marks or scratches on the bodywork.	?
84	Check and adjust the battery charge.	Check the battery charge using a digital voltmeter.	?
85	Adjust tire pressure, including spare tire, to the values shown on door placard	Adjust tire pressure, including spare tire, to the values shown on door placard	?
86	Top up the diesel emissions additive tank	Fill the diesel emission additive tank behind the passenger compartment, in the boot on driver's side (clearly indicated in blue) with Mopar diesel emissions additive before delivery to the customer.	?
87	Wash and clean the outside of the vehicle.	Wash the vehicle completely. Clean the external part of the tires and of the wheel covers (using non-acid wheel detergents). Clean the windows on the outside and inside.	?
88	Clean the vehicle interior.	Check interior trim, seats, upholstery and molding. Clean, if needed.	?