LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Kia >> 2015 >> Sedona EX >> Repair and Diagnosis >> Engine Performance >> Tune-Up >> Ignition System >> Spark Plug >> Repair Procedures >> Removal
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Repair Procedures: Removal

NOTE:
  • Be careful that no contaminant enters into spark plug holes.
  • Use the spark plug wrench (A) to prevent the damage on the spark plug.
Fig 1: Removing Spark Plug
G10648685Courtesy of KIA MOTORS AMERICA, INC.
NOTE:
  • When removing the ignition coil connector, pull the lock pin (A) and push the clip (B).
Fig 2: Pulling Lock Pin
G10648686Courtesy of KIA MOTORS AMERICA, INC.

Ignition coil (Cylinder #1) [Bank 1] 

  1. Remove the surge tank.

    (Refer to Engine Mechanical System - "SURGE TANK ")

  2. Disconnect the Ignition coil connector (A).
  3. Remove the ignition coil after loosening the mounting bolt (B).
    Fig 3: Ignition Coil Connector
    G10648687Courtesy of KIA MOTORS AMERICA, INC.
  4. Remove the spark plug.

Ignition coil (Cylinder #2) [Bank 2] 

  1. Turn the ignition switch off and disconnect the battery negative (-) Terminal.
  2. Disconnect the Ignition coil connector (A).
  3. Remove the ignition coil after loosening the mounting bolt (B).
    Fig 4: Ignition Coil Mounting Bolt
    G10648688Courtesy of KIA MOTORS AMERICA, INC.
  4. Remove the spark plug.

Ignition coil (Cylinder #3) [Bank 1] 

  1. Remove the surge tank.

    (Refer to Engine Mechanical System - "SURGE TANK ")

  2. Disconnect the Ignition coil connector (A).
  3. Remove the ignition coil after loosening the mounting bolt (B).
    Fig 5: Ignition Coil Connector
    G10648689Courtesy of KIA MOTORS AMERICA, INC.
  4. Remove the spark plug.

Ignition coil (Cylinder #4) [Bank 2] 

  1. Turn the ignition switch off and disconnect the battery negative (-) Terminal.
  2. Disconnect the Ignition coil connector (A).
  3. Remove the ignition coil after loosening the mounting bolt (B).
    Fig 6: Ignition Coil Mounting Bolt
    G10648690Courtesy of KIA MOTORS AMERICA, INC.
  4. Remove the spark plug.

Ignition coil (Cylinder #5) [Bank 1] 

  1. Remove the surge tank.

    (Refer to Engine Mechanical System - "SURGE TANK ")

  2. Disconnect the Ignition coil connector (A).
  3. Remove the ignition coil after loosening the mounting bolt (B).
    Fig 7: Ignition Coil Connector
    G10648691Courtesy of KIA MOTORS AMERICA, INC.
  4. Remove the spark plug.

Ignition coil (Cylinder #6) [Bank 2] 

  1. Turn the ignition switch off and disconnect the battery negative (-) terminal.
  2. Disconnect the Ignition coil connector (A).
  3. Remove the ignition coil after loosening the mounting bolt (B).
    Fig 8: Ignition Coil Mounting Bolt
    G10648692Courtesy of KIA MOTORS AMERICA, INC.
  4. Remove the spark plug.

Installation 

  1. Install in the reverse order of removal.

    Spark Plug Installation 

    14.7 ~ 24.5 N.m (1.5 ~ 2.5 kgf.m, 10.8 ~ 18.0 lb-ft)

scientia non olet · About LEMON Manuals