Connector [C100-B]
| Pin No. | Description | Condition | Type | Level |
|---|---|---|---|---|
| 1 | ECM ground | Idle | DC | -0.3 ~ 0.5V |
| 2 | ECM ground | Idle | DC | -0.3 ~ 0.5V |
| 3 | Battery power (B+) | IG OFF | DC | Max. 1.0V |
| IG ON | Battery voltage (B+) | |||
| 4 | ECM ground | Idle | DC | -0.3 ~ 0.5V |
| 5 | Battery power (B+) | IG OFF | DC | Max. 1.0V |
| IG ON | Battery voltage (B+) | |||
| 6 | Battery power (B+) | IG OFF | DC | Max. 1.0V |
| IG ON | Battery voltage (B+) | |||
| 7 | - | |||
| 8 | FlexRay communication [High] signal input | |||
| 9 | - | |||
| 10 | Brake switch [Test] signal input | Brake OFF | DC | Battery voltage (B+) |
| Brake ON | Max. 0.5V | |||
| 11 | - | |||
| 12 | - | |||
| 13 | Electric load signal input | Lamp OFF | DC | Battery voltage (B+) |
| Lamp ON | -0.3 ~ 0.5V | |||
| 14 | Immobilizer communication line | |||
| 15 | LDC converter signal input | |||
| 16 | Main relay control output | Relay OFF | DC | Battery voltage (B+) |
| Relay ON | -0.3 ~ 1.2V | |||
| 17 | - | |||
| 18 | Purge Control Solenoid Valve (PCSV) control output | Inactive Active | Pulse | High: Battery voltage (B+) |
| Low: Max. 1.0V | ||||
| Vpeak: 42.0 ~ 60.0V | ||||
| Frequency: 20Hz | ||||
| 19 | E-CVVT Relay control output | |||
| 20 | - | |||
| 21 | - | |||
| 22 | Injector (Cylinder #2) [High] control output | Engine running | PWM | |
| 23 | Injector (Cylinder #2) [Low] control output | Engine running | Pulse | |
| 24 | - | |||
| 25 | FlexRay communication [Low] signal input | |||
| 26 | - | |||
| 27 | Brake switch [Lamp] signal input | Brake OFF | DC | Max. 0.5V |
| Brake ON | Battery voltage (B+) | |||
| 28 | - | |||
| 29 | - | |||
| 30 | A/C Pressure Transducer (APT) signal input | |||
| 31 | Fuel Tank Pressure Sensor (FTPS) signal input | Idle | Analog | -0.3 ~ 5.2V |
| 32 | LIN communication signal input | |||
| 33 | Fuel pump relay control output | Relay OFF | DC | Battery voltage (B+) |
| Relay ON | -0.3 ~ 1.2V | |||
| 34 | Start control output | Relay OFF | DC | Battery voltage (B+) |
| Relay ON | -0.3 ~ 1.2V | |||
| 35 | Cooling fan relay [High] control output | Relay OFF | DC | Battery voltage (B+) |
| Relay ON | Max. 1.0V | |||
| 36 | - | |||
| 37 | - | |||
| 38 | Canister Close Valve (CCV) control output | Inactive Active | Pulse | High: Battery voltage (B+) |
| Low: Max. 1.0V | ||||
| Vpeak: 42.0 ~ 60.0V | ||||
| 39 | Injector (Cylinder #3) [High] control output | Engine running | PWM | |
| 40 | Injector (Cylinder #3) [Low] control output | Engine running | Pulse | |
| 41 | Battery power (B+) | IG OFF | DC | Max. 1.0V |
| IG ON | Battery voltage (B+) | |||
| 42 | - | |||
| 43 | - | |||
| 44 | Sensor ground | Idle | DC | -0.3 ~ 0.5V |
| 45 | - | |||
| 46 | Sensor ground | Idle | DC | -0.3 ~ 0.5V |
| 47 | Sensor ground | Idle | DC | -0.3 ~ 0.5V |
| 48 | Sensor ground | Idle | DC | -0.3 ~ 0.5V |
| 49 | - | |||
| 50 | Sensor ground | Idle | DC | -0.3 ~ 0.5V |
| 51 | Start relay control output | Relay OFF | DC | Battery voltage (B+) |
| Relay ON | -0.3 ~ 1.2V | |||
| 52 | - | |||
| 53 | - | |||
| 54 | Engine speed signal output | Engine running | Frequency | High: Battery voltage (B+) |
| Low: -0.3 ~ 1.0V | ||||
| Frequency: 21Hz (Idle), 100Hz (3, 000rpm) | ||||
| 55 | - | |||
| 56 | Injector (Cylinder #4) [High] control output | Engine running | PWM | |
| 57 | Injector (Cylinder #4) [Low] control output | Engine running | Pulse | |
| 58 | Heated Oxygen Sensor [Bank 1/Sensor 2] signal input | Idle | DC | Rich: 0.6 ~ 1.0V |
| Lean: Max. 0.4V | ||||
| 59 | CCP-CAN [Low] | Recessive | Pulse | 2.0 ~ 3.0V |
| Dominant | 2.75 ~ 4.5V | |||
| 60 | CAN [Low] | Recessive | Pulse | 2.0 ~ 3.0V |
| Dominant | 2.75 ~ 4.5V | |||
| 61 | starter signal input | S/W OFF | DC | -0.3 ~ 0.5V |
| S/W ON | Battery voltage (B+) | |||
| 62 | - | |||
| 63 | - | |||
| 64 | Accelerator Position Sensor (APS) 2 signal input | C. T | Analog | Max. 1.0V |
| W.O.T | 1.5 ~ 3.0V | |||
| 65 | Accelerator Position Sensor (APS) 1 signal input | C. T | Analog | Max. 1.0V |
| W.O.T | Min. 4.0V | |||
| 66 | - | |||
| 67 | - | |||
| 68 | - | |||
| 69 | - | |||
| 70 | - | |||
| 71 | Cooling fan relay [Low] control output | Relay OFF | DC | Battery voltage (B+) |
| Relay ON | -0.3 ~ 1.2V | |||
| 72 | Variable Intake Solenoid Valve (VIS) control output | Active | DC | Max. 1.0V |
| Inactive | Battery voltage (B+) | |||
| 73 | Injector (Cylinder #1) [High] control output | Engine running | PWM | |
| 74 | Injector (Cylinder #1) [Low] control output | Engine running | Pulse | |
| 75 | Battery power (B+) | IG OFF | DC | Max. 1.0V |
| IG ON | Battery voltage (B+) | |||
| 76 | CCP-CAN [High] | Recessive | Pulse | 2.0 ~ 3.0V |
| Dominant | 2.75 ~ 4.5V | |||
| 77 | CAN [High] | Recessive | Pulse | 2.0 ~ 3.0V |
| Dominant | 2.75 ~ 4.5V | |||
| 78 | Vehicle signal input | |||
| 79 | Sensor power (+5V) | IG OFF | DC | Max. 0.5V |
| IG ON | 4.75 ~ 5.25V | |||
| 80 | - | |||
| 81 | Sensor power (+5V) | IG OFF | DC | Max. 0.5V |
| IG ON | 4.75 ~ 5.25V | |||
| 82 | Sensor power (+5V) | IG OFF | DC | Max. 0.5V |
| IG ON | 4.75 ~ 5.25V | |||
| 83 | - | |||
| 84 | Fuel Level Sender | |||
| 85 | - | |||
| 86 | CVVT Oil Control Valve (OCV) [Bank 1/Intake] control output | Idle | Pulse | High: Battery voltage (B+) |
| Low: -0.3 ~ 1.0V | ||||
| Frequency: 300Hz | ||||
| 87 | - | |||
| 88 | Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 1] Heater control output | Engine running | Pulse | High: Battery voltage (B+) |
| Low: -0.3 ~ 1.0V | ||||
| Frequency: 8 ~ 10Hz | ||||
| 89 | Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 2] Heater control output | Engine running | Pulse | Duty: 0 ~ 100% High: Battery voltage (B+) Low: -0.3 ~ 1.0V Frequency: 8 ~ 10Hz Duty: 0 ~ 100% |
| 90 | Fuel Pressure Regulator Valve [High] control output | Engine running | PWM | |
| 91 | Fuel Pressure Regulator Valve [Low] control output | Engine running | Pulse |