Connector [C100-MK]
| Pin No. | Description | Connected to |
|---|---|---|
| 1 | ECM ground | Chassis ground |
| 2 | ECM ground | Chassis ground |
| 3 | ECM ground | Chassis ground |
| 4 | Battery power (B+) | Main relay |
| 5 | Battery power (B+) | Battery |
| 6 | Battery power (B+) | Battery |
| 7 | Battery power (B+) | Main relay |
| 8 | Sensor ground | Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 2] |
| 9 | Accelerator Position Sensor (APS) 1 signal input | Accelerator Position Sensor (APS) 1 |
| 10 | Sensor ground | Accelerator Position Sensor (APS) 2 |
| 11 | - | |
| 12 | Sensor ground | Fuel Tank Pressure Sensor (FTPS) |
| 13 | - | |
| 14 | Throttle Position Sensor (TPS) 1 signal input | Throttle Position Sensor (TPS) 1 |
| 15 | - | |
| 16 | - | |
| 17 | Fuel Level sender signal input | Fuel Level Sender (FLS) |
| 18 | Sensor power (+5V) | Accelerator Position Sensor (APS) 2 |
| 19 | - | |
| 20 | Sensor power (+5V) | Rail Pressure Sensor (RPS) |
| A/C Pressure Transducer (APT) | ||
| 21 | - | |
| 22 | Electrical load [Wiper] signal input | Multifunction switch |
| 23 | - | |
| 24 | Alternator electric load signal input (FR) | Alternator |
| 25 | - | |
| 26 | - | |
| 27 | - | |
| 28 | - | |
| 29 | Ignition switch signal input | Ignition switch |
| 30 | Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 2] signal input | Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 2] |
| 31 | Accelerator Position Sensor (APS) 2 signal input | Accelerator Position Sensor (APS) 2 |
| 32 | Sensor ground | Accelerator Position Sensor (APS) 1 |
| 33 | - | |
| 34 | - | |
| 35 | Sensor ground | Throttle Position Sensor (TPS) |
| 36 | Throttle Position Sensor (TPS) 2 signal input | Throttle Position Sensor (TPS) 2 |
| 37 | - | |
| 38 | - | |
| 39 | Sensor power (+5V) | Throttle Position Sensor (TPS) 1, 2 |
| 40 | Sensor power (+5V) | Accelerator Position Sensor (APS) 1 |
| 41 | Sensor power (+5V) | Manifold Absolute Pressure Sensor (MAPS) |
| Fuel Tank Pressure Sensor (FTPS) | ||
| 42 | Sensor power (+5V) | Camshaft Position Sensor (CMPS) [Bank 1/Intake] |
| Camshaft Position Sensor (CMPS) [Bank 1/Exhaust] | ||
| 43 | - | |
| 44 | - | |
| 45 | A/C Pressure Transducer (APT) signal input | A/C Pressure Transducer (APT) |
| 46 | Vehicle speed signal input | Vehicle Speed Sensor |
| 47 | - | |
| 48 | - | |
| 49 | - | |
| 50 | - | |
| 51 | - | |
| 52 | VS-/IP- (Common Ground for VS, IP) | Heated Oxygen Sensor [Bank 1/Sensor 1] |
| 53 | Rc/Rp (Pump Cell Voltage) | Heated Oxygen Sensor [Bank 1/Sensor 1] |
| 54 | - | |
| 55 | - | |
| 56 | - | |
| 57 | - | |
| 58 | Rail Pressure Sensor (RPS) signal input | Rail Pressure Sensor (RPS) |
| 59 | - | |
| 60 | Start signal input | PDM module |
| 61 | LIN communication signal input | Battery sensor |
| 62 | - | |
| 63 | CAN [Low] | Other control module, Data Link Connector (DLC), Multi-Purpose Check Connector |
| 64 | Sensor ground | Camshaft Position Sensor (CMPS) [Bank 1/Exhaust] |
| 65 | Camshaft Position Sensor (CMPS) [Bank 1/Exhaust] signal input | Camshaft Position Sensor (CMPS) [Bank 1/Exhaust] |
| 66 | - | |
| 67 | Crankshaft Position Sensor (CKPS) [B] ground | Crankshaft Position Sensor (CKPS) |
| 68 | - | |
| 69 | - | |
| 70 | - | |
| 71 | - | |
| 72 | Purge Control Solenoid Valve (PCSV) control output | Purge Control Solenoid Valve (PCSV) |
| 73 | - | |
| 74 | VS+ (NERNST Cell Voltage) | Heated Oxygen Sensor [Bank 1/Sensor 1] |
| 75 | Rc (Compensated Resistance) | Heated Oxygen Sensor [Bank 1/Sensor 1] |
| 76 | Sensor ground | Rail Pressure Sensor (RPS) |
| 77 | Sensor ground | A/C Pressure Transducer (APT) |
| 78 | Sensor ground | Manifold Absolute Pressure Sensor (MAPS) |
| 79 | Intake Temperature Sensor (IATS) signal input | Intake Temperature Sensor (IATS) |
| 80 | Manifold Absolute Pressure Sensor (MAPS) signal input | Manifold Absolute Pressure Sensor (MAPS) |
| 81 | - | |
| 82 | - | |
| 83 | Immobilizer communication line | Smart Key Control Module [With Button Engine Start System] |
| Immobilizer Control Module [Without Button Engine Start System] | ||
| 84 | - | |
| 85 | CAN [High] | Other control module, Data Link Connector (DLC), Multi-Purpose Check Connector |
| 86 | Sensor ground | Camshaft Position Sensor (CMPS) [Bank 1/Intake] |
| 87 | Camshaft Position Sensor (CMPS) [Bank 1/Intake] signal input | Camshaft Position Sensor (CMPS) [Bank 1/Intake] |
| 88 | Electrical load [Head lamp] signal input | Multifunction switch |
| 89 | Crankshaft Position Sensor (CKPS) [A] signal input | Crankshaft Position Sensor (CKPS) |
| 90 | Canister Close Valve (CCV) control output (Without Immobilizer) | Canister Close Valve (CCV) |
| Fuel pump relay control output (With Immobilizer) | Fuel pump relay | |
| 91 | - | |
| 92 | - | |
| 93 | Main relay control output | Main relay |
| 94 | Start relay (Low) control output | Start relay |
ECM Terminal Input/Output Signal (M/T)
| Pin No. | Description | Condition | Type | Level |
|---|---|---|---|---|
| 1 | ECM ground | Idle | DC voltage | Max. 50mV |
| 2 | ECM ground | Idle | DC voltage | Max. 50mV |
| 3 | ECM ground | Idle | DC voltage | Max. 50mV |
| 4 | Battery power (B+) | IG OFF | DC voltage | Max. 1.0V |
| IG ON | Battery voltage | |||
| 5 | Battery power (B+) | IG OFF | DC voltage | Max. 1.0V |
| IG ON | Battery voltage | |||
| 6 | Battery power (B+) | IG OFF | DC voltage | Max. 1.0V |
| IG ON | Battery voltage | |||
| 7 | Battery power (B+) | IG OFF | DC voltage | Max. 1.0V |
| IG ON | Battery voltage | |||
| 8 | Sensor ground | Idle | DC voltage | Max. 50mV |
| 9 | Accelerator Position Sensor (APS) 1 signal input | Idle | Analog | 0.674 ~ 4.379 V |
| 10 | Sensor ground | Idle | DC voltage | Max. 50mV |
| 11 | - | |||
| 12 | Sensor ground | Idle | DC voltage | Max. 50mV |
| 13 | - | |||
| 14 | Throttle Position Sensor (TPS) 1 signal input | Idle | Analog | 0.33 ~ 4.72 V |
| 15 | - | |||
| 16 | - | |||
| 17 | Fuel Level sender signal input | Idle | Analog | 0.193 ~ 4.0V |
| 18 | Sensor power (+5V) | IG OFF | DC voltage | Max. 0.5V |
| IG ON | 4.9 ~ 5.1V | |||
| 19 | - | |||
| 20 | Sensor power (+5V) | IG OFF | DC voltage | Max. 0.5V |
| IG ON | 4.9 ~ 5.1V | |||
| 21 | - | |||
| 22 | Electrical load [Wiper] signal input | |||
| 23 | - | |||
| 24 | Alternator electric load signal input (FR) | Idle | Pulse | High: Battery voltage |
| Low: Max. 1.5V | ||||
| 25 | - | |||
| 26 | - | |||
| 27 | - | |||
| 28 | - | |||
| 29 | Ignition switch signal input | IG OFF | DC voltage | Max. 1.0V |
| IG ON | Battery voltage | |||
| 30 | Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 2] signal input | Engine | Analog | Rich: 0.6 ~ 1.0V |
| Running | Lean: Max. 0.4V | |||
| 31 | Accelerator Position Sensor (APS) 2 signal input | Idle | Analog | 0.261 ~ 2.204 V |
| 32 | Sensor ground | Idle | DC voltage | Max. 50mV |
| 33 | - | |||
| 34 | - | |||
| 35 | Sensor ground | Idle | DC voltage | Max. 50mV |
| 36 | Throttle Position Sensor (TPS) 2 signal input | Idle | Analog | 0.55 ~ 4.37 V |
| 37 | - | |||
| 38 | ||||
| 39 | Sensor power (+5V) | IG OFF | DC voltage | Max. 0.5V |
| IG ON | 4.9 ~ 5.1V | |||
| 40 | Sensor power (+5V) | IG OFF | DC voltage | Max. 0.5V |
| IG ON | 4.9 ~ 5.1V | |||
| 41 | Sensor power (+5V) | IG OFF | DC voltage | Max. 0.5V |
| IG ON | 4.9 ~ 5.1V | |||
| 42 | Sensor power (+5V) | IG OFF | DC voltage | Max. 0.5V |
| IG ON | 4.9 ~ 5.1V | |||
| 43 | - | |||
| 44 | - | |||
| 45 | A/C Pressure Transducer (APT) signal input | A/C ON | Analog | 0.348 ~ 4.63 V |
| 46 | Vehicle speed signal input | Idle | Pulse | High: Min. 5.4V |
| Low: Max. 2.25V | ||||
| 47 | - | |||
| 48 | - | |||
| 49 | - | |||
| 50 | - | |||
| 51 | - | |||
| 52 | VS-/IP- (Common Ground for VS, IP) | Idle | DC voltage | Max. 50mV |
| 53 | Rc/Rp (Pump Cell Voltage) | Idle | Analog | 0 ~ 5.1V |
| 54 | - | |||
| 55 | - | |||
| 56 | - | |||
| 57 | - | |||
| 58 | Rail Pressure Sensor (RPS) signal input | Idle | Analog | 0.43 ~ 3.46V |
| 59 | Cruise Control Switch signal input | |||
| 60 | Start signal input | ON | DC voltage | Battery voltage |
| OFF | Max. 2V | |||
| 61 | LIN communication signal input | RECESSIVE | Pulse | max 5.6V (at 14V) |
| DOMINANT | min 8.4V (at 14V) | |||
| 62 | - | |||
| 63 | CAN [Low] | RECESSIVE | Pulse | 2.0 ~ 3.0V |
| DOMINANT | 0.5 ~ 2.25V | |||
| 64 | Sensor ground | Idle | DC voltage | Max. 50mV |
| 65 | Camshaft Position Sensor (CMPS) [Bank 1/Exhaust] signal input | Idle | Pulse | High: min. 4.8V |
| Low: Max. 0.6V | ||||
| 66 | - | |||
| 67 | Crankshaft Position Sensor (CKPS) [B] ground | Idle | Pulse | Vp_p: Min. 1.0V |
| 68 | - | |||
| 69 | - | |||
| 70 | - | |||
| 71 | - | |||
| 72 | Purge Control Solenoid Valve (PCSV) control output | Relay OFF | DC voltage | Battery voltage |
| Relay ON | Max. 1.76V | |||
| 73 | - | |||
| 74 | VS+ (NERNST Cell Voltage) | Idle | Analog | 0 ~ 5.1V |
| 75 | Rc (Compensated Resistance) | Idle | Analog | 0 ~ 5.1V |
| 76 | Sensor ground | Idle | DC voltage | - |
| 77 | Sensor ground | Idle | DC voltage | Max. 50mV |
| 78 | Sensor ground | Idle | DC voltage | Max. 50mV |
| 79 | Intake Temperature Sensor (IATS) signal input | Idle | Analog | 0.209 ~ 4.756V |
| 80 | Manifold Absolute Pressure Sensor (MAPS) signal input | Idle | Analog | 0.6683 ~ 4.346V |
| 81 | - | |||
| 82 | - | |||
| 83 | Immobilizer communication line | When transmitting | Pulse | High: Min. 8.4V (at 14V) |
| Low: Max. 6.44V (at 14V) | ||||
| 84 | - | |||
| 85 | CAN [High] | RECESSIVE | Pulse | 2.0 ~ 3.0V |
| DOMINANT | 2.75 ~ 4.5V | |||
| 86 | Sensor ground | Idle | DC voltage | Max. 50mV |
| 87 | Camshaft Position Sensor (CMPS) [Bank 1/Intake] signal input | Idle | Pulse | High: min. 4.8V |
| Low: Max. 0.6V | ||||
| 88 | Electrical load [Head lamp] signal input | |||
| 89 | Crankshaft Position Sensor (CKPS) [A] signal input | Idle | Pulse | Vp_p: Min. 1.0V |
| 90 | Canister Close Valve (CCV) control output (Without Immobilizer) | Active | DC voltage | Battery voltage |
| Inactive | Max. 1.76V | |||
| Fuel pump relay control output (With Immobilizer) | Relay OFF | DC voltage | Battery voltage | |
| Relay ON | Max. 1.44V | |||
| 91 | - | |||
| 92 | - | |||
| 93 | Main relay control output | Relay OFF | DC voltage | Battery voltage |
| Relay ON | Max. 1.7V | |||
| 94 | Start relay control output | Relay OFF | DC voltage | Battery voltage |
| Relay ON | Max. 2.64V |