LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Kia >> 2017 >> Sorento L >> Repair and Diagnosis >> Transmission >> Transmission Control Systems >> Automatic Transaxle Control System - 2.4L >> Torque Converter Control Solenoid Valve (T/CON_VFS) >> Repair Procedures >> Removal
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Repair Procedures: Removal

  1. Remove the under cover.

    (Refer to Engine Mechanical System - "ENGINE ROOM UNDER COVER ").

  2. Drain the coolant.

    (Refer to Engine Mechanical System - "COOLANT ")

  3. Remove the ATF drain plug (A), allow the fluid to drain out and then reinstall the drain plug.

    Tightening torque: 

    33.3 ~ 43.1 N.m (3.4 ~ 4.4 kgf.m, 24.6 ~ 31.8 lb-ft)

    Fig 1: Locating ATF Drain Plug
    G12180449Courtesy of KIA MOTORS AMERICA, INC.
    NOTE: The existing ATF drain plug gasket must be replaced with new one. (Do not reuse it.)
  4. Remove the battery and battery tray.

    (Refer to Engine Electrical System - "BATTERY ")

  5. Remove the wiring bracket mounting bolt (A)

    Tightening torque: 

    9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

    Fig 2: Removing Wiring Bracket Mounting Bolt
    G12180450Courtesy of KIA MOTORS AMERICA, INC.
  6. Disconnect the air breather hose (A) from the valve body cover.
    Fig 3: Disconnecting Air Breather Hose From Valve Body Cover
    G12180451Courtesy of KIA MOTORS AMERICA, INC.
  7. Disconnect the coolant pipe (B) after removing the clamp (A).
    Fig 4: Disconnecting Coolant Pipe Clamp
    G12180452Courtesy of KIA MOTORS AMERICA, INC.
  8. Disconnect the ATF cooler hose (B) after removing the clamp (A).
    Fig 5: Disconnecting ATF Cooler Hose Clamp
    G12180453Courtesy of KIA MOTORS AMERICA, INC.
  9. Remove the valve body cover (A).
    Fig 6: Removing Valve Body Cover
    G12180454Courtesy of KIA MOTORS AMERICA, INC.
  10. Remove the solenoid valve harness (A) and oil temperature sensor (B) after removing the bolts.

    Tightening torque: 

    9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

    Fig 7: Removing Solenoid Valve Harness And Oil Temperature Sensor Bolts
    G12180455Courtesy of KIA MOTORS AMERICA, INC.
  11. Remove solenoid valve support bracket (A).

    Tightening torque: 

    9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

    Fig 8: Removing Solenoid Valve Support Bracket
    G12180456Courtesy of KIA MOTORS AMERICA, INC.
  12. Remove the torque converter control solenoid valve (B) after loosening the bolt (A).

    Tightening torque: 

    9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

    Fig 9: Removing Torque Converter Control Solenoid Valve Bolt
    G12180457Courtesy of KIA MOTORS AMERICA, INC.