Data List/Active Test

DATA LIST

HINT:

Using the hand-held tester's DATA LIST allows switch, sensor, actuator and other item value to be read without removing any parts. Reading the DATA LIST early in troubleshooting is one way to save time.

Connect the hand-held tester (with CAN VIM) to the DLC3.
Turn the engine switch ON.
Read the DATA LIST.

DRIVER DOOR ECU: (SWITCH CONDITION)

SWITCH CONDITION REFERENCE

Item	Measurement Item/Display (Range)	Normal Condition	Diagnostic Note
P/W AUTO SW	D door P/W auto switch ON/OFF	ON: Driver door power window auto switch operates OFF: Driver door power window auto switch does not operate	-
P P/W AUTO SW	P door remote P/W auto switch ON/OFF	ON: Passenger door remote power window auto switch operates OFF: Passenger door remote power window auto switch does not operate	-
RL P/W AUTO SW	RL door remote P/W auto switch ON/OFF	ON: Rear LH door remote power window auto switch operates OFF: Rear LH door remote power window auto switch does not operate	-
RR P/W AUTO SW	RR door remote P/W auto switch ON/OFF	ON: Rear RH door remote power window auto switch operates OFF: Rear RH door remote power window auto switch does not operate	-
LIMIT SW	Jam protection limit switch ON/OFF	ON: Jam protection limit switch operates OFF: Jam protection limit switch do not operates	-

DOOR ECU (PASSENGER, REAR LH, REAR RH): (SWITCH CONDITION)

SWITCH CONDITION REFERENCE

Item	Measurement Item/Display (Range)	Normal Condition	Diagnostic Note
P/W AUTO SW	P/W auto switch ON/OFF	ON: Door power window auto switch operates OFF: Door power window auto switch do not operate	-
LIMIT SW	Jam protection limit switch ON/OFF	ON: Jam protection limit switch operates OFF: Jam protection limit switch do not operates	-

DOOR ECU (ALL DOORS): (GLASS POSITION)

GLASS POSITION REFERENCE

Item	Measurement Item/Display (Range)	Normal Condition	Diagnostic Note
GLASS POS - 1/4	Glass position (Fully close - 1/4 open) OK/CAUTION	OK: Power window is going UP by manual operation CAUTION: CAUTION may be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position	-
GLASS POS - 2/4	Glass position (1/4 open - 2/4 open) OK/CAUTION	OK: Power window is going UP by manual operation CAUTION: CAUTION may be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position	-
GLASS POS - 3/4	Glass position (2/4 open - 3/4 open) OK/CAUTION	OK: Power window is going UP by manual operation CAUTION: CAUTION may be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position	-
GLASS POS - OPEN	Glass position (3/4 open - Fully open) OK/CAUTION	OK: Power window is going UP by manual operation CAUTION: CAUTION may be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position	-

ACTIVE TEST

NOTE: This test causes vehicle parts to move. Please watch your hands.

HINT:

Performing the hand-held tester's ACTIVE TEST allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time. The DATA LIST can be displayed during the ACTIVE TEST.

Connect the hand-held tester to the CAN VIM. Then connect the CAN VIM to the DLC3.
Turn the ignition switch ON.
Performing the ACTIVE TEST by following the directions on the tester screen.

DOOR ECU (ALL DOORS):

ACTIVE TEST REFERENCE

Item	Tester Detail	Diagnostic Note
P/W UP/DOWN	Power Window UP/DOWN	-