LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2007 >> ES 350 >> Repair and Diagnosis >> Restraints >> Restraints Control Systems >> Seat Belt >> Rear Seat Inner Belt Assembly >> Installation
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Rear Seat Inner Belt Assembly: Installation

  1. INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH 
    1. Check the degree of tilt when the ELR begins to lock.
      1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt while gently pulling the belt.
        Fig 1: Checking Degree Of Tilt When ELR Begins To Lock
        G05252018Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        NOTE: Do not disassemble the retractor.
    2. Install the rear seat inner with center belt assembly RH with the bolt.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

      Fig 2: Identifying Rear Seat Inner With Center Belt Assembly RH With Bolt
      G05252017Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade) 
    1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
    2. Engage the 2 clips and 6 claws to install the package tray trim panel assembly.
    Fig 3: Identifying Package Tray Trim Panel Assembly With Clips And Claws
    G05252016Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)  (See INSTALLATION )
  4. INSTALL CENTER STOP LIGHT SET (w/o Rear Sunshade)  (See REMOVAL )
  5. INSTALL REAR SEAT SHOULDER BELT HOLE COVER 
    1. Engage the 4 claws to install the rear seat shoulder belt hole cover.

      HINT:

      Use the same procedure for the other 2 rear seat shoulder belt hole covers.

      Fig 4: Identifying Rear Seat Shoulder Belt Hole Cover With Claws
      G05252015Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH 
    1. Install the floor end of the rear seat inner with center belt assembly RH with the bolt.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

      NOTE: Do not allow the anchor part of the rear seat inner with center belt assembly RH to overlap the protruding parts of the floor panel.
      Fig 5: Identifying Floor End Of Rear Seat Inner With Center Belt Assembly RH With Bolt
      G05252022Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check if the ELR locks.
      NOTE: The check should be performed with the rear seat inner with center belt assembly RH installed.
      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
  7. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH 
    1. Install the floor end of the rear seat 3 point type belt assembly LH with the bolt.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

      NOTE: Do not allow the anchor part of the rear seat 3 point type belt assembly LH to overlap the protruding parts of the floor panel.
      Fig 6: Identifying Rear Seat 3 Point Type Belt Assembly LH With Bolt
      G05252023Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check if the ELR locks.
      NOTE: The check should be performed with the outer belt assembly installed.
      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
  8. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH 

    HINT:

    Use the same procedure for the RH side and the LH side.

  9. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH  (See INSTALLATION )
  10. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH  (See INSTALLATION )
  11. INSTALL REAR SEAT SIDE AIRBAG ASSEMBLY LH (w/ Rear Seat Side Airbag)  (See INSTALLATION )
  12. INSTALL REAR SEAT SIDE AIRBAG ASSEMBLY RH (w/ Rear Seat Side Airbag) 

    HINT:

    Use the same procedure for the RH side and the LH side.

  13. INSTALL REAR SEAT SIDE GARNISH LH (w/o Rear Seat Side Airbag)  (See INSTALLATION )
  14. INSTALL REAR SEAT SIDE GARNISH RH (w/o Rear Seat Side Airbag)  (See INSTALLATION )
  15. INSTALL REAR DOOR SCUFF PLATE LH  (See INSTALLATION )
  16. INSTALL REAR DOOR SCUFF PLATE RH  (See INSTALLATION )
  17. INSTALL REAR SEATBACK ASSEMBLY  (See INSTALLATION )
  18. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY 
  19. INSTALL REAR SEAT HEADREST ASSEMBLY 
  20. INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH 
    1. Install the rear seat inner with center belt assembly LH with the bolt.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

      NOTE: Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.
    Fig 7: Identifying Rear Seat Inner With Center Belt Assembly LH With Bolt
    G05252024Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. INSTALL REAR SEAT CUSHION ASSEMBLY  (See INSTALLATION )
  22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag) 
  23. PERFORM INITIALIZATION (w/ Rear Seat Side Airbag) 
    NOTE: Some systems need initialization after reconnecting the cable to the negative battery terminal (See INITIALIZATION ).
  24. INSPECT SRS WARNING LIGHT (w/ Rear Seat Side Airbag) 

    (See DIAGNOSIS SYSTEM )

scientia non olet · About LEMON Manuals