Rear Seat Inner Belt Assembly: Installation

INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH
1. Check the degree of the tilt when the ELR begins to lock.
  1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt while gently pulling the belt.
    NOTE: Do not disassemble the retractor.
    
    Fig 1: Identifying Degree Of Tilt When ELR Begins To Lock
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Align the claw with the seat belt positioning hole and install the rear seat inner with center belt assembly RH with the bolt.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  Fig 2: Aligning Claw With Seat Belt Positioning Hole
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)
1. Connect the connector to the center stop light assembly.
2. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
3. Engage the 3 clips and 5 claws to install the package tray trim panel assembly and the center stop light assembly as a unit.
  
  Fig 3: Identifying Clips And Claws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Engage the 4 claws to install the rear seat shoulder belt cover center.
  
  Fig 4: Identifying Rear Seat Shoulder Belt Cover Center Claws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Engage the 4 claws to install the rear seat shoulder belt cover LH.
  HINT:
  
  Use the same procedures for the RH side and the LH side.
  
  Fig 5: Identifying Rear Seat Shoulder Belt Cover Claws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Install the floor end of the rear seat inner with center belt assembly RH with the bolt.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  NOTE: Do not allow the anchor part of the rear seat inner with center belt assembly RH to overlap the protruding parts of the floor panel.
  
  Fig 6: Identifying Floor Side Of Rear Seat Inner With Center Belt Assembly RH With Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Check if the ELR locks.
  NOTE: The check should be performed with the outer belt assembly installed.
  1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
8. Install the floor end of the rear seat 3 point type belt assembly LH with the bolt.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  NOTE: Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.
  
  HINT:
  
  Use the same procedures for the RH side and the LH side.
  
  Fig 7: Identifying Floor Side Of Rear Seat 3 Point Type Belt Assembly LH With Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
9. Check if the ELR locks.
  NOTE: The check should be performed with the outer belt assembly installed.
  1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/Rear Sunshade)
1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
2. Engage the 3 clips to install the package tray trim panel assembly.
  
  Fig 8: Identifying Clips On Package Tray Trim Panel Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Engage the 4 claws to install the rear seat shoulder belt cover center.
  
  Fig 9: Identifying Claws On Rear Seat Shoulder Belt Cover Center
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Engage the 4 claws to install the rear seat shoulder belt cover LH.
  HINT:
  
  Use the same procedures for the RH side and the LH side.
  
  Fig 10: Identifying Rear Seat Shoulder Belt Cover Claws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Install the floor end of the rear seat inner with center belt assembly RH with the bolt.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  NOTE: Do not allow the anchor part of the rear seat inner with center belt assembly RH to overlap the protruding parts of the floor panel.
  
  Fig 11: Identifying Floor Side Of Rear Seat Inner With Center Belt Assembly RH With Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Check if the ELR locks.
  NOTE: The check should be performed with the outer belt assembly installed.
  1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
7. Install the floor end of the rear seat 3 point type belt assembly LH with the bolt.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  NOTE: Do not allow the anchor part of the rear seat 3 point type belt assembly LH to overlap the protruding parts of the floor panel.
  
  HINT:
  
  Use the same procedures for the RH side and the LH side.
  
  Fig 12: Identifying Floor Side Of Rear Seat Point Type Belt Assembly LH With Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. Check if the ELR locks.
  NOTE: The check should be performed with the outer belt assembly installed.
  1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
INSTALL ROOF SIDE INNER GARNISH LH (See INSTALLATION )
INSTALL ROOF SIDE INNER GARNISH RH
INSTALL REAR SEAT SIDE GARNISH LH (See INSTALLATION )
INSTALL REAR SEAT SIDE GARNISH RH
INSTALL REAR DOOR SCUFF PLATE LH (See INSTALLATION )
INSTALL REAR DOOR SCUFF PLATE RH
INSTALL BENCH TYPE REAR SEATBACK ASSEMBLY (See INSTALLATION )
INSTALL REAR SEAT CENTER HEADREST ASSEMBLY
INSTALL REAR SEAT HEADREST ASSEMBLY
INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH
1. Install the rear seat inner with center belt assembly LH with the bolt.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  NOTE: Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.
  
  Fig 13: Identifying Rear Seat Inner With Center Belt Assembly LH With Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY (See INSTALLATION )