LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2007 >> LS 460L >> Repair and Diagnosis >> Brakes >> Traction Control >> Brake Control >> Rear Speed Sensor >> Installation
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Rear Speed Sensor: Installation

NOTE: While the battery is connected, even if the engine switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch turns on. Therefore during servicing of the brake system components, do not operate the brake pedal and open/ close the doors while the battery is connected.

HINT:

  1. INSTALL REAR SPEED SENSOR RH 
      Fig 1: Identifying Rear Speed Sensor RH With Bolt
      G04949768Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Install the sensor with the bolt.

      Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf) 

      NOTE:
      • The rear speed sensor is easily damaged. When installing the rear speed sensor to the rear axle hub RH, do not use excessive force to rotate and install it.
      • Prevent foreign matter from attaching to the sensor tip.
      NOTE: Prevent foreign matter from attaching to the sensor tip.
  2. INSTALL SKID CONTROL SENSOR WIRE 
      Fig 2: Identifying Skid Control Sensor Wire
      G04949770Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Connect the connector (labeled A) to the rear speed sensor.
    2. Install the sensor clamp (labeled B) with the bolt (labeled C).

      Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf) 

      NOTE: Do not twist the sensor wire when installing the clamps.
    3. for RH:

      Connect the pad wear indicator connector (labeled D).

    4. Install the sensor clamp (labeled E) with the nut (labeled F).
      Fig 3: Identifying Sensor Clamp With Nut
      G04949771Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) 

      NOTE: Do not twist the sensor wire when installing the clamps.
    5. Except for RH side of models with coil spring type suspension:
      1. Install the sensor clamp (labeled G) with the nut (labeled H).

        Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) 

      2. Connect the rear height control sensor connector (labeled I).
    6. Insert the connector and grommet to the inside of the vehicle through the hole in the wheel house.
      Fig 4: Inserting Connector And Grommet To Inside
      G04949772Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Connect the rear speed sensor wire connector.
      Fig 5: Identifying Rear Speed Sensor Wire Connector
      G04949773Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL REAR WHEEL 

    Torque: 140 N*m (1428 kgf*cm, 103 ft.*lbf) 

  4. INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY RH  (See INSTALLATION )
  5. INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH  (See INSTALLATION )
  6. INSTALL REAR FLOOR FINISH PLATE  (See INSTALLATION )
  7. INSTALL LUGGAGE COMPARTMENT TRIM COVER FRONT  (See INSTALLATION )
  8. INSTALL LUGGAGE COMPARTMENT NO. 2 TRIM HOOK (w/o Rear Cooler)  (See INSTALLATION )
  9. INSTALL LUGGAGE COMPARTMENT NO. 1 LIGHT ASSEMBLY  (See INSTALLATION )
  10. INSTALL DECK TRIM SIDE BOARD LH  (See INSTALLATION )
  11. INSTALL DECK TRIM SIDE BOARD RH  (See INSTALLATION )
  12. INSTALL ROPE HOOK ASSEMBLY  (See INSTALLATION )
  13. INSTALL ROPE HOOK  (See INSTALLATION )
  14. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY  (See INSTALLATION )
  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
  16. INSTALL COWL TOP VENTILATOR LOUVER RH  (See INSTALLATION )
  17. PERFORM INITIALIZATION 
    1. Perform initialization (see INITIALIZATION ).
      NOTE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.
  18. CHECK SPEED SENSOR SIGNAL 
    1. Check the speed sensor signal (see TEST MODE PROCEDURE  ).
scientia non olet · About LEMON Manuals