Freeze Frame Data
- DESCRIPTION
The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
HINT:
If it is impossible to replicate the problem even though a DTC is detected, confirm the freeze frame data.
The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the Intelligent tester or Techstream, five separate sets of freeze frame data, including the data values at the time when the DTC was set, can be checked.
- 3 data sets before the DTC was set.
- 1 data set when the DTC was set.
- 1 data set after the DTC was set.
These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying of the cause of the malfunction, and in judging whether it was temporary or not.
- LIST OF FREEZE FRAME DATA
Intelligent Tester
INTELLIGENT TESTER FREEZE FRAME DATALABEL (Tester Display) Measurement Item/Range Diagnostic Note INJECTOR Injector - IGN ADVANCE Ignition advance - CALC LOAD Calculate load Calculated load by ECM VEHICLE LOAD Vehicle load Load percentage in terms of maximum intake air flow amount MAF Mass air flow volume If value approximately 0.0 g/sec: - Mass air flow meter power source circuit open or short
- VG circuit open or short
If value 160.0 g/sec. or more:- E2G circuit open
ENGINE SPD Engine speed - VEHICLE SPD Vehicle speed Speed indicated on speedometer COOLANT TEMP Engine coolant temperature If value -40°C (-40°F), sensor circuit open
If value 140°C (258°F), sensor circuit shortedINTAKE AIR Intake air temperature If value -40°C (-40°F), sensor circuit open
If value 140°C (258°F), sensor circuit shortedFUEL PRESS Fuel Pressure - AIR-FUEL PATIO Air-fuel ratio - PURGE DENSITY Learning value of purge density - EVAP PURGE FLOW Purge flow - EVAP PURGE VSV EVAP purge VSV duty ratio - KNOCK CRRT VAL Correction learning value of knocking - KNOCK FB VAL Feedback value of knocking - MAFB1 Mass air for volume (bank 1) - MAFB2 Mass air for volume (bank 2) - INTAKE AIR B1 Intake air temperature (bank 1) - INTAKE AIR B2 Intake air temperature (bank 2) - ACCEL POS #1 Accelerator Pedal Position (APP) No. 1 - ACCEL POS #2 APP No. 2 - THROTTLE POS Absolute throttle position Read value with engine switch on (IG) (Do not start engine) THROTTLE POS Throttle sensor positioning Read value with engine switch on (IG) (Do not start engine) THROTTLE POS #2 Absolute throttle sensor positioning #2 - THROTTLE MOT Throttle actuator - O2S B1 S2 Heated oxygen sensor output voltage Performing INJ VOL or A/F CONTROL function of ACTIVE TEST enables technician to check output voltage of sensor O2S B2 S2 Heated oxygen sensor output voltage Performing INJ VOL or A/F CONTROL function of ACTIVE TEST enables technician to check output voltage of sensor AFS B1 S1 A/F sensor output voltage Performing INJ VOL or A/F CONTROL function of ACTIVE TEST enables technician to check output voltage of sensor AFS B2 S1 A/F sensor output voltage Performing INJ VOL or A/F CONTROL function of ACTIVE TEST enables technician to check output voltage of sensor AFS B2 S1 A/F sensor output current Performing INJ VOL or A/F CONTROL function of ACTIVE TEST enables technician to check current output of sensor TOTAL FT #1 Total fuel trim (bank 1) - TOTAL FT #2 Total fuel trim (bank 2) - SHORT FT #1 Short-term fuel trim (bank 1) Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio LONG FT #1 Long-term fuel trim (bank 1) Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central valve SHORT FT #2 Short-term fuel trim (bank 2) Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio LONG FT #2 Long-term fuel trim (bank 2) Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central valve FUEL SYS #1 Fuel system status (bank 1) - OL (Open Loop): Has not yet satisfied conditions to go closed loop
- CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
- OLDRIVE: Open loop due to driving conditions (fuel enrichment)
- OLFAULT: Open loop due to detected system fault
- CLFAULT: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
FUEL SYS #2 Fuel system status (bank 2) - OL (Open Loop): Has not yet satisfied conditions to go closed loop
- CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
- OLDRIVE: Open loop due to driving conditions (fuel enrichment)
- OLFAULT: Open loop due to detected system fault
- CLFAULT: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
O2FT B1 S2 Fuel trim at heated oxygen sensor - O2FT B2 S2 Fuel trim at heated oxygen sensor - AF FT B1 S1 Fuel trim at A/F sensor - AFS B1 S1 A/F sensor output current Performing INJ VOL or A/F CONTROL function of ACTIVE TEST enables technician ' to check current output of sensor AF FT B2 S1 Fuel trim at A/F sensor - O2 LR B1 S1 Lean to Rich response time (bank 1 sensor 1) - O2 LR B2 S1 Lean to Rich response time (bank 2 sensor 1) - O2 RL B1 S1 Rich to Lean response time (bank 1 sensor 1) - O2 RL B2 S1 Rich to Lean response time (bank 2 sensor 1) - CAT TEMP B1S1 Catalyst temperature - CAT TEMP B2S1 Catalyst temperature - CAT TEMP B1S2 Catalyst temperature - CAT TEMP B2S2 Catalyst temperature - S O2S B1 S2 Sub heated oxygen sensor impedance - S O2S B2 S2 Sub heated oxygen sensor impedance - INI COOL TEMP Initial engine coolant temperature - INI INTAKE TEMP Initial intake air temperature - INJ VOL Injection volume - ING TIMMING D4 Injection timing (D4) - FUEL PUMP D4 Fuel pump duty (D4) - COMBUSTION D4 Combustion status (D4) - INJ TIME D4 Injection time (D4) - FP TARGET VAL Target fuel pressure - FP DISCHARGE High pressure fuel pump discharge rate (bank 1) - INJ SWITCHING Prohibition of changing the D-4S injection method - FP DISCHARGE2 High pressure fuel pump discharge rate (bank 2) - ACC RELAY ACC relay status - STARTER RELAY ST relay status - STARTER SIG Starter signal - STARTER CONTROL Starter control - CTPSW Closed throttle position switch - A/C SIGNAL A/C switch status - PNP SW [NSW] Neutral position switch signal - ELECT LOAD SIG Electrical load signal - STOP LIGHT SW Stop light switch status - IMMOBI COMM Immobilizer Communication - FUEL CUT COMN Fuel cut condition - BATTERY VOLTAGE Battery voltage - ATM PRESSURE Atmospheric pressure - BATTERY CURRENT Battery current - BATTERY TEMP Battery temperature - ALT OUTPUT DUTY Generator output duty - ALT V NORMAL Request voltage when regulator not under forced activation - ALT V ACT TST Request voltage when regulator under forced activation - FUEL PMP SP CTL F/PMP relay status - ACIS VSV VSV for ACIS status - EVAP(Purge)VSV Purge VSV VSV for EVAP controlled by ECM (ground side duty control) FUEL PUMP/SPD Fuel pump/speed status - VACUUM PUMP Key-off EVAP system pump status - EVAP VENT VAL Key-off EVAP system vent valve status - FAN MOTOR Fan motor status - TC/TE1 TC and TE1 terminals of DLC3 - ENG SPEED #1 Engine speed for cylinder 1 - ENG SPEED #2 Engine speed for cylinder 2 - ENG SPEED #3 Engine speed for cylinder 3 - ENG SPEED #4 Engine speed for cylinder 4 - ENG SPEED #5 Engine speed for cylinder 5 - ENG SPEED #6 Engine speed for cylinder 6 - ENG SPEED #7 Engine speed for cylinder 7 - ENG SPEED #8 Engine speed for cylinder 8 - ENG SPEED ALL Engine speed for all cylinders - ACIS MOT DUTY ACIS motor duty - VVT CHNG ANGL#1 VVT change angle (bank 1) - VVT EX HOLD B1 VVT exhaust hold duty ratio learning value (bank 1) - VVT EX CHG ANG1 VVT exhaust change angle (bank 1) - VVT EX OCV D B1 VVT exhaust OCV duty (bank 1) - VVT CHNG ANGL#2 VVT change angle (bank 2) - VVT EX HOLD B2 VVT exhaust hold duty ratio learning value (bank 2) - VVT EX CHG ANG2 VVT exhaust change angle (bank 2) - VVT EX OCV D B2 VVT exhaust OCV duty (bank 2) - MD VVT AIM ANG1 MD VVT aim angle (bank 1) - MD VVT AIM ANG2 MD VVT aim angle (bank 2) - MD VVT Mot B1 MD VVT motor detection (bank 1) - MD VVT Mot B2 MD VVT motor detection (bank 2) - FCIDL Idle fuel cut ON: when throttle valve fully closed and engine speed over 1500 rpm FC TAU FC TAU Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete ENG RUN TIME Accumulated engine running time - TIME DTC CLEAR Cumulative time after DTC cleared - DIST DTC CLEAR Accumulated distance after DTC cleared - WU CYC DTC CLEAR Warm-up cycle after DTC cleared - Techstream
TECHSTREAM FREEZE FRAME DATALABEL (Tester Display) Measure Item/Range Diagnostic Note Injector Injector - IGN Advance Ignition advance - Calculate Load Calculate load Calculated load by ECM Vehicle Load Vehicle load Load percentage in terms of maximum intake air flow amount MAF Mass air flow volume If value approximately 0.0 g/sec: - Mass air flow meter power source circuit open or short
- VG circuit open or short
If value 160.0 g/sec. or more:- E2G circuit open
Engine Speed Engine speed - Vehicle Speed Vehicle speed Speed indicated on speedometer Coolant Temp Engine coolant temperature If value -40°C (-40°F), sensor circuit open
If value 140°C (258°F), sensor circuit shortedIntake Air Intake air temperature If value -40°C (-40°F), sensor circuit open
If value 140°C (258°F), sensor circuit shortedFuel Press Fuel Pressure - Air-Fuel Ratio Air-fuel ratio - Purge Destiny Learn Value Learning value of purge density - Evap Purge Flow Purge flow - EVAP (Purge) VSV EVAP purge VSV duty ratio - Knock correct Learn Value Correction learning value of knocking - Knock Feedback Value Feedback value of knocking - MAF Bank1 Mass air for volume (bank 1) - MAF Bank2 Mass air for volume (bank 2) - Intake Air Bank1 Intake air temperature (bank 1) - Intake Air Bank2 Intake air temperature (bank 2) - Accelerator Pedal Position No.1 Accelerator Pedal Position (APP) No. 1 - Accelerator Pedal Position No.2 APP No. 2 - Throttle Position Absolute throttle position Read value with engine switch on (IG) (Do not start engine) Throttle Sensor Position Throttle sensor positioning Read value with engine switch on (IG) (Do not start engine) Throttle Sensor Position #2 Absolute throttle sensor positioning #2 - Throttle Motor Throttle actuator - O2S B1 S2 Heated oxygen sensor output voltage Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor O2S B2 S2 Heated oxygen sensor output voltage Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor AFS B1 S1 A/F sensor output voltage Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor AFS B2 S1 A/F sensor output voltage Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor AFS B2 S1 A/F sensor output current Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check current output of sensor Total FT #1 Total fuel trim (bank 1) - Total FT #2 Total fuel trim (bank 2) - Short FT #1 Short-term fuel trim (bank 1) Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio Long FT #1 Long-term fuel trim (bank 1) Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central valve Short FT #2 Short-term fuel trim (bank 2) Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio Long FT #2 Long-term fuel trim (bank 2) Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central valve Fuel System Status (bank 1) Fuel system status (bank 1) - OL (Open Loop): Has not yet satisfied conditions to go closed loop
- CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
- OLDrive: Open loop due to driving conditions (fuel enrichment)
- OLFault: Open loop due to detected system fault
- CLFault: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
Fuel System Status (bank2) Fuel system status (bank 2) - OL (Open Loop): Has not yet satisfied conditions to go closed loop
- CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
- OLDrive: Open loop due to driving conditions (fuel enrichment)
- OLFault: Open loop due to detected system fault
- CLFault: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
O2FT B1 S2 Fuel trim at heated oxygen sensor - O2FT B2 S2 Fuel trim at heated oxygen sensor - AF FT B1 S1 Fuel trim at A/F sensor - AFS B1 S1 A/F sensor output current Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check current output of sensor AF FT B2 S1 Fuel trim at A/F sensor - O2 LR B1 S1 Lean to Rich response time (bank 1 sensor 1) - O2 LR B2 S1 Lean to Rich response time (bank 2 sensor 1) - O2 RL B1 S1 Rich to Lean response time (bank 1 sensor 1) - O2 RL B2 S1 Rich to Lean response time (bank 2 sensor 1) - Catalyst Temp (B1 S1) Catalyst temperature - Catalyst Temp (B2S1) Catalyst temperature - Catalyst Temp (B1 S2) Catalyst temperature - Catalyst Temp (B2 S2) Catalyst temperature - Sub O2S Impedance B1S2 Sub heated oxygen sensor impedance - Sub O2S Impedance B2S2 Sub heated oxygen sensor impedance - Initial Engine Coolant Temp Initial engine coolant temperature - Initial Intake Air Temp Initial intake air temperature - Injection Volum (Cylinder 1) Injection volume - Injection Timing (D4) Injection timing (D4) - Fuel Pump Duty (D4) Fuel pump duty (D4) - Injection Time (D4) Injection time (D4) - Fuel Pressure Target Value Target fuel pressure - HP FP Discharge Rate High pressure fuel pump discharge rate (bank D - Injection Switching Status Prohibition of changing the D-4S injection method - HP FP Discharge Rate 2 High pressure fuel pump discharge rate (bank 2) - ACC Relay ACC relay status - Starter Relay ST relay status - Starter Signal Starter signal - Starter Control Starter control - Closed Throttle Position SW Closed throttle position switch - A/C Signal A/C switch status - Neutral Position SW Signal Neutral position switch signal - Electrical Load Signal Electrical load signal - Stop Light Switch Stop light switch status - Immobilizer Communication Immobilizer Communication - Fuel Cut Condition Fuel cut condition - Battery Voltage Battery voltage - Atmosphere Pressure Atmospheric pressure - Battery Current Battery current - Battery Temperature Battery temperature - Alternator Output Duty Generator output duty - Alt Vol - Non Active Test Request voltage when regulator not under forced activation - Alt Vol - Active Test Request voltage when regulator under forced activation - Fuel Pump Speed Control F/PMP relay status - ACIS VSV VSV for ACIS status - EVAP Purge VSV Purge VSV VSV for EVAP controlled by ECM (ground side duty control) Fuel Pump Speed Status Fuel pump/speed status - Vacuum Pump Key-off EVAP system pump status - EVAP System Vent Value Key-off EVAP system vent valve status - Electric Fan Motor Fan motor status - TC and TE1 TC and TE1 terminals of DLC3 - Engine Speed of Cyl #1 Engine speed for cylinder 1 - Engine Speed of Cyl #2 Engine speed for cylinder 2 - Engine Speed of Cyl #3 Engine speed for cylinder 3 - Engine Speed of Cyl #4 Engine speed for cylinder 4 - Engine Speed of Cyl #5 Engine speed for cylinder 5 - Engine Speed of Cyl #6 Engine speed for cylinder 6 - Engine Speed of Cyl #7 Engine speed for cylinder 7 - Engine Speed of Cyl #8 Engine speed for cylinder 8 - An Engine Speed of All Cyl Engine speed for all cylinders - ACIS Motor Duty ACIS motor duty - VVT Change Angle (Bank 1) VVT change angle (bank 1) - VVT Ex Hold Lrn Val (Bank 1) VVT exhaust hold duty ratio learning value (bank 1) - VVT Ex Chg Angle (Bank 1) VVT exhaust change angle (bank 1) - VVT Ex OCV Duty (Bank 1) VVT exhaust OCV duty (bank 1) - VVT Change Angle (Bank2) VVT change angle (bank 2) - VVT Ex Hold Lrn Val (Bank2) VVT exhaust hold duty ratio learning value (bank 2) - VVT Ex Chg Angle (Bank2) VVT exhaust change angle (bank 2) - VVT Ex OCV Duty (Bank2) VVT exhaust OCV duty (bank 2) - MD VVT Aim Angle (Bank 1) MD VVT aim angle (bank 1) - MD VVT Aim Angle (Bank2) MD VVT aim angle (bank 2) - MD VVT MOT Direction B1 MD VVT motor detection (bank 1) - MD VVT MOT Direction B2 MD VVT motor detection (bank 2) - Idle Fuel Cut Idle fuel cut ON: when throttle valve fully closed and engine speed over 1500 rpm FC TAU FC TAU Fuel cut being performed under very light toad to prevent engine combustion from becoming incomplete Engine Run Time Accumulated engine running time - Time after DTC Cleared Cumulative time after DTC cleared - Distance from DTC Cleared Accumulated distance after DTC cleared - Warmup Cycle Cleared DTC Warm-up cycle after DTC cleared -