Speed Sensor: Installation

INSTALL SPEED SENSOR SP2

Fig 1: Locating Speed Sensor NC2 And Bolt
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Install the speed sensor to the transmission case with the bolt.
  Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
2. Connect the sensor connector.
INSTALL SPEED SENSOR NC3

Fig 2: Locating Speed Sensor NC3 And Bolt
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Install the speed sensor to the transmission case with the bolt.
  Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
2. Connect the sensor connector.
INSTALL SPEED SENSOR NT

Fig 3: Locating Speed Sensor Connector
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Coat a new O-ring with ATF and install it to the speed sensor.
2. Using a T30 "TORX" wench, install the speed sensor with the bolt.
  Torque: 6.8 N*m (69 kgf*cm, 60 in.*lbf)
3. Connect the sensor connector.
INSTALL TRANSMISSION VALVE BODY ASSEMBLY
1. Install the spring and check ball body.
  
  Fig 4: Identifying Check Ball Body And Spring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Align the groove of the manual valve with the lever pin.
  
  Fig 5: Aligning Groove Of Manual Valve With Lever Pin
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the 17 bolts.
  
  Fig 6: Locating Valve Body Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 11 N*m (112 kgf*cm, 8 ft.*lbf)
  
  HINT:
  
  Each bolt length is indicated below.
  
  Bolt length:
  
  21 mm (0.83 in.) for bolt A
  
  31 mm (1.22 in.) for bolt B
  
  64 mm (2.52 in.) for bolt C
4. Install the detent spring and detent spring cover with the bolt.
  
  Fig 7: Locating Bolt, Detent Spring Cover And Detent Spring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  NOTE: Make sure to install the detent spring so that its roller is perpendicularly at the center of the manual valve lever.
  
  Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
5. Connect the 8 connectors to the solenoid valves.
  
  Fig 8: Locating Solenoid Valves Connectors
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Connect the oil pressure switch connector.
7. Coat a new O-ring with ATF and install it to the ATF temperature sensor.
8. Install the ATF temperature sensor and lock plate with the bolt.
  Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
INSTALL VALVE BODY OIL STRAINER ASSEMBLY
1. Coat a new O-ring with ATF and install it to the oil strainer.
  
  Fig 9: Identifying O-Ring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  NOTE: Ensure that the O-ring is not twisted or pinched.
2. Install the oil strainer to the valve body with the 4 bolts.
  
  Fig 10: Locating Valve Body Oil Strainer Assembly Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 11 N*m (112 kgf*cm, 8 ft.*lbf)
INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
1. Install the 3 magnets to the oil pan.
  
  Fig 11: Identifying Magnets To Oil Pan
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install a new gasket and the oil pan to the transmission case with the 9 bolts.
  
  Fig 12: Locating Oil Pan Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 7.4 N*m (75 kgf*cm, 65 in.*lbf)
  NOTE:
  - Make sure that there is no oil or foreign matter on the gasket seal surface and oil pan contact surface.
  - Install the gasket so that there is no slack in the gasket, and that the seal surface's entire circumference is level.
  - Make sure that the 9 gasket drop prevention protrusions are set on the oil pan.
  - When tightening the oil pan, make sure that the gasket is not pinched between the gasket tightening area's sleeve and the transmission's seal surface.
    
    Fig 13: Identifying Correct Installation Of Sleeve
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
INSTALL COWL TOP VENTILATOR LOUVER (See INSTALLATION )
ADD AUTOMATIC TRANSMISSION FLUID
1. Add automatic transmission fluid (see AUTOMATIC TRANSMISSION FLUID ).
PERFORM INITIALIZATION
1. Perform initialization (see INITIALIZATION ).
  NOTE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.