Inspection Procedure

1. Disconnect the transmission control switch connector (See REMOVAL  ).
2. Turn the engine switch off.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance 

   STANDARD RESISTANCE SPECIFICATION
   
   

   Tester Connection	Condition	Specified Condition
   J43-5 (E) - Body ground	Always	Below 1 Ω

Fig 1: Identifying J43 Transmission Control Switch Connector Terminal
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to Next Step 

1. Disconnect the transmission control switch connector.
2. Turn the engine switch on (IG).
3. Measure the voltage according to the value(s) in the table below.

   Standard Voltage 

   STANDARD VOLTAGE SPECIFICATION
   
   

   Tester Connection	Switch Condition	Specified Condition
   J43-3 (IG) - Body ground	Engine switch on (IG)	11 to 14 V
   	Engine switch off	Below 1 V

Fig 2: Identifying J43 Transmission Control Switch Connector Terminal
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to Next Step 

1. Disconnect the transmission control switch connector.
2. Measure the resistance between each terminal of the transmission control switch when the shift lever is moved to each position.

   Standard Resistance 

   STANDARD RESISTANCE SPECIFICATION
   
   

   Tester Connection	Condition	Specified Condition
   3 (IG) - 7 (S)	Shift lever in M, "+" or "-"	Below 1 Ω
   	Shift lever not in M, "+" or "-"	10 kΩ or higher
   2 (SFTU) - 5 (E)	Shift lever held in "+" (Up-shift)	Below 1 Ω
   	Shift lever not held in "+"	10 kΩ or higher
   1 (SFTD) - 5 (E)	Shift lever held in "-" (Down-shift)	Below 1 Ω
   	Shift lever not held in "-"	10 kΩ or higher

   Fig 3: Identifying Transmission Control Switch Connector Terminal

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPLACE TRANSMISSION CONTROL SWITCH  (See REMOVAL  )

OK: Go to Next Step 

1. Connect the transmission control switch connector.
2. Disconnect the ECM connector.
3. Turn the engine switch on (IG).
4. Measure the voltage according to the value(s) in the table below.

   Standard Voltage 

   STANDARD VOLTAGE SPECIFICATION
   
   

   Tester Connection	Condition	Specified Condition
   A6-16 (S) - Body ground	Engine switch on (IG) Shift lever in M, "+" or "-"	11 to 14 V
   A6-16 (S) - Body ground	Engine switch on (IG) Shift lever not in M, "+" or "-"	Below 1 V

   Fig 4: Identifying ECM Connector Terminal

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Turn the engine switch off.
6. Disconnect the spiral cable connector
7. Measure the resistance according to the value(s) in the table below

   Standard Resistance 

   STANDARD RESISTANCE SPECIFICATION
   
   

   Tester Connection	Condition	Specified Condition
   A6-8 (SFTU) - Body ground	Shift lever held in "+" (Up-shift)	Below 1 Ω
   	Shift lever not held in "+"	10 kΩ or higher
   A6-7 (SFTD) - Body ground	Shift lever held in "-" (Down-shift)	Below 1 Ω
   	Shift lever not held in "-"	10 kΩ or higher

Fig 5: Identifying A6 ECM Connector Terminal
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE  (See PROBLEM SYMPTOMS TABLE  )